563551
4
Zoom out
Zoom in
Previous page
1/83
Next page
6 © HAMILTON 14/01/2013 INSTRUCTION MANUAL 7
3. Operating instructions 3. Operating instructions
Using the chronograph
Start-Stop function
Timing a single event:
 Press button A: the chronograph starts.
. Press button A: the chronograph stops.
 Press button B to reset to zero.
Note: Before you start timing, the hands should be reset
to zero. If necessary, press button B.
Cumulative time function
This measures successive times. Each result is added
to the previous one.
 Press button A: the chronograph starts.
. Press button
A again: the chronograph stops.
Repeat these two steps as many times as desired. At the
end of the last measurement, the chronograph displays
the total of all the times measured. Press button B to
reset to zero.
Split-time function (intermediate times)
This function allows the display and reading of mul-
tiple successive times measured from the same start-
ing point. The time taken to read the amounts can be
caught up on without disturbing the measurement of
total elapsed time.
 Press button A: the chronograph starts.
. Press button B to read the rst intermediate time.
 Press button
B
again. The chronograph hands catch
up with the time elapsed since the beginning of the
measurement.
 Similarly, press button B again to read a further inter-
mediate time, and once again to cause the hands to
catch up.
 At the end of the whole measurement, press button
A to read the total time.
 Press button B to reset to zero.
NB: The maximum catch-up time is  minutes.
. Mechanical watch
Mechanical movement. The most traditional of move-
ments in watchmaking is the mechanical one. To en-
sure that the watch does not stop, it must be wound
regularly – once a day.

Setting the time
 Pull out the crown
C completely to position (p).
. Set the time by turning the crown in the desired
direction.
 Push the crown back in completely to position (p):
the seconds hand starts again, allowing perfect syn-
chronization with a time signal.
Caliber -
Setting the time
 Pull out the crown
C
completely to position (p): the
seconds hand stops.
. Set the time by turning the crown in the desired
direction.
 Push the crown back in completely to position (p):
the seconds hand starts again, allowing perfect syn-
chronization with a time signal.
Setting the date
 Pull out the crown
C to position (p).
. Turn the crown clockwise to set the date.
 Push the crown back in completely to position (p).
. Automatic watch
Automatic movement. The mechanism of the watch
includes an oscillating rotor that winds the mainspring
via the motion of your wrist. The running reserve is ap-
proximately  hours ( hours for the caliber H- and
H-). If necessary, the watch may be rewound manually.
With most of our models, the beauty of the inner work-
ing of the watch movement can be admired through
the transparent case back.


Setting the time
 Pull out the crown
C
completely to position (p): the
seconds hand stops*.
. Set the time by turning the crown in the desired
direction.
 Push the crown back in completely to position (p):
the seconds hand starts again, allowing perfect syn-
chronization with a time signal.
* stop seconds according to model
Setting the date and the day
 Pull out the crown
C to position (p).
. Turn the crown clockwise to set the date and coun-
terclockwise to display the desired day.
 Push the crown back in completely to position (p).
. Automatic chronograph watch

Setting the time
 Pull out the crown
C
completely to position (p): the
seconds hand stops.
. Set the time by turning the crown in the desired
direction.
 Push the crown back in completely to position (p):
the seconds hand starts again, allowing perfect syn-
chronization with a time signal.
Setting the date and the day
 Pull out the crown C to position (p).
. Turn the crown clockwise to set the date and coun-
terclockwise to display the desired day.
 Push the crown back in completely to position (p).
Note: Rapid date and day correction is not possible be-
tween  p.m. and  a.m.

Setting the time
 Pull out the crown
C
completely to position (p): the
seconds hand stops.
. Set the time by turning the crown in the desired
direction.
 Push the crown back in completely to position (p):
the seconds hand starts again, allowing perfect syn-
chronization with a time signal.
Setting the date
Set the date* by pressing button D. The date changes
at each press.
* date correction is not possible between . p.m.
and  p.m.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hamilton 2826 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hamilton 2826 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 10,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info