817810
10
Zoom out
Zoom in
Previous page
1/132
Next page
8
Setting The Temperature Controls
When pressing “ or button, the system will be entering the set up mode in the upper or lower
compartment automatically. The LED will start flashing and display the actual temperature.
Press once the button, the temperature will decrease or increase 1 ℃. When exceeding the minimum value that
can be established, it will jump to the highest adjustable temperature value automatically. After stopping pressing
the button for 5 seconds, LED figure will stop flash, then revert back to display the temperature of the upper or
lower compartment.
After the unit is unplugged, the system will return to the acquiescence temperature, which is set by the
factory. The acquiescence temperature is as below:
Upper compartment: 6 ℃
Lower compartment: 12 ℃
Upper compartment: The temperature setting can be adjusted from 5to 10℃.
Lower compartment: The temperature setting can be adjusted from 10℃ to 18℃.
Temperature Alarm
If the temperature inside is higher than 23 , it will display "HI" on the display panel, and after one hour after the alarm / buzzer
will sound. This indicates that the temperature inside is too high. If the temperature inside is lower than 0 , it will display "LO"
on the display panel and at the same time the alarm also malfunction indicator is active.
Temperature Recollection Function
In the event of a power interruption, wine chiller can remember the previous temperature settings, and when the power
is recovery, the cooler temperature will go back the same setting temperature as power off.
Overtime Open the Door Alarm
When you forget close the door or the door is not closed completely, the buzzer alarm after 5 minutes. Please close the
door completely and avoid the cold energy was lost.
Internal light
In order to reduce energy consumption, the LED light within this wine cabinet will automatically switch off when
closed the door. If you would prefer the LED light to remain on continuously, this is possible. Please press and hold
the “LIGHT” bottom for 5 seconds, the display will show “LP”. After 4 seconds the display will revert back to normal
and the light will remain on until manually switched off.
If you would like to revert back and conserve energy (recommended), press and hold the “LIGHT” button for 5
seconds, the display will show “LF”. After 4 seconds the display will revert back to normal
the light will be on when door open and the light turn off when door closed.
Replaceable (LED only) light source by a professional
This product contains a light source of energy efficiency class G.
EN
If you want to display each actual indoor temperature, press the corresponding button " Set Upper " or " Set
Lower ", and the LED will flash and display the current temperature. After you stop pressing the button for 5
seconds, the LED figure will stop flashing, then revert back to show the set temperature.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haier HAKWBD 60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haier HAKWBD 60 in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 12.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info