465460
38
Zoom out
Zoom in
Previous page
1/40
Next page
18
M
AINTENAN
C
E
DISPLAY CODES
DISPLAY CODES AND SPECIAL FUNCTIONS
¬ Control panel lock function: Press the "Delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program.
It can no longer be changed by operating buttons or knobs. To unlock press the "Delay" and "Start/Pause" buttons again for 3
seconds.
¬ Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycle, the present
settings will be saved and the preset operation will resume when the power is on again.
¬ To cancel a program
Press the "Start/Pause" button, then switch off the power and the program is automatically cancelled. Turn the program selector
again to choose another program.
Note: During the spin process, if too much foam is inspected, in order to protect the motor, the washing machine will eliminate the
foam automatically; the motor will stop and the drain pump will drain the water continuously for 90 seconds. If it happens more than
3 times, the motor will stop until the end of cycle without spinning.
CODES
CAUSES SOLUTIONS
Err1 ¬ Door is not properly shut. _ Shut the door properlyˈand then press the Start/Pause button.
Err2 ¬ Drainage error, water not emptied within 6
minutes.
_ Clean the filter and check the drain hose for blockage. If error
still exists, please contact the maintenance personnel.
Err3 ¬ Temperature sensor not properly connected or
damaged.
_ Contact the maintenance personnel.
Err4
¬ Heater error (Appears at the end of a cycle).
_ Contact the maintenance personnel.
Err5 ¬Water level not met in 8 minutes.
¬The height of the drain hose is below 80 cm.
¬ The drain hose is in water.
.lamronsierusserpretawdna,nodenrutsipattahterusekaM_
If problem still exists, please contact the maintenance personnel.
_ Install drain hose within 80-100 cm of height.
_ Make sure the drain hose is not in water.
Err7 ¬ Motor error. _ Contact the maintenance personnel.
Err8 ¬ Water exceeds protective level. _ Contact the maintenance personnel.
End ¬ End of wash cycle.
1:25 ¬The remaining time is 1 hour 25 minutes.
19:30 ¬Status information:Preset time for delayed operation.
UNb After the last rinsing cycle finishes,spinning fails completely due to unbalance of the laundry.
EuAr ¬ The PBC and the motor cant’t communicate. _ Contact the maintenance personnel.
Er10 _ Contact the maintenance personnel.
¬ The signal of Water level sensor is wrong.
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haier HW70-B1286-F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haier HW70-B1286-F in the language / languages: English, French as an attachment in your email.

The manual is 10,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info