683780
20
Zoom out
Zoom in
Previous page
1/30
Next page
4.6 Electrical equipment
E Fuse for vacuum motor
F Over load protector
brush motor
The electrical equipment of the Hako-
matic E 430 uses a mains voltage of
230V/50 Hz AC.
Easy access to brush motor and
suction turbine is possible after the up-
per part of the unit has been titled to
upside.
The suction turbine has been provided
with a fuse (E ) having a rating of T6A.
It must be replaced by a fuse of same
rating (T stands for Time -lag).
Suction turbine require little mainte-
nance only; just the carbon brushes
must be checked- renewed, if requi-
red- after every
200 service hours.
The brush motor is protected by a cur-
rent sensitive overload protector ( F )
which requires to be manually reset in-
case of tripping. When brush motor
trips identify the cause and correct it
before trying to run the machine.
The protector can be reset by pressing
the transparent dome on the electrical
box cover. Please allow approximately
30 seconds time before resetting.
Note: If there should be repeated
cases of failure, look for the reason.
Any work at the electrical system has
to be carried out by specialized electri-
cians only.
Whenever performing work at the
electrical system, disconnect the
mains supply plug on principle. When
work at the electrical system is finis-
hed, a safety test,( as per VDE 0701,
sections 1and 3, has to be performed).
18
4. Inbetriebnahme
E
F
Fig.15
4.6 Electrical equipment
E Fuse for vacuum motor
F Over load protector
brush motor
The electrical equipment of the Hako-
matic E 430 uses a mains voltage of
230V/50 Hz AC.
Easy access to brush motor and
suction turbine is possible after the up-
per part of the unit has been titled to
upside.
The suction turbine has been provided
with a fuse (E ) having a rating of T6A.
It must be replaced by a fuse of same
rating (T stands for Time -lag).
Suction turbine require little mainte-
nance only; just the carbon brushes
must be checked- renewed, if requi-
red- after every
200 service hours.
The brush motor is protected by a cur-
rent sensitive overload protector ( F )
which requires to be manually reset in-
case of tripping. When brush motor
trips identify the cause and correct it
before trying to run the machine.
The protector can be reset by pressing
the transparent dome on the electrical
box cover. Please allow approximately
30 seconds time before resetting.
Note: If there should be repeated
cases of failure, look for the reason.
Any work at the electrical system has
to be carried out by specialized electri-
cians only.
Whenever performing work at the
electrical system, disconnect the
mains supply plug on principle. When
work at the electrical system is finis-
hed, a safety test,( as per VDE 0701,
sections 1and 3, has to be performed).
18
4. Inbetriebnahme
E
F
Fig.15
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hako Hakomatic E 430 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hako Hakomatic E 430 in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info