Manual Hama EWS390 - 104935 (page 6 of 27) (English, German, Dutch, French, Polish)

607516

Zoom out

Zoom in

1/27

DISCONNECTED SIGNALS

If without obvious reasons the display of the outdoor temperature goes

blnk, hold for 2 seconds to enforce an immediate search.

If that fails, check:

1. The remote unit is still in place.

2. The batteries of both the remote unit and main unit. Replace as

necessary

NOTE: When the temperature falls below freezing point, the batteries

of outdoor units will freeze, lowering their voltage supply and the

effective range.

3. The transmission is within range and path is clear of obstacles and

interference. Shorten the distance when necessary.

TRANSMISSION COLLISION

Signals from other household devices, such as door bells, home security

systems and entry controls, may interfere with those of this product and

cause temporarily reception failure. This is normal and does not affect the

general performance of the product. The transmission and reception of

temperature readings will resume once the interference recedes.

How to change the temperature Alarm Setting

1. Press once TEMP ALARM button.

2. Then Press and hold TEMP ALARM button for 2 seconds

3. Enter the Hi or Lo temperature alert setting value by using

or button

4. Press TEMP ALARM once to exit.

HOW TO SET THE RADIO CONTROLLED CLOCK

1. After the batteries are installed. The clock will automatically search the

radio signal. It takes about 3-8 minutes to ﬁ nish this process.

2. If user wish’s to disable the auto-reception feature, holds the front

panel for 2 seconds to disable it.

3. To enable the auto-reception feature again, holds the for 2 seconds

again to force it receive and allow it receive at desired time.

4. If the radio signal is received, the date & time will be set automatically

with radio control signal icon turns on.

5. If the clock fails to receive the time signal, it will be show as icon.

then user can set the time manually.

CALENDAR CLOCK DISPLAY MODE

The clock and the calendar share the same section of the display. The

calendar is displayed in a day-month format. Each press on the MODE

button will change the display between clock with second, clock with day

of week, zone time with day of week. Zone time with second and ay-month.

HOW TO SET THE CLOCK MANUALLY

To set the clock manually, hold MODE for 3 seconds, the day of the week

will be ﬂ ashing. Press or keys to select between English, German,

French, Italian, Spanish, Dutch and Swedish. Press MODE to conﬁrm.

Repeat the same procedure to set, °C/°F , year, month, date, date-month

format, 12/24, hour and minute. During the setting, press and hold or

will increase or decrease the value rapidly. If there is an item you do not

wish to change , simply press MODE to bypass the item.

When you ﬁ nished the change, press MODE to exit. The display will return

to the clock mode.

HOW TO SET AND ARM THE ALARM

To set an alarm,

1. Press ALARM once to display alarm time. If the alarm is disarmed, the

time will be displayed as OFF

2. Hold ALARM for two seconds. The hour digits will blink.

3. Enter the hour using or .

4. Press ALARM . The minute digits will blink.

5. Enter the minutes using or .

6. Press ALARM to exit.

7. Repeat the same procedure to set single alarm

ALARM FEATURE

- Weekday Alarm

This function allows you to restrict the alarm to weekday (Monday to

Friday). The alarm is activated and the weekday symbol lights up if the

weekday alarm function was set and the alarm time is reached. There is

no alarm on Saturdays and Sundays for this alarm function.

- Single alarm

The alarm sound will be activated and the icon will be ﬂ ashed once

when it is armed and the alarm time is reach. Once it ﬁ nished, it will be

disabled automatically.

- Pre-Alarm

The pre-alarm sound will be activated and the icon will be ﬂ ashed if

outdoor temperature under or equal two degree C. Which is

programmable 15, 30, 45, 60 or 90 minutes earlier than the weekday

alarm or single alarm time.

HOW TO SET THE ZONE TIME

To set the zone time,

1. Press MODE until at zone time display mode,

2. Hold MODE for 3 seconds, the zone time offset will be displayed.

3. Enter the offset using or .

4. Press MODE to exit.

The alarm , and Pre-AL icons will be displayed indicating which

alarm is armed. You can also arm or disarm an alarm by pressing the or

button at alarm display mode. Press MODE to return to clock display

mode.

Snooze Feature

When the alarm sound is on, press the snooze key enter snooze mode.

After 8 minuts, alarm sound will be wake up automatically. The snooze

cycle will be restarted if you press the snooze key again. If you leave the

alarm sound on for 2 minutes, it will enter snooze mode automatically with

maximum 3 times.

How to stop an alarm

Press ALARM on the unit to stop an alarm.

PRECAUTIONS

This product is engineered to give you years of satisfactory service if you

handle it carefully. Here are a few precautions:

1. Do not immerse the unit in water

2. Do not clean the unit with abrasive or corrosive materials. They may

scratch the plastic parts and corrode the electronic circuit.

3. Do not subject the unit to excessive force, shock, dust, temperature

or humidity which may result in malfunction, shorter electronic life span,

damaged battery and distorted parts.

4. Do not taper with the unit´s internal components. Doing so will invalidate

the warranty on the unit and may cause unnecessary damage. The unit

contains no user-serviceable parts.

5. Only use fresh batteries as speciﬁed in the user´s manual. Do not mix

new and old batteries as the old ones may leak.

6. Always read the user´s manual thoroughly before operating the unit.

SPECIFICATIONS

Temperature Measurement

Main Unit

Indoor Temperature measurement

Proposed operating range:

-5.0°C to + 50°C

Humidity measuring range:

R.H. 25% to 90%

Temperature resolution:

0,1°C / 0,2°F

Humidity resolution:

1 % R.H.

Remote unit

Proposed operating range:

-10°C to + 60°C

Temperature resolution:

0,1°C / 0,2°F

RF Transmission Frequency:

433 MHz

Maximum No. of Remote unit: 3

RF Transmission Range:

Maximum 30 meters (open area)

Temperature sensing cycle:

around 43 – 47 seconds

Relative Humidity Measurement

Remote relative humidity measurement range

25 % RH to 95% RH

Resolution:

1 % RH

Barometric Pressure Measurement

Pressure measuring range:

750 to 1100 mb/hPa at 25°C ( 22.15to 32.49 inHg)

Pressure sampling cycle:

20 minutes

Moon Phase functions

Moon Phase scanner Range:

forward / backward 39 days

Calendar Clock

12/24 h display with hh: mm

Date Format: Day- Month or Month-day.

Day of week selectable in 7 language (English, German, French, Italian,

Spanish, Dutch and Swedish),

Dual 2-minute crescendo alarm

Pre-alarm for ice alert

Power

Main unit

use 2 pcs UM-3 or AA 1,5V battery

Remote sensing unit

use 2pcs UM-3 or AA 1,5V battery

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hama EWS390 - 104935 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hama EWS390 - 104935 Manual

Product: