Manual Hako Scrubmaster B140R (page 31 of 38) (English)

683782

Zoom out

Zoom in

1/38

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Maintenance work

Compliance with our recommenda-

tions concerning maintenance work

will give you the certitude of always

having a machine at your disposal,

which is ready to work and in good

operating condition.

It is better to take precautions than to

repair damages – and less expensive!

Please contact your local Hako ser-

vice center; the people there will be

glad to perform that work for you.

There, well-trained personal and

genuine Hako spare parts are at your

disposal. In case of any inquiries or

orders for spare parts, please always

quote the machine’s serial number

mentioned on the nameplate.

The nameplate is fixed to the right

front part in the battery compartment.

When cleaning or servicing the ma-

chine, and when replacing any parts,

shut off the motors and on principle

disconnect the battery plug; moreover

take precautions so as to protect the

unit against unintentional movements

or against being inadvertently started.

For reasons of safety during cleaning

and/or maintenance work in or on

the tank, the tank lid – when lifted –

must be secured so as to prevent

accidental closing or tilting down.

The machine may be taken into opera-

tion only if all guarding devices are

fitted and in protective position.

As far as possible, cleaning should

not be done by hand, but using

appropriate tools or equipment.

Maintenance, repair and adjustment

work may be carried out only by

means of suitable tools and by people

trained in the factory.

When using or replacing batteries,

battery connection cables, battery

charger units comply with the manu-

facturer’s instructions.

For reasons of safety, only genuine

Hako spare parts must be used.

Note: Do not clean the machine by

means of vapor jet or high pressure

cleaning equipment but by means of a

water hose (pressure: approx. 5 to 6

bar) and from the top to the bottom.

Do not allow water to get into any

opening, slits, on electronic modules,

control panels or seals.

Do not allow water to get on the seat

console as it may be collected on the

battery stored below the seat.

Let the machine dry after cleaning

e.g. for the week-end. The use of

aggressive and caustic detergents is

not allowed.

The legal regulations and the local

provisions have to be complied with

when discharging detergents.

The Hakomatic B 910 is equipped

with a service display. If a malfunction

occurs during operation, e.g. a de-

fective fuse, a 4-digit number will

appear in the display (hourmeter), the

4 dots will start flashing simultaneous-

ly and the buzzer sounds. This 4-digit

number advises the service technician

in detail on the last error found.

This facilitates fast repair action. The

following table lists some of the

possible errors displayed. You may

eventually remedy yourself.

Scrubmaster B140 R is equipped

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hako Scrubmaster B140R in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hako Scrubmaster B140R Manual

Product: