710928
7
Zoom out
Zoom in
Previous page
1/56
Next page
7
Remaining battery capacity indication
Battery indicator status
Remaining battery
capacity
: On : Off : Blinking
50% – 100%
20% – 50%
0% – 20%
Charge the battery
015527
Switch action (Fig. 3 & 4)
CAUTION:
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the “OFF” position when
released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger, push
in the lock button and then release the switch trigger.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Speed change (Fig. 5)
The maximum air volume can be adjusted just by turning
the adjusting dial. This can be done even while the tool
is running. The dial is marked 1 (lowest) to 6 (highest).
NOTICE:
The speed adjusting dial can be turned only as far as 6
and back to 1. Do not force it past 6 or 1, or the speed
adjusting function may no longer work.
When working in a high temperature circumstance, the
tool may be stopped because of the overheat protection
system. In that case let the tool cool down. Avoid setting
to speed 6 (highest) in high temperature circumstances.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Installing the long nozzle (Fig. 6 & 7)
To install the long nozzle:
1. Align the small projection of the housing with the
groove of the long nozzle.
2. Slide in the long nozzle, and turn it clockwise until the
triangle markings on the long nozzle and the housing
meet each other.
The length of the nozzle can be adjusted by changing the
locking position.
Installing the shoulder strap (optional accessory)
(Fig. 8)
Hook the shoulder strap onto the hanger of the tool.
Before use, adjust the length of strap so that it is easy
to work with it.
OPERATION
Blowing (Fig. 9)
CAUTION:
Do not place the blower on the ground while it is
switched on. Sand or dust may enter from suction inlet,
and they may result in personal injury.
Hold the blower rmly with a hand and perform the
blowing operation by moving it around slowly.
When blowing around a building, a big stone or a
vehicle, direct the nozzle away from them.
When performing an operation in corner, start from the
corner and then move to wide area.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Cleaning (Fig. 10)
From time to time, wipe off the outside of the tool using a
cloth dampened in soapy water.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
These accessories or attachments are recommended
for use with your Makita tool specied in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Makita genuine battery and charger
Shoulder belt
NOTE:
Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
ENG108-1
Noise
The typical A-weighted noise level determined according
to EN50636:
Sound pressure level (L
pA
): 79.1 dB (A)
Uncertainty (K): 1.8 dB (A)
Sound power level (L
WA
): 93.5 dB (A)
Uncertainty (K): 2.3 dB (A)
Wear ear protection
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haier AFE735C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haier AFE735C in the language / languages: Dutch as an attachment in your email.

The manual is 3,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haier AFE735C

Haier AFE735C User Manual - Dutch, French - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info