607816

Hama 40098 - 8in1 Manual

7
Zoom out
Zoom in
Previous page
1/30
Next page
12
13
You put the initial remote control and yours
40098 so there, that the send/receiver diodes
of the two Remote controls lie against each
other. Pay attention also to the regular height
direction of the two diodes. Guarantee that
the distance is about 2,5 cm (Thumb width)
between the 2 remote controls.
Copying of the keys
• Hold the key setup (16) pressed for approx.
3 seconds until the red LED lights up
permanently.
• Making key SETUP (16) go.
• Once the source key (3) (TV, STB, CBL,
AUDIO, AUX, VCR, CD, DVD) the key goes
out and shines again on.
• Pressing the key LEARN (18) once.
• To press the key of yours 40098 once,
under which one you copy the keys of the
original-remote.
• To hold the key of the original remote
control to be copied pressed, the red
LED goes out and again lights up (2 to 3
seconds). With an error fl ashes the red
LED 3 seconds long, stays, however, in the
learning-mode. You attempt it once again
or change to another key.
• Repeat the procedure for the other keys
from step 5.
• Press the key SETUP (16) if all wanted keys
are copied.
• The red LED goes out.
Recommendations
• Do not move the remote controls during
the process
• You guarantee, that it during the room light
not around fl uorescent tubes or energy
saving-lamps act since these sources of
light can cause troubles and infl uence the
copy.
• The 2 remote controls must be away over a
meter of every source of light.
• Avoid the copying of the codes of the keys
V+; Of- and as well as the playing keys‘ (5),
because according to
The codes of these keys do absolutely not
control remote control the same devices.
• If the memory of yours 40098 is full, the
red LED fl ashes for 3 seconds. Then it is
not more possible, to copy other codes
without carrying out some accrued
liabilities.
• If you copy a key, it is possible that the red
LED fl ashes weakly. Let in this case
the key not rid and you wait, to which
fl ashing stops.
Tips:
• The batteries of the 2 remote controls must
be in good repair; exchange it possibly.
• They can not copy any keys among
following keys: LEARN, SETUP,
• All keys under a mode are put out, when
a four-digit code under this mode is input
(also for the direct input of a code, the
search of a code or a brand).
Delete of all copied keys
• Hold the key setup (16) pressed for approx.
3 seconds until which red LED lights up
permanently.
• Making key SETUP (16) go.
• Pressing the key LEARN (18) twice. The red
LED goes out and lights up again.
• Pressing the key SETUP (16) that red LED
goes from once.
• All copied keys are will be deleting.
Normal use
After you have carried out the programming
of your remote control for yours audio/video
device, the remote control works in the most
common primary functions as the original
remote control of the respective device.
Focus your remote control on the wanted
device and press the corresponding source
key. The red LED will light up shortly.
They activate the functions now through
pressing of the corresponding function key of
your universal remote control.
At every keystroke the red LED lights up
shortly.
Possibly every function of your original
remote control is not directly available on the
universal remote control.
In particular near newer devices it is possible
that the functions are fi rst of all put aside or
not at all available among other keys than
expected.
With the AV Taste you choose usually the
AV input of the TV set for e.g. the STB
receiver or the video recorder.
Special functions
„electronic program“
The key EPG (13) corresponds to the function
„Electronic Program Guide“ and has different
functions, depending on which device this
is used.
At STB - or VCR - codes keep you up the key
a programming carry out, provided that
your video recorder about a SHOWVIEW
- function.
“Punch through”
The punch through function lets you execute
specifi c functions on a device type other
than the one that is selected. These are the
volume, mute, and playback functions.
When the remote control is set to AUDIO,
AUX, VCR, DVD, or CD mode, the Volume (7)
and Mute (17) buttons control the TV device
(provided the other devices do not have their
own volume control).
In TV mode or another mode without
playback functions, the Play, Pause, Stop and
(where applicable) Record buttons control
a connected video recorder, DVD player,
or DVD recorder. The controlled device is
always the last selected device.
By default, the universal remote control is
set so that the volume and mute functions
automatically control the TV set when a
source button for a video device (DVD, video
recorder, etc.) is being pressed.
Programming volume/mute to a different
device type
• Press and hold the Setup (16) button
for approx. 3 seconds until the red LED
remains lit.
00040098bda.indd Abs1:12-Abs1:1300040098bda.indd Abs1:12-Abs1:13 08.10.2009 10:24:55 Uhr08.10.2009 10:24:55 Uhr
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hama 40098 - 8in1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hama 40098 - 8in1 in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info