Manual Hama 00020307 - 5in1 (page 2 of 13) (English, German, Dutch, French, Italian)

607804

Zoom out

Zoom in

1/13

Easy programming for the control of your CD PLAYER (not for 5 in

1 model)

To programme the remote control to operate your CD PLAYER, proceed as described for the

television set. Complete steps 1 to 10 except you must first press and release the key

followed by holding down the key. Please ensure that you refer to the codes listed under

the CD section and not the TV section.

Easy programming for the control of your TUNER (RADIO) (not for

5 in 1 model)

To programme the remote control to operate your TUNER, proceed as described for the CD

PLAYER but using the key instead of the CD key. Please ensure that you refer to the

codes listed under the TUNER section and not the CD PLAYER section.

Easy programming for the control of your TAPE RECORDER (TAPE

DESK) (not for 5 in 1 model)

To programme the remote control to operate your TAPE RECORDER, proceed as described for

the CD PLAYER but using the key instead of the CD key. Please ensure that you refer to

the codes listed under the TAPE section and not the CD PLAYER section.

Easy programming for the control of your AMPLIFIER (not for 5 in

1 model)

To programme the remote control to operate your AMPLIFIER, proceed as described for the

CD PLAYER. Complete steps 1 to 10, using the key on your remote control. Please ensure

that you refer to the codes listed under the AMPLIFIER section and not CD PLAYER section.

Code scan

If programming using the codes in the enclosed list failed to work then you must next try the

automatic code scan.

A. Ensure that the remote control is equipped with 2 new batteries (see step one of easy

programming procedure).

B. Switch on your TV SET. When using the automatic scan function for the VCR, DVD, CD or

TAPE, switch on your device, insert a video tape, DVD, CD or tape cassette and put the unit

into ‘Play mode’ i.e, the VCR tape etc is running.

C. Press the key of your remote control for approx. 4 seconds until the LED flashes twice.

D. After seeing the 2 flashes and within 5 seconds, enter the code . After entering the

code the LED will flash twice indicating that the code has been accepted

E. Press and hold the key until your TV switches off. Please note that this process might

take up to 15 minutes. During the automatic scanning you can remove your finger or

change hands provided it is replaced within 8 seconds. If left off of the key for more than 8

seconds then the remote will revert back to its normal mode. If your TV switches into

Stand-By mode during the automatic process then immediately remove your finger from

the key and then press the key until the LED flashes twice, this will then store the

code that the remote control has found.

F. In some cases during the automatic scanning search the remote control might find several

codes that appear to operate your TV etc, however, if some of the buttons fail to work

properly then it’s possible the remote has found a partially compatible code. In such cases

you will need to restart the automatic scanning process (steps B. to F.) until a better code is

found. Please note that once the automatic process is restarted, the remote continues from

the last stored code and not at the beginning of code database.

• To complete a code scan for the VCR, DVD, CD or TAPE, follow the procedure above but

use the key and not the key

• To complete a code scan for the TUNER, follow the procedure above but use the key

AMP

TAPE

TUNER

SHIFT

UNIVERSAL REMOTE CONTROL

Thank you for purchasing this universal remote control. Before using the remote you will need

to insert two type "CR2025" batteries (for all Linum models) or two AAA "LR03" batteries (for

AlveusLux 10 and 5 in 1 models) in the battery compartment ensuring that you follow the

polarity shown on the inside. You can now use your remote control to operate up to 10 different

devices including a TV, video recorder, DVD player, satellite or cable receiver, CD player, tuner

(radio), tape recorder and amplifier. If your remote control is equipped with an AUX key then

you can also use it to control a second TV set, video recorded, satellite receiver and/or cable

box, CD player, tuner, tape recorder or amplifier!

Easy programming for the control of your TV SET

1. Insert 2 new batteries of type "CR2025" or "AAA/LR03" (depending on your model).

Observe battery polarity as indicated in the battery compartment.

2. Switch on your TV SET.

3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).

4. Beside the manufacturer's name, you will find one or more 3-digit codes. These codes

must be entered into the remote to enable it to work with your particular TV set.

5. Press the key on the remote control for approximately 4 seconds until the LED flashes

twice.

6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical code from the

list.

7. After entering the code the LED will flash twice indicating that the code has been accepted.

8. Point the remote control towards your TV and press the key. If your TV does not

respond by going into Stand-By mode then repeat steps 3 to 8 and enter the next code in

the list.

9. If your TV goes into Stand-By mode when the key pressed then your remote control

has found a compatible code. Next test all of the other function buttons. If certain functions

are not working correctly then restart the process moving onto the next code number as

this may well improve the situation.

10. If the codes in the list fail to operate your TV then next move onto the automatic code scan

function (see below).

Easy programming for the control of your VIDEO RECORDER

To programme the remote control to operate your VIDEO RECORDER, proceed as described

above for the television set. Complete steps 1 to 10 using the key on your remote control.

Please ensure that you refer to the codes listed under the VIDEO RECORDER section and not

the TV section.

Easy programming for the control of your SATELLITE RECEIVER

To programme the remote control to operate your SATELLITE RECEIVER or CABLE BOX,

proceed as described for the television set. Complete steps 1 to 10 using the key on your

remote control. Please ensure that you refer to the codes listed under the SATELLITE section

and not the TV section.

Easy programming for the control of your DVD PLAYER

To programme the remote control to operate your DVD PLAYER, proceed as described for the

television set. Complete steps 1 to 10 using the key on your remote control. Please ensure

that you refer to the codes listed under the DVD section and not the TV section.

DVD

SAT

VCR

USER MANUAL

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hama 00020307 - 5in1 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hama 00020307 - 5in1 Manual

Product: