657539
224
Zoom out
Zoom in
Previous page
1/252
Next page
Winora Group
Original operating manual
Cycle
(all categories including city/trekking/MTB/racing/fitness bikes)
User manual
Pedelec/S-pedelec
Supplementary user manual
Children’s bike
Supplementary user manual
Balance bike
User manual
EN
Europe
USA
Guide
to the original operating manual
Guide
Contents
1 Information online � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
2 Warnings � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
3 Explanation of symbols� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
4 Illustrations � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
5 Explanation of terminology � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
5�1 Pedelec/EPAC � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
5�2 S-pedelec/S-EPAC � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
5�3 Children’s bikes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
5�4 Balance bikes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
5�5 Lockout� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
5�6 Sag � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
5�7 Crankset � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
5�8 Glossary � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
6 Units and abbreviations � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
7 User manual structure� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
8 Further information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
9 A note on maintenance and repair work � � � � � � � � � � � � � � � � � � 9
10 A note on technical specifications � � � � � � � � � � � � � � � � � � � � � � 9
Guide Information online
1
This guide will provide you with an overview of all the signs and symbols used in this
original operating manual. For the sake of clarity, the original operating manual will be
referred to below as the user manual.
1 Information online
The following paragraph is only applicable for Europe:
Additional information about adjustments, care and maintenance can be found in the
download area at www.winora-group.de/manuals. Here you can download a more
comprehensive user manual for your cycle.
More information about the respective brands can be found at:
Website Brand(s)
www.winora.de Winora
www.haibike.com Haibike
www.staiger-fahrrad.de Staiger, Sinus
The following paragraph is only applicable for the USA:
Additional information about adjustments, care and maintenance can be found in the
download area at www.winora-group.de/manuals. Here you can download a more
comprehensive user manual for your cycle.
More information about the respective brands can be found at:
Website Brand(s)
www.haibike.com Haibike
2 Warnings
The following signal symbols and signal words are used in this user manual to warn
against personal injury or damage to property.
Warnings are intended to draw attention to possible dangers. Failure to follow a warning
may result in injury to yourself or other people, as well as causing property damage.
Read and follow all warnings.
DANGER
This warning identifies a hazard with a high degree of risk, resulting in serious
injury or death if not avoided.
GuideExplanation of symbols
2
WARNING
This warning identifies a hazard with a moderate degree of risk, resulting in
serious injury if not avoided.
CAUTION
This warning identifies a hazard with a low degree of risk, resulting in minor or
moderate injury if not avoided.
NOTE
This warning calls attention to potential property damage.
3 Explanation of symbols
The following symbols may be used in this original operating manual, on cycle
components or on packaging.
Symbol Explanation
This symbol provides you with useful additional information about adjustment or use.
This symbol indicates that more information is available online.
This symbol indicates that you must read the user manual.
This symbol identifies the age rating for young children.
This symbol is an example indicating the cycle category. Refer to the sticker on
your cycle to find out its cycle category. You can find a comprehensive description
of the cycle categories in the “Cycle categories” chapter of the cycle user manual.
Guide Explanation of symbols
3
The following symbols are only applicable for Europe:
Symbol Explanation
Products marked with this symbol meet all applicable European Economic
Community regulations.
This symbol is an example indicating the maximum gross weight limit for the cycle.
Refer to the sticker on your cycle to find out its maximum gross weight limit.
The following symbols are only applicable for the USA:
Symbol Explanation
This example symbol identifies a class 1 pedelec, which has a power rating of
500Watts and travels no faster than 20 mph.
This example symbol identifies a class 3 S-pedelec, which has a power rating of
350 Watts and travels no faster than 28 mph.
285 lbs
This symbol is an example indicating the maximum gross weight limit for the cycle.
Refer to the sticker on your cycle to find out its maximum gross weight limit.
GuideIllustrations
4
4 Illustrations
The illustrations in this user manual are examples and may differ from the actual design
of your cycle. If you lack the necessary expertise regarding your cycle model, contact
your dealer.
Example of an illustration:
Illustr.: Illustration structure
1 Example illustration
2 Caption
Illustr.: Correct handlebar
alignment
1
2
5 Explanation of terminology
The following terms are used in this user manual:
5.1 Pedelec/EPAC
Contrary to the official standard, EPACs (electric power-assisted cycles) are referred to in
this user manual as pedelecs (from “pedal electric cycle”).
The following paragraph is only applicable for Europe:
Pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 25 km/h when you pedal.
Depending on the cycle model, there may be a pushing aid which can accelerate the
cycle up to 6 km/h depending on what gear the shifting system is in.
The following paragraph is only applicable for the USA:
Pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 20 mph when you pedal. By law, pedelecs are class 1 (see the “Explanation
of symbols” chapter). There may be a pushing aid depending on the cycle model.
How this functions is described in more detail in the drive system user manual enclosed
with the cycle.
Pedelecs are cycles that are legally classed as bikes in most countries. Acquaint yourself
with the national and regional regulations and classification in your country.
Guide Explanation of terminology
5
5.2 S-pedelec/S-EPAC
Contrary to the official standard, S-EPACs (speed electric power-assisted cycles) are
referred to in this user manual as S-pedelecs (from “speed pedal electric cycle”).
The following paragraph is only applicable for Europe:
S-pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 45 km/h when you pedal. Depending on the model, all-electric operation
up to a maximum of 18 km/h may also be possible.
The following paragraph is only applicable for the USA:
S-pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 28 mph when you pedal. There may be a pushing aid depending on the
cycle model. How this functions is described in more detail in the drive system user
manual enclosed with the cycle. By law, S-pedelecs are class 3 (see the “Explanation of
symbols” chapter).
In some countries, S-pedelecs are classed as motor vehicles. Acquaint yourself with the
national and regional regulations and classification in your country.
5.3 Children’s bikes
Children’s bikes are pedal-powered category 0 cycles for children, with 12" and 16" wheels.
5.4 Balance bikes
Balance bikes are category 0 cycles without pedals for children aged 3 years and up.
Balance bikes are pushed along as the child moves.
5.5 Lockout
The lockout feature locks the suspension fork. This can reduce bob or squat in the front
fork, e.g. where the suspension sinks when pedalling hard.
Depending on the cycle model, the rear suspension may also be equipped with a
lockout feature (see the “Suspension” chapter in the cycle user manual).
5.6 Sag
Sag is the amount of compression in suspension elements which is caused by the rider’s
body weight. Depending on the model of the suspension fork or suspension, and depending
on the intended use, the sag is adjusted to a value between 15 % and 40 % of the total
suspension travel.
GuideExplanation of terminology
6
5.7 Crankset
A crankset (sometimes known as a chainset) is an assembly consisting of chainrings,
pedals and cranks.
1 Chainring
2 Pedal
3 Crank
Illustr.: Crankset using the example of a derailleur shifting system with 3 chainrings
5.8 Glossary
A glossary of terms used in this user manual is included after the balance bike manual.
3
2
1
Guide Units and abbreviations
7
6 Units and abbreviations
The following units and abbreviations can be found in this user manual or on
components of your cycle:
Unit Meaning Unit for
° Degree Angular measurement
°C Degrees Celsius Temperature
°F Degrees Fahrenheit Temperature (USA)
1/s per second Revolutions
" Inches Unit of measurement (USA), 1 inch = 2.54 cm
A Amperes Electrical current
Ah Ampere hours Electrical charge
bar Bars Pressure
g Grams Mass (weight)
h Hours Time
Hz Hertz Frequency
kg Kilograms Mass (weight)
km/h Kilometres per hour Speed
kPa Kilopascals Pressure
lbs Pounds Mass (weight USA)
mph Miles per hour Speed (USA)
Nm Newton metres Torque
psi Pounds per square inch Pressure (USA)
V Volts Electrical voltage
W Watts Electrical power
Wh Watt hours Electrical capacity
GuideUser manual structure
8
7 User manual structure
This original operating manual contains four user manuals:
1. Cycle user manual
Provides the basis for all cycle categories, except in the case of the balance bike
user manual.
Contains information for the following cycle categories:
x Read the entire user manual carefully, paying particular attention to the safety
notes.
2. Pedelec and S-pedelec supplementary user manual
Contains specific information about pedelecs and S-pedelecs in addition to the
cycle user manual.
Contains information for the following cycle categories:
x Read the entire pedelec and S-pedelec supplementary user manual carefully
as well.
3. Children’s bike supplementary user manual
Contains specific information about children’s bikes in addition to the cycle user
manual.
Contains information for the following cycle category:
x Read the entire children’s bike supplementary user manual carefully as well.
4. Balance bike user manual
Contains all information about balance bikes.
Contains information for the following cycle category:
x Read the entire balance bike user manual carefully.
Guide Further information
9
8 Further information
You should receive all important documents and necessary information from your dealer
along with your cycle:
The completed cycle passport document and handover certificate, which
can be found at the end of the standard print version of the original operating
manual.
A standard print version of the original operating manual for your cycle.
The original operating manual with more information can be found online at:
www.winora-group.de/manuals.
If purchasing a pedelec, you will also receive a quick-start guide for the pedelec
drive system. A complete original operating manual for your drive system can
be found online at: www.winora-group.de/manuals.
If purchasing an S-pedelec, you will also receive a complete original operating
manual for your S-pedelec drive system.
On your cycle you will find:
The cycle category number for your cycle
The maximum gross weight limit
x Compare the details specified on your cycle passport and the cycle category
number on your cycle against the “User manual structure” chapter to find all the
information about your cycle model.
9 A note on maintenance and repair work
Only carry out steps described in the user manual if you have the necessary expertise
and the tools required. Otherwise have the work carried out by a dealer.
10 A note on technical specifications
Written information on the technical specifications and equipment for your cycle model is
available from your dealer.
Winora Group
User manual
Cycle
Cycle
1 Seat tube 16 Crank
2 Top tube 17 Chainrings
3 Down tube 18 Chain
4 Handlebar stem 19 Kickstand
5 Handlebars 20 Chain stays
6 Brake lever 21 Rear derailleur
7 Front fork/suspension fork 22 Cassette of sprockets
8 Headlamp 23 Reflector
9 Front brake 24 Rear lamp
10 Spoke 25 Luggage carrier
11 Tyre 26 Seat stays
12 Valve 27 Rear brake
13 Wheel hub 28 Saddle clamp
14 Rim 29 Seat post clamp
15 Pedal 30 Saddle
Example illustration
1
2
3
4
5
6
7
8
12
13
14
15
16
17
23
24
25
27
28
30
29
26
11
9
18
19
20
22
21
10
Cycle
Contents
1 Basics .......................................... . . 1
1.1 Reading and storing the user manual . . . . . . . . . . . . . . . . . . 1
1.2 Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Cycle categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.4 Maximum gross weight limit. . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Seating position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.6 Frame height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.7 Helmet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.8 Luggage carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.8.1 Luggage carrier with clamp . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.8.2 Luggage carrier with bungee cord and no clamp . . . . . . . . . . . . . 8
1.8.3 Low-rider luggage carrier for panniers . . . . . . . . . . . . . . . . . . . 9
1.8.4 Luggage system carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.9 Kickstand variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.9.1 Side kickstand and rear kickstand . . . . . . . . . . . . . . . . . . . . .10
1.9.2 Bipod kickstand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
1.10 Aero handlebars on racing bikes. . . . . . . . . . . . . . . . . . . . 11
2 Before setting off.................................. . 12
2.1 Before every ride . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.2 Before the first ride. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3 Safety ........................................... . 15
3.1 General safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2 Notes on road use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.3 Notes on carrying children. . . . . . . . . . . . . . . . . . . . . . . . 20
3.3.1 Child seat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.3.2 Child trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.4 Notes on transportation . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.4.1 Notes on luggage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.4.2 Notes on fitting trailers . . . . . . . . . . . . . . . . . . . . . . . . . . .25
3.4.3 Notes on cargo and dog trailers. . . . . . . . . . . . . . . . . . . . . . .25
3.4.4 Notes on transporting the cycle by car . . . . . . . . . . . . . . . . . . .26
3.5 Notes on torques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.6 Notes on screw turning directions . . . . . . . . . . . . . . . . . . . 28
3.7 Notes on wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cycle
3.8 Notes on carbon components . . . . . . . . . . . . . . . . . . . . . . 30
3.8.1 Falls and accidents . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
3.8.2 Bike carriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
3.8.3 Torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
3.9 Residual risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4 Basic adjustments................................. . 33
4.1 Quick releases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.2 Saddle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.2.1 Adjusting the saddle height . . . . . . . . . . . . . . . . . . . . . . . . .35
4.2.2 Minimum insertion depth . . . . . . . . . . . . . . . . . . . . . . . . . .36
4.2.3 Adjusting the minimum pull-out height . . . . . . . . . . . . . . . . . . .36
4.2.4 Adjusting the saddle tilt . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.2.5 Adjusting the reach . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.3 Handlebars and handlebar stems . . . . . . . . . . . . . . . . . . . . 38
4.3.1 Minimum insertion depth . . . . . . . . . . . . . . . . . . . . . . . . . .38
4.3.2 Adjusting the handlebar stem tilt . . . . . . . . . . . . . . . . . . . . . .39
4.3.3 Aligning the handlebars . . . . . . . . . . . . . . . . . . . . . . . . . . .39
4.4 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.5 Brake lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.5.1 Adjusting the position . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
4.5.2 Adjusting the grip width . . . . . . . . . . . . . . . . . . . . . . . . . . .41
4.6 Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.6.1 Folding pedal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
4.6.2 Block pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
4.6.3 Clipless pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
4.6.4 Foot clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
4.7 Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.7.1 Hub dynamo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
4.7.2 Battery-powered and rechargeable lighting . . . . . . . . . . . . . . . .46
4.7.3 Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
4.7.4 Rear lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
4.7.5 Reflectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
4.8 Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5 Brake ........................................... . 48
5.1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
5.1.1 Coaster brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Cycle
5.1.2 Brake lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
5.1.2.1 Disc brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
5.1.2.2 Rim brake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
5.2 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
5.2.1 Adjusting the brake cable tension in mechanical brakes . . . . . . . . .51
5.2.2 Adjusting the pressure point . . . . . . . . . . . . . . . . . . . . . . . .52
5.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
5.3.1 Operating the brake lever . . . . . . . . . . . . . . . . . . . . . . . . . .53
5.3.2 Operating the coaster brake. . . . . . . . . . . . . . . . . . . . . . . . .54
5.4 Bedding in disc brakes . . . . . . . . . . . . . . . . . . . . . . . . . 54
5.5 Maintaining braking force . . . . . . . . . . . . . . . . . . . . . . . . 55
6 Derailleur shifting system ........................... . 55
6.1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1.1 Mechanical derailleur shifting system. . . . . . . . . . . . . . . . . . . .56
6.1.2 Electronic derailleur shifting system . . . . . . . . . . . . . . . . . . . .56
6.1.3 Gear combinations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
6.2 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.2.1 Adjusting the rear derailleur . . . . . . . . . . . . . . . . . . . . . . . . .59
6.2.2 Adjusting the front derailleur . . . . . . . . . . . . . . . . . . . . . . . .60
6.2.3 Readjusting the shift cable tension . . . . . . . . . . . . . . . . . . . . .60
6.2.4 Adjusting the derailleur shifting system on a racing bike . . . . . . . . .61
6.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.3.1 Shifting sprockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
6.3.2 Shifting chainrings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
6.3.3 Electronic derailleur shifting system . . . . . . . . . . . . . . . . . . . .64
6.3.4 Derailleur/hub shifting system (Dual Drive) . . . . . . . . . . . . . . . . .64
6.3.5 Operating the shift levers on a racing bike . . . . . . . . . . . . . . . . .64
7 Hub shifting systems............................... . 65
7.1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
7.1.1 Automatic shifting system (Automatix) . . . . . . . . . . . . . . . . . . .65
7.1.2 Stepless gear shifting system (NuVinci). . . . . . . . . . . . . . . . . . .66
7.1.3 Stepless automatic gear shifting system (NuVinci Harmony) . . . . . . . . . 66
7.1.4 Electronic hub shifting system . . . . . . . . . . . . . . . . . . . . . . .66
7.2 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
7.2.1 Adjusting the shift cable tension . . . . . . . . . . . . . . . . . . . . . .67
7.2.2 Adjusting the shift cable tension in a NuVinci shifting system . . . . . . .68
Cycle
7.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7.3.1 Hub shifting systems with gear levels. . . . . . . . . . . . . . . . . . . .70
7.3.2 Stepless hub shifting systems. . . . . . . . . . . . . . . . . . . . . . . .70
7.3.3 Derailleur/hub shifting system (Dual Drive) . . . . . . . . . . . . . . . . .70
8 Pinion gearbox ................................... . 71
8.1 Before every ride . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
8.2 Shifting gears with a Pinion gearbox . . . . . . . . . . . . . . . . . . 72
8.3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
8.4 Cleaning a Pinion gearbox. . . . . . . . . . . . . . . . . . . . . . . . 74
8.5 Maintaining a Pinion gearbox . . . . . . . . . . . . . . . . . . . . . . 74
8.5.1 Maintaining a Pinion gearbox with a chain drive . . . . . . . . . . . . . .75
8.5.2 Maintaining a Pinion gearbox with a belt drive . . . . . . . . . . . . . . .75
8.6 Oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
9 Belt drive ........................................ . 76
9.1 Belt drive structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.2 Using the belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.3 Checking the belt tension . . . . . . . . . . . . . . . . . . . . . . . . 77
9.4 Belt drive wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.4.1 Visually inspecting the belt for wear . . . . . . . . . . . . . . . . . . . .77
9.4.2 Visually inspecting the belt drive for wear . . . . . . . . . . . . . . . . .78
9.4.3 Visually inspecting the chainring for wear . . . . . . . . . . . . . . . . .78
9.5 Cleaning the belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . 79
10 Wheels and tyres................................. . 79
10.1 Tyres and valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
10.1.1 Valve types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
10.1.2 Tyre pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
10.2 Rims and spokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
10.3 Fitting and removing the front/rear wheel . . . . . . . . . . . . . . . 83
10.3.1 Front/rear wheels with quick-release axles . . . . . . . . . . . . . . . .86
10.3.1.1 Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
10.3.1.2 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
10.3.2 Front/rear wheels with conventional thru-axles . . . . . . . . . . . . . .87
10.3.2.1 Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
10.3.2.2 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Cycle
10.3.3 Front/rear wheels with lever-type thru-axles . . . . . . . . . . . . . . .88
10.3.3.1 Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
10.3.3.2 Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
10.3.4 Carbon wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
11 Telescopic seat post .............................. . 91
11.1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
11.2 Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
11.2.1 Adjusting the cable tension . . . . . . . . . . . . . . . . . . . . . . . .92
11.2.2 Adjusting the extension speed. . . . . . . . . . . . . . . . . . . . . . .92
11.2.3 Telescopic seat post remote control position . . . . . . . . . . . . . . .92
11.2.4 Adjusting a pneumatic telescopic seat post . . . . . . . . . . . . . . .93
11.2.5 Bleeding a hydraulic telescopic seat post. . . . . . . . . . . . . . . . .93
11.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
12 Suspension ..................................... . 93
12.1 Suspension seat post. . . . . . . . . . . . . . . . . . . . . . . . . . 94
12.2 Suspension fork and rear suspension . . . . . . . . . . . . . . . . . 94
12.2.1 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
12.2.2 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
12.2.2.1 Compression and rebound . . . . . . . . . . . . . . . . . . . . . .95
12.2.2.2 Sag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
12.2.2.3 Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
12.2.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
13 Cleaning ....................................... . 98
13.1 Brakes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
13.2 Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
13.3 Gear shifting system . . . . . . . . . . . . . . . . . . . . . . . . . 101
13.4 Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
14 Maintenance .................................... 102*
14.1 Inspection intervals . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14.2 Screw joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
14.3 Frame and rigid fork . . . . . . . . . . . . . . . . . . . . . . . . . 105
14.4 Suspension fork. . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
14.5 Luggage carrier and mudguards . . . . . . . . . . . . . . . . . . . 106
14.6 Saddle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
14.7 Handlebars and handlebar stems . . . . . . . . . . . . . . . . . . 106
Cycle
14.8 Adjusting the headset . . . . . . . . . . . . . . . . . . . . . . . . 107
14.8.1
Conventional handlebar stem with an internal clamping mechanism. . . . . . 108
14.8.2 Handlebar stem with an external clamping mechanism . . . . . . . . 108
14.9 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
14.9.1 Rims and spokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
14.9.2 Rim wear indicator with rim brakes . . . . . . . . . . . . . . . . . . . 110
14.9.3 Tyres. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
14.10 Flat tyre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
14.11 Removing the wheel. . . . . . . . . . . . . . . . . . . . . . . . . 111
14.11.1 Preparing the brakes . . . . . . . . . . . . . . . . . . . . . . . . . . 111
14.11.1.1 Preparing mechanical rim brakes. . . . . . . . . . . . . . . . . 112
14.11.1.2 Preparing hydraulic rim brakes . . . . . . . . . . . . . . . . . . 113
14.11.1.3 Preparing the coaster brake . . . . . . . . . . . . . . . . . . . 113
14.11.1.4 Preparing the brakes on racing bikes . . . . . . . . . . . . . . 114
14.11.2 Removing the front wheel. . . . . . . . . . . . . . . . . . . . . . . . 114
14.11.3 Removing the rear wheel . . . . . . . . . . . . . . . . . . . . . . . . 114
14.11.4 Removing clincher or folding tyres . . . . . . . . . . . . . . . . . . . 115
14.11.5 Checking the rim tape. . . . . . . . . . . . . . . . . . . . . . . . . . 117
14.11.6 Fitting clincher or folding tyres . . . . . . . . . . . . . . . . . . . . . 117
14.11.7 Fitting UST tyres. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
14.11.8 Fitting the wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
14.11.8.1 Fitting the front wheel . . . . . . . . . . . . . . . . . . . . . . . 120
14.11.8.2 Fitting the rear wheel . . . . . . . . . . . . . . . . . . . . . . . 120
14.11.8.3 After fitting the wheels . . . . . . . . . . . . . . . . . . . . . . 121
14.12 Brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
14.12.1 Rim brakes in general . . . . . . . . . . . . . . . . . . . . . . . . . . 123
14.12.1.1 Checking a brake pad . . . . . . . . . . . . . . . . . . . . . . . 123
14.12.1.2 Changing a brake pad. . . . . . . . . . . . . . . . . . . . . . . 124
14.12.1.3 Changing a screw-type brake pad . . . . . . . . . . . . . . . . 125
14.12.1.4 Changing a brake pad with a fixing pin. . . . . . . . . . . . . . 125
14.12.1.5 Changing the brake block holders on a racing bike . . . . . . . 125
14.12.1.6 Adjusting brake pad distance on a racing bike . . . . . . . . . 127
14.12.2 Mechanical rim brake . . . . . . . . . . . . . . . . . . . . . . . . . . 128
14.12.2.1 Changing a brake block holder . . . . . . . . . . . . . . . . . . 128
14.12.2.2 Adjusting the brake block holder distance . . . . . . . . . . . . 130
14.12.2.3 Checking the brake system . . . . . . . . . . . . . . . . . . . . 130
Cycle
14.12.3 Hydraulic rim brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
14.12.3.1 Changing the brake block holders . . . . . . . . . . . . . . . . 131
14.12.3.2 Adjusting brake block holder distances (Magura HS models) . . 132
14.12.3.3 Checking the brake system . . . . . . . . . . . . . . . . . . . . 133
14.12.4 Disc brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
14.12.4.1 Bedding in a disc brake . . . . . . . . . . . . . . . . . . . . . . 134
14.12.4.2 Checking the brake disc . . . . . . . . . . . . . . . . . . . . . 134
14.12.4.3 Adjusting the pressure point . . . . . . . . . . . . . . . . . . . 134
14.12.4.4 Adjusting the brake calliper . . . . . . . . . . . . . . . . . . . . 134
14.12.4.5 Changing brake pads . . . . . . . . . . . . . . . . . . . . . . . 135
14.12.4.6 Checking a brake pad . . . . . . . . . . . . . . . . . . . . . . . 137
14.12.4.7 Checking the brake system . . . . . . . . . . . . . . . . . . . . 137
14.12.5 Coaster brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
14.13 Crankset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
14.14 Lighting set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
14.15 Hub dynamo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
14.16 Chain tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
14.16.1 Chain tension in derailleur shifting systems . . . . . . . . . . . . . . 140
14.16.2 Shift cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
14.16.3 Derailleur shifting system . . . . . . . . . . . . . . . . . . . . . . . . 140
14.17 Tyre pressure recommendations . . . . . . . . . . . . . . . . . . 141
14.18 Greasing and oiling . . . . . . . . . . . . . . . . . . . . . . . . . 142
14.19 Cleaning and maintenance schedule . . . . . . . . . . . . . . . . 142
15 Storage ........................................ 145
16 Warranty ....................................... 145
17 Guarantee ...................................... 146
18 Disposal ........................................ 147
18.1 Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
18.2 Electronic components and accessories . . . . . . . . . . . . . . 147
18.3 Packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
18.4 Tyres and inner tubes. . . . . . . . . . . . . . . . . . . . . . . . . 147
18.5 Lubricants and care products . . . . . . . . . . . . . . . . . . . . 147
*Chapters where additional information is available to you in the online
user manual
can be identified by the blue underlined text, such as:
5.2 Adjustments.
Cycle Basics
1
1 Basics
1.1 Reading and storing the user manual
This user manual is part of your cycle. The cycle user manual refers to bikes,
racing bikes, pedelecs, S-pedelecs, children’s bikes and balance bikes
collectively as cycles. The user manual contains important information about
adjustment and use. Read the entire user manual carefully, paying particular
attention to the safety notes, before using the cycle. Also carefully and
thoroughly read the supplementary user manuals depending on the cycle
model and cycle category. Failure to follow this user manual may result in
serious injury or damage to the cycle. Keep the user manual to hand.
If passing the cycle on to a third party, it is essential that you include this user
manual along with it.
1.2 Proper use
Neither the manufacturer nor the dealer accept any liability for damage caused due to
improper use. Use the cycle only as described in this user manual. Any other use is
deemed improper and may result in accidents, serious injury or damage to the cycle.
Converting a cycle into a pedelec or S-pedelec through retrofitting is not permitted.
Tampering with the drive unit of a pedelec or S-pedelec is prohibited. Improper use of
the cycle will invalidate the guarantee (see the “Warranty” chapter).
The cycle is designed for use by one person, with the seating position adjusted to suit
their height (see the “Basics / Seating position” chapter).
Child seats, child trailers or other bike trailers (cargo or dog trailers) are only permitted for
use with category 2 and category 3 cycles
(see the “Basics / Cycle categories” chapter),
excluding children’s and junior bikes with 20" and 24" wheels.
The exceptions to this are:
Cycles with carbon frames
S-pedelec cycles
Cycles with full-suspension frames must have the latest generation of rear frame bolts
with circlips (generally installed as standard in models from 2017 onwards).
Read the “Safety / Notes on carrying children” chapter for more information.
Contact your dealer before using child trailers or child seats.
Racing bikes and fitness bikes are designed solely for use on roads and paths with a
smooth asphalt, concrete or paved surface. Any use on unsurfaced paths may cause
the cycle to break down. Luggage carriers, child seats or bike trailers may not be fitted.
CycleBasics
2
A racing bike/fitness bike is defined as a cycle
with drop handlebars (racing bike) or flat handlebars (flat bar on a fitness bike)
with a tyre width of up to 32 mm/1.3"
with a rigid frame
which requires a stretched out seating position, as in cycle sports
Proper use of the cycle on the road requires you to know, understand and observe
national and regional regulations (see the “Safety / Notes on road use” chapter).
1.3 Cycle categories
The cycle is marked with a cycle category symbol. This symbol is generally located on
the left-hand side of the seat tube:
x Check the category indicated on your cycle against the cycle categories in the
table below.
x Read all the chapters that are relevant to your cycle category.
Symbol Cycle category Use
Category 0 cycles are generally
12" balance bikes and 12" or 16"
children’s bikes.
Category 0:
- For children aged 3 years and up
- Only for use under the supervision of a
parent or guardian
- Not permitted on the road
- Not permitted in competitions
- Not suitable for jumps or acrobatics
Category 1 cycles are generally
bikes, pedelecs and S-pedelecs
in the style of racing bikes or
fitness bikes (urban bikes).
Category 1:
- Solely for asphalt, concrete or paved roads
and paths
- Wheels must be kept in permanent contact
with the ground
- Permitted in competitions
- Not suitable for drops, jumps or acrobatics
Category 2 cycles are generally
bikes, pedelecs and S-pedelecs
in the style of city, trekking,
cross-trekking or cargo bikes,
plus 24" junior bikes and 20"
children’s bikes.
Category 2:
- Includes category 1, plus surfaced and
naturally firm paths with moderate inclines
- Can be ridden down steps of up to
15 cm/5.9", e.g. kerbs
- Not permitted in competitions
- Not suitable for jumps or acrobatics
Cycle Basics
3
Symbol Cycle category Use
Category 3 cycles are generally
bikes, pedelecs and S-pedelecs
in the style of mountain bikes
designed for cross-country,
marathon and touring use, plus
bikes in the cyclo-cross and
all-track segments.
Category 3:
- Includes categories 1 and 2, plus rough
trails with small obstacles, and unsurfaced
routes that require good riding technique
- Permitted in competitions
- Drops and jumps permitted up to a max.
height of 60 cm/23.6" (with appropriate
riding technique)
- Not suitable for acrobatics
Category 4 cycles are generally
bikes, pedelecs and S-pedelecs
in the style of mountain bikes
designed for all-mountain use.
Category 4:
- Includes categories 1, 2 and 3
- Larger obstacles and higher speeds require
increased riding skill
- Permitted in competitions
- Drops and jumps permitted up to a max.
height of 120 cm/47.2" (with appropriate
riding technique)
- Not suitable for acrobatics
Category 5 cycles are generally
bikes, pedelecs and S-pedelecs
in the style of mountain bikes
designed for enduro/freeride/
downhill use.
Category 5:
- Includes categories 1, 2, 3 and 4, plus
very fast and very demanding terrain with
extreme inclines
- Very high demands on riding skill
- Permitted in competitions
- Long drops and jumps permitted (with
appropriate riding technique)
- Not suitable for acrobatics
CycleBasics
4
1.4 Maximum gross weight limit
DANGER
Component breakage due to overloading the cycle.
Risk of accident and injury!
x Observe the maximum gross weight limit for the cycle.
NOTE
Material damage due to overloading the cycle.
Risk of damage!
x Observe the maximum gross weight limit for the cycle.
The cycle has a maximum gross weight limit that may not be exceeded.
x Observe the maximum gross weight limit for the cycle.
x Contact your dealer if you have any questions about the maximum gross weight
limit.
This symbol is only applicable for Europe:
This symbol (example) indicates the maximum gross weight limit for the
cycle. Refer to the sticker on your cycle to find out its maximum gross
weight limit. The sticker is generally located on the lower left-hand side of
the seat tube.
This symbol is only applicable for the USA:
This symbol (example) indicates the maximum gross weight limit for the
cycle. Refer to the sticker on your cycle to find out its maximum gross
weight limit. The sticker is generally located on the lower left-hand side of
the seat tube.
The maximum gross weight limit is calculated as follows: cycle + rider + luggage/
backpack/child seat etc. = maximum gross weight.
285 lbs
Cycle Basics
5
1.5 Seating position
CAUTION
Muscle tension and joint pain due to an incorrectly adjusted
seating position.
Risk of injury!
x Have the seating position correctly adjusted by your dealer.
CAUTION
Limited ability to reach controls due to an incorrectly adjusted
seating position.
Risk of accident and injury!
x Have the seating position correctly adjusted by your dealer.
The optimum seating position depends on the size and shape of the cycle frame, the
size of the rider, and how the handlebars and saddle are adjusted. Optimum seating
position adjustments require expertise.
The optimum seating position can also depend on how the cycle is used, e.g. primarily
for sports.
The main characteristics of an optimum seating position are:
When one pedal is up, the arms and the top knee are all at a 90° angle.
The lower leg is slightly bent (see “Illustr.: Optimum seating position (A)”).
When one pedal is forward, the knee is over the axle of the front pedal
(see “Illustr.: Optimum seating position (B)”).
The arms are relaxed and bent slightly outwards (not visible in the picture).
The back is leant slightly forwards, not vertical to the seat post.
CycleBasics
6
90°
90°
90°
A B
Illustr.: Optimum seating position (example)
x Read the “Basic adjustments / Saddle” and “Basic adjustments / Handlebars and
handlebar stems” chapters on adjusting the saddle or handlebars to the correct height.
1.6 Frame height
For a safe and comfortable ride, it is important to buy a cycle with the right height and
length of frame for the rider. The right frame height depends on the rider’s inside leg (inseam)
measurement. It is important to take the inside leg measurement into account so that it is
possible to quickly and safely stop the cycle and dismount in dangerous situations.
x Consult a dealer about the right frame height.
1.7 Helmet
x Wear a suitable and correctly fitting helmet every time you ride your cycle.
x Consult your dealer when buying a helmet.
x Have your dealer adjust your helmet to fit you.
x Refer to and follow the information enclosed by the helmet manufacturer.
x Ensure that the helmet is correctly positioned (see “Illustr.: Helmet position (A)”).
x Always fasten the clasp under your chin.
A B
Illustr.: Helmet position ((A) correct, (B) sitting too far back) (example)
Cycle Basics
7
1.8 Luggage carrier
NOTE
Overloading the luggage carrier.
Risk of damage!
x Observe the maximum load limit for the luggage carrier.
x The luggage carrier is for transporting luggage only;
transportation of people is not allowed.
NOTE
Damage to cycle components due to fitting a luggage carrier
where this is not permitted.
Risk of damage!
x Never fit a luggage carrier to the seat post.
x Never fit a luggage carrier on a full-suspension frame.
A luggage carrier is a device on the cycle which can be used to transport luggage.
Depending on the cycle model, it may be a luggage carrier with a clamp, a luggage
carrier with bungee cords and no clamp, or a low-rider luggage carrier for panniers.
Many models also come equipped as standard with luggage system carriers. There are
a variety of accessories available for these luggage system carriers, such as baskets or
bags that lock in place on the luggage area.
x Consult your dealer about suitable accessories.
If your cycle is equipped with a luggage carrier:
x Do not make any alterations to the luggage carrier.
x Consult your dealer if you would like to replace the luggage carrier.
x Do not overload the luggage carrier.
x Observe the maximum load limit for the luggage carrier.
x The maximum load limit is generally stamped on the surface of the luggage carrier.
x If the maximum load limit is not stamped on the surface of the luggage carrier,
consult your dealer.
CycleBasics
8
x Load the luggage carrier evenly.
x If you use panniers, ensure that the weight of the luggage is distributed equally
between the left and right-hand sides.
x Make sure that the luggage is adequately secured to prevent it falling off.
x Use bungee cords to secure luggage if necessary.
If your cycle is not equipped with a luggage carrier:
x Ask your dealer whether your cycle is suitable for a luggage carrier if you would like
to retrofit one.
x Have the luggage carrier fitted by your dealer.
1.8.1 Luggage carrier with clamp
1. Grasp the clamp, carefully pull it
upwards and hold it in this position.
2. Place your luggage on the luggage
carrier.
3. Fasten your luggage on the luggage
carrier by slowly lowering the clamp.
1.8.2 Luggage carrier with bungee cord and no clamp
1. Release the bungee cords.
2. Place your luggage on the luggage carrier.
3. Pull the bungee cords firmly over the
luggage.
4. Fasten the bungee cords to the
attachments provided on the frame of
the luggage carrier.
x Make sure that the luggage is
secured to prevent it falling off.
Illustr.: Luggage carrier with a clamp (example)
Illustr.: Luggage carrier with bungee cords
(example)
Cycle Basics
9
1.8.3 Low-rider luggage carrier for panniers
1. Fill the panniers.
2. Ensure that the panniers are of equal
weight.
3. Close the panniers so that there are no
dangling straps or buckles.
4. Mount the panniers on the luggage
carrier using the hanger.
x Make sure that the bags are firmly
in place on the low-rider luggage
carrier and secured to prevent them
falling off.
1.8.4 Luggage system carrier
x Refer to and follow the information enclosed about the features of your luggage
system carrier.
x If necessary, consult your dealer about features and suitable accessories.
1.9 Kickstand variants
A kickstand is a device for parking the cycle
in an upright position after use.
Kickstand-equipped models have a central
side kickstand, a central bipod kickstand
or a rear kickstand (see “Illustr.: Kickstand
variants”).
If your cycle is not equipped with a kickstand
and you would like to have one retrofitted:
x Consult your dealer about retrofitting a
kickstand.
x Have the kickstand fitted by your dealer.
x Note that retrofitted kickstands are not
permitted on carbon frames.
Illustr.: Low-rider luggage carrier (example)
2
3
1
Illustr.: Kickstand variants (example)
1 Central bipod kickstand
2 Central side kickstand
3 Rear kickstand
CycleBasics
10
1.9.1 Side kickstand and rear kickstand
1. To flip down the central side kickstand or rear kickstand, hold the cycle firmly.
2. Push the side or rear kickstand downwards with your foot.
3. Set the cycle on the side or rear kickstand.
4. Before letting go of the cycle, make sure that it is stable on the side or rear
kickstand and cannot fall over.
x To flip the side or rear kickstand up again, take the weight off it and push it
upwards with your foot.
1.9.2 Bipod kickstand
1. To flip down the central bipod kickstand, hold the cycle firmly.
2. Push the bipod kickstand downwards with your foot.
3. Fix the bipod kickstand in place with your foot.
4. Push the cycle backwards so that it sits on the bipod kickstand.
5. Before letting go of the cycle, make sure that it is stable on the bipod kickstand
and cannot fall over.
x To flip the bipod kickstand up, push the cycle forwards. This movement will push
the bipod kickstand upwards.
x Before riding off, check that the kickstand is fully up and not dragging on the
ground.
Cycle Basics
11
1.10 Aero handlebars on racing bikes
WARNING
Longer braking distance due to greater distance from the brake
levers.
Risk of accident!
x Familiarise yourself with the aero handlebars and the change
of grip required to reach the brake levers.
x Take particular care to look ahead and anticipate while riding
if you use aero handlebars.
“Aero” handlebars are used to allow aerodynamic positioning on a racing
bike, for example in triathlons and time trials.
Only category 1 cycles and racing bikes without motor assistance may be
retrofitted with aero handlebars.
The shift levers on aero handlebars are often
at the ends of the bars (see the “Derailleur
shifting system / Operation / Operating the
shift levers on a racing bike” chapter). The
brake levers are at the ends of the standard
handlebars. When the racing bike is ridden in
an aerodynamic position, the brake levers
are out of the rider’s immediate reach.
x Keep off the road while you familiarise
yourself with the handling of aero
handlebars and the change of grip
required to reach the brake levers.
x When practising with the handlebars,
eliminate other potential hazards such
as inexperienced use of clipless pedals.
Limit yourself to practising with the handlebars at first.
x Adapt your riding style to suit the altered handling characteristics.
1
2
Illustr.: Distance between the shift levers
and brake levers on aero handlebars
(example)
1 Shift lever
2 Brake lever
CycleBefore setting off
12
2 Before setting off
This chapter contains information about how to put the cycle into use.
2.1 Before every ride
WARNING
Material breakage due to usage-related wear and loose screw
joints.
Risk of accident and injury!
x Check the cycle according to the inspection instructions
before every ride.
x Only use the cycle if it is undamaged.
x Only use the cycle if you find no signs of excessive wear and
no loose screw or clip-type joints.
x Check the cycle according to the inspection instructions before every ride.
Inspection instructions
Screw and clip-type joints Visually inspect screw and clip-type joints
Brakes Test brake functionality
Gear shifting system Test gear shifting system functionality
Wheels Visually inspect for correct positioning and alignment
Visually inspect thru-axles, quick releases and/or screw
joints
Tyres Visually inspect tyres for cracks or foreign bodies
Check and adjust tyre pressure
Frame Visually inspect frame for cracks, deformation or discol-
ouration
Suspension Test functionality by compressing and extending
Rims and spokes Visually inspect rims and spokes
Quick releases Check preload
Visually inspect quick releases for correct positioning
Saddle/seat post Visually inspect saddle/seat post
Cycle Before setting off
13
Inspection instructions
Handlebars/handlebar stem Check handlebars and handlebar stem are firmly in place
Visually inspect handlebars and handlebar stem for
cracks, deformation or discolouration
Lighting Test lighting functionality
Bell Test bell functionality
1. With brakes that have quick-release
levers, check both brakes to see
whether these levers are open
(see “Illustr.: Quick-release lever position”).
2. Test the functionality of the brakes.
x Operate the brake levers, and
coaster brake if applicable, and
listen for unusual noises.
x Check that the cycle is difficult or
impossible to push with the brake
applied.
x Check whether there is any brake pad grinding when the brake levers are
released.
x When operating the brake levers, check whether they touch the handlebars.
If necessary, have your dealer readjust the brakes or replace worn components.
3. Test the functionality of the gear shifting system.
x Check that all the gears shift correctly and whether any unusual noises are
produced in the process.
4. Compress and extend the suspension fork.
x If you hear unusual noises or the suspension fork gives way without any
resistance, have it checked by your dealer.
5. Check whether the quick-release axles or thru-axles, if applicable, are correctly
fastened and adjusted (see the “Wheels and tyres / Fitting and removing the front/
rear wheel” chapter).
6. Check whether the handlebars are aligned perpendicularly to the front wheel.
x Adjust the handlebars if they are not perpendicular to the front wheel
(see the “Basic adjustments / Handlebars and handlebar stems / Aligning the
handlebars” chapter).
7. Test the functionality of the bell and lighting.
x Check whether you hear a clear sound when you operate the bell.
Illustr.: Quick-release lever position (example)
1 Quick-release lever
1
1
CycleBefore setting off
14
x Switch on the lighting and check whether the headlamp and rear lamp are
lit (see the “Basic adjustments / Lighting” chapter). With dynamo-equipped
cycles, turn the front wheel to do this.
2.2 Before the first ride
WARNING
Unexpected cycle behaviour due to incorrect operation.
Risk of accident and injury!
x Familiarise yourself with the cycle before riding it for the first
time.
The cycle has been fully assembled and adjusted by your dealer, and is ready to ride.
The following points must also be noted before your first ride:
x Familiarise yourself with the arrangement of the brake levers.
x If the brake levers for the front and rear brakes are arranged in a way that is
unusual to you, have this changed by your dealer.
x Stay at low speeds while you get accustomed to the braking characteristics of
your brake type (see the “Brake” chapter).
x With hydraulic brakes, operate both brake levers several times to centre the brake
pads in the brake calliper.
x Keep off the road while you get accustomed to the handling characteristics of your
cycle.
x Keep off the road while you practice using the gear shifting system until you can
operate it without any loss of attention (see the “Derailleur shifting system” and
“Hub shifting systems” chapters).
x Check that you can sit in a position which is comfortable on longer rides and
allows you to reach all the components on the handlebars safely while riding
(see the “Basics / Seating position” chapter).
Cycle Safety
15
3 Safety
3.1 General safety notes
DANGER
Lack of protective headgear.
Risk of injury!
x Wear a suitable helmet when riding.
WARNING
Incorrect operation of the cycle due to insufficient knowledge.
Risk of accident and injury!
x Familiarise yourself with the features of the cycle before
operation and use.
WARNING
Incorrect operation by children or people with insufficient
knowledge or capabilities.
Risk of accident and injury!
x Do not allow the cycle to be used by people with reduced
physical, sensory or mental capabilities or with a lack of
experience and expertise.
x Do not allow children to play with the cycle. Do not allow
cleaning or maintenance to be carried out by children or
people with reduced physical, sensory or mental capabilities.
x Do not allow children to play with the packaging or small
parts.
CycleSafety
16
The following safety note is only applicable to these cycle categories:
WARNING
Component breakage due to improper use of the cycle.
Risk of accident and injury!
x Do not jump over ramps or mounds of earth with the cycle.
x Do not ride the cycle cross-country.
x Do not ride the cycle over stairs, rocks, or any other steps
(such as kerbs) that are more than 15 cm/5.9" high.
The following safety note is only applicable to these cycle categories:
WARNING
Component breakage due to improper use of the cycle.
Risk of accident and injury!
x Only use the cycle to tackle obstacles that your skill and
experience allow.
Cycle Safety
17
WARNING
Improper additions or alterations to the cycle and incorrect
accessories can cause the cycle to malfunction.
Risk of accident and injury!
x Have your dealer carry out alterations to the cycle.
x Ask your dealer about suitable accessories.
x Have child seats or child trailers fitted by your dealer only.
x Only have child seats or any type of trailer fitted after
consulting your dealer and if permitted by the cycle category
or specifications for your model.
WARNING
Longer braking distance and reduced traction due to slippery or
dirty roads.
Risk of accident and injury!
x Adapt your riding style and speed to suit the weather and
road conditions.
CAUTION
Lack of control over the cycle due to riding freehand.
Risk of accident and injury!
x Never ride the cycle freehand.
CycleSafety
18
CAUTION
Pinching hazards on the cycle.
Risk of accident and injury!
x Ensure that items of clothing cannot become entangled. Wear
suitable clothing.
CAUTION
Slipping due to improper footwear.
Risk of accident and injury!
x Wear non-slip shoes with hard soles.
CAUTION
Inadequate protective clothing.
Risk of injury!
x Wear appropriate protective clothing (e.g. protectors and gloves)
depending on your cycle category and its intended use.
NOTE
Increased wear due to operating the cycle incorrectly.
Risk of damage!
x Use your cycle as described in the section on proper use.
x Refer to the notes on use that are relevant to your cycle
category.
x Do not overload your cycle. Only tackle terrain or roads that
are appropriate for your cycle category.
Cycle Safety
19
3.2 Notes on road use
DANGER
Poor visibility to other road users.
Risk of accident and injury!
x Wear light-coloured clothing with reflective elements when
riding.
WARNING
Incorrect or improper use.
Risk of accident and injury!
x Refer to and follow national and regional road regulations.
x Only use the cycle on the road if its equipment meets national
and regional road regulations.
x Note what is proper use for your cycle category.
WARNING
Inattention on the road.
Risk of accident and injury!
x Do not get distracted by other activities while riding, e.g.
switching on lights.
x Do not use mobile devices such as smartphones or MP3
players while riding.
x Do not use drink bottles while riding.
x Do not ride the cycle if you have consumed alcohol,
intoxicants, or medication that could affect your riding.
CycleSafety
20
x Acquaint yourself with national and regional equipment regulations before your first ride.
For example:
Compulsory helmet use
Compulsory use of reflective safety vests
Brakes
Lighting and reflectors
Bell
Child trailers and child seats
x Only use child trailers if your cycle is suitable for child trailer use
(see the “Safety / Notes on carrying children / Child trailer” chapter).
x Only use child seats if your cycle is suitable for child seat use
(see the “Safety / Notes on carrying children / Child seat” chapter).
x Refer to and follow national and regional road regulations.
x Refer to and follow the traffic code.
x Contact your dealer if you have any questions.
Laws and regulations can change at any time. Regularly acquaint yourself
with national and regional regulations.
3.3 Notes on carrying children
DANGER
Component breakage due to overloading the cycle.
Risk of accident and injury!
x Observe the maximum gross weight limit for the cycle.
x Have a child seat or child trailer fitted by your dealer.
CAUTION
Risk of burning due to hot brake discs.
Risk of injury!
x Do not allow your child to play near the cycle.
Cycle Safety
21
CAUTION
Injury to your child due to the cycle falling over.
Risk of injury!
x When parking, always hold the cycle firmly while your child is
sitting in the child seat or while they are near the cycle.
x Do not allow your child to play unsupervised near the parked
cycle.
x Never leave your child sitting in the child seat or child trailer
when you park the cycle on the kickstand.
NOTE
Material damage due to overloading the cycle.
Risk of damage!
x Observe the maximum gross weight limit for the cycle.
Child seats, child trailers or other bike trailers (cargo or dog trailers) are only permitted for
use with category 2 and category 3 cycles
(see the “Basics / Cycle categories” chapter),
excluding children’s and junior bikes with 20" and 24" wheels. The exceptions to this are:
Cycles with carbon frames
S-pedelec cycles
Cycles with full-suspension frames must have the latest generation of rear frame bolts
with circlips (generally installed as standard in models from 2017 onwards).
The following points must be noted before carrying children:
x Only carry a child in the child seat or child trailer if permitted to do so by national
and regional regulations.
x Refer to and follow national and regional regulations on the use of child seats and
child trailers.
x Ask a dealer about suitable child seats and child trailers.
x Have child seats and child trailers fitted by your dealer only.
x Refer to and follow the information enclosed by the child seat or child trailer
manufacturer.
CycleSafety
22
x Observe the maximum weight limit for the child seat or child trailer, as stated in the
accompanying user manual.
x Keep off the road while you get accustomed to the altered handling and braking
behaviour of your cycle with a child seat or child trailer.
x Adapt your riding style to suit the altered handling characteristics.
x Practice with your child how to behave while riding.
x Only carry a child in the child seat or child trailer if they are wearing a fitted helmet.
Consult a dealer about choosing a suitable helmet.
3.3.1 Child seat
CAUTION
Injury to your child due to inadequate safeguards.
Risk of injury!
x When fitting a child seat, have the saddle springs completely
covered to avoid injury.
x When fitting a child seat, have all revolving and moving parts
covered, e.g. with a spoke protector.
NOTE
Damage to cycle components due to fitting a child seat where
this is not permitted.
Risk of damage!
x Never fit a child seat to the handlebars.
x Never fit a child seat to the seat post.
x Never fit a child seat to a carbon frame.
Cycle Safety
23
A child seat is a system for carrying small
children on the cycle (see “Illustr.: Child seat”).
The following points must be noted when using a child seat:
x Only have child seats fitted if your cycle is suitable for this (see the “Basics / Proper
use” chapter). Consult your dealer about suitable child seats.
x Only use child seats which are installed so that the child sits behind the rider.
From a design perspective, not all cycles are able to have child seats fitted.
The user and fitting instructions provided by the child seat manufacturer
must be followed. With full-suspension frames, the suspension system
tuning must be checked. Consult your dealer.
3.3.2 Child trailer
A child trailer is a system for carrying small
children, and is hitched behind the cycle
(see “Illustr.: Child trailer”).
The following points must be noted when using a child trailer:
x Only have child trailers fitted if your cycle is suitable for this (see the “Basics /
Proper use” chapter). Consult your dealer about suitable child trailers.
x Observe the maximum trailer load limit:
The maximum trailer load limit for an unbraked child trailer is 40 kg/88 lbs.
The maximum trailer load limit for a braked child trailer is 80 kg/176 lbs.
x Note that a child trailer makes your cycle significantly longer.
x Only carry the approved number of children for your child trailer.
x Only use child trailers with functional lighting that meets national and regional
regulations.
x Choose a child trailer with a restraint feature.
Illustr.: Child seat (example)
Illustr.: Child trailer (example)
CycleSafety
24
x Have the child trailer fitted with a flexible flagpole (at least 1.5 m/4.9 ft high) and a
fluorescent pennant, as well as covers for the spokes and wheel wells.
From a design perspective, not all cycles are able to have trailer couplings
fitted. Consult your dealer.
3.4 Notes on transportation
3.4.1 Notes on luggage
WARNING
Falling due to incorrectly transported luggage.
Risk of accident and injury!
x Do not transport bags or other items on the handlebars.
x Secure items on the luggage carrier to prevent them slipping and
falling off. Only use undamaged bungee cords to secure luggage.
x Use sturdy panniers or suitable accessories for your luggage
system carrier.
WARNING
Altered handling characteristics due to additional weight.
Risk of accident and injury!
x Keep off the road while you familiarise yourself with the
handling characteristics when carrying additional luggage.
x Check the weight distribution of your luggage.
x Distribute additional weight centrally on the luggage carrier or
equally on both sides.
x If you realise that you have no guarantee of being able to ride
safely, reduce your luggage.
x Adapt your riding style to suit the altered handling
characteristics.
Cycle Safety
25
The following points must be noted when transporting luggage:
x Position your luggage so as not to obscure reflectors or lamps.
x Brake earlier and plan for a longer braking distance as well as more sluggish
steering behaviour.
x Secure luggage on the luggage carrier, e.g. with bungee cords, to prevent it
slipping and falling off.
x Stow heavy items so that the bulk of the weight is close to the wheel hubs,
e.g. in the bottom of panniers.
x Ensure that fasteners such as cords or rope cannot become entangled in moving parts.
3.4.2 Notes on fitting trailers
WARNING
Component breakage due to fitting the trailer coupling incorrectly.
Risk of accident and injury!
x Have trailer couplings fitted by your dealer.
x Only have trailers fitted which are fastened to the rear axle of the cycle via a trailer
coupling.
The sole exceptions to this are Winora Group cycle models which have a trailer coupling
integrated with the chain stays and are marked accordingly.
x Do not under any circumstances have the trailer coupling fastened to other parts of
the frame or components such as the seat post.
3.4.3 Notes on cargo and dog trailers
NOTE
Incorrect use of cargo and dog trailers.
Risk of damage!
x Never exceed the maximum trailer load limit.
x Secure loads and items in the trailer to prevent them slipping
and falling off.
x Only carry dogs in suitable dog trailers. Do not use a cargo or
child trailer.
CycleSafety
26
Cargo and dog trailers are systems for transporting luggage and other items, and for
carrying dogs. Cargo and dog trailers are hitched behind the cycle.
The following points must be noted when using cargo and dog trailers:
x Only have trailers fitted if your cycle is suitable for this (see the “Basics / Proper
use” chapter). Consult your dealer about suitable trailers.
x Observe the maximum trailer load limit:
The maximum trailer load limit for an unbraked trailer is 40 kg/88 lbs.
The maximum trailer load limit for a braked trailer is 80 kg/176 lbs.
x Note that a trailer makes your cycle significantly longer.
x Only use trailers with functional lighting that meets national and regional regulations.
From a design perspective, not all cycles are able to have trailer couplings
fitted. Consult your dealer.
3.4.4 Notes on transporting the cycle by car
DANGER
Endangerment of other road users due to incorrectly fastened
cycles.
Risk of accident and injury!
x If you transport your cycle using a fastening system for the
roof or rear of the car, check the cycle fastening regularly
during driving breaks to prevent it coming loose.
CAUTION
Unsecured transportation of cycles and small parts.
Risk of accident and injury!
x Never transport an unsecured cycle or unsecured cycle parts
inside your car or in the boot (trunk).
x Fix the cycle in place with suitable interior fastening systems if
you transport the cycle in the boot or inside your car.
Cycle Safety
27
NOTE
Incorrect use of bike carriers.
Risk of damage!
x Only use approved bike carriers that allow the cycle to be
transported upright.
x Consult a dealer about a suitable carrier system.
x Cycles with hydraulic disc or rim brakes must never be
transported upside down on their saddles. This may cause
the hydraulic disc or rim brakes to fail.
x Secure the cycle so that it cannot slip or fall off.
Dealers offer a variety of carrier systems for transporting the cycle by car.
x Consult your dealer about suitable carrier and fastening systems.
x Refer to and follow national and regional road regulations.
x Refer to the information enclosed by the manufacturer about fitting and use.
x In the case of carbon-component cycles, note that these components can be
damaged by clamping forces. Only use dedicated fastening systems.
x Note the change in the height of your car when using a roof carrier system.
Measure the exact height before driving off.
x Fit the transport locks on disc brakes when you transport the cycle without wheels.
x When transporting pedelecs or S-pedelecs, follow the instructions in the original
operating manual for the drive system.
3.5 Notes on torques
WARNING
Material fatigue due to tightening screw joints incorrectly.
Risk of accident and injury!
x Do not use the cycle if you find loose screw joints.
x Screw joints must be properly tightened with a torque wrench.
x Screw joints must be tightened using the correct torques.
CycleSafety
28
To correctly tighten the screw joints, the applicable torques must be observed.
This requires a torque wrench with an appropriate adjustment range.
x If you have no experience with using torque wrenches or do not own a suitable
torque wrench, have the screw joints checked by your dealer.
The correct torque for a screw joint is dependent on the material and diameter of the
screw, as well as the material and design of the component.
x If you tighten screw joints yourself, check whether your cycle is equipped with
aluminium or carbon components (see the specifications data sheet provided by
the dealer).
x Observe the specific torques for aluminium or carbon components.
x Individual components on the cycle are labelled with torque specifications or
insertion depth markings. It is essential that you follow these specifications and
markings.
3.6 Notes on screw turning directions
NOTE
Material damage due to handling screw joints incorrectly.
Risk of damage!
x Observe the turning direction of screws, thru-axles and nuts.
x Tighten screws, thru-axles and nuts by turning them clockwise.
x Loosen screws, thru-axles and nuts by turning them anticlockwise.
In the event of any deviation from this rule, the change in turning direction
will be indicated in the respective chapter. Refer to the relevant notes.
Cycle Safety
29
3.7 Notes on wear
WARNING
Malfunction due to excessive wear, material fatigue or loose
screw joints.
Risk of accident and injury!
x Check your cycle regularly.
x Do not use the cycle if you find excessive wear or loose screw
joints.
x Do not use the cycle if you find any cracks, deformation or
discolouration.
x Have the cycle checked by your dealer if you find excessive
wear or loose screw joints.
Some cycle components are consumable parts. Heavy stress and incorrect use will
increase and/or speed up wear. Different materials have distinct wear characteristics.
x Consult your dealer about cycle components that are subject to wear.
x Regularly check the state of all consumable parts (see the “Before setting off /
Before every ride” and “Maintenance” chapters).
x Clean and maintain consumable parts regularly (see the “Cleaning” and
“Maintenance” chapters).
x The following consumable parts are subject to wear in the course of proper use,
and are not covered against operational wear under the guarantee
(see the “Warranty” chapter):
Wheels (rims, spokes, hubs)
Rims in conjunction with a rim brake
Tyres
Chainrings, sprockets, bottom bracket and rear derailleur rollers
Shift and brake cables
Shift and brake cable casings
Brake pads and brake discs
Various other brake components
Handlebar tapes and handlebar grips
CycleSafety
30
Chains and drive belts
Hydraulic fluids and lubricants
Suspension element seals
Lamps
Paintwork
Saddle
Aluminium handlebars
3.8 Notes on carbon components
WARNING
Material failure due to invisible cracks after a fall.
Risk of accident and injury!
x Have carbon components checked by your dealer after
overloading or a fall, even if they are not visibly damaged.
x Have carbon components checked by your dealer at regular
intervals, even if they have not been overloaded.
x Do not use your cycle if you suspect it is damaged.
NOTE
Invisible cracks or breaks in carbon components.
Risk of damage!
x Avoid falls and severe impacts so as not to overload carbon
components.
x Never attempt to repair or straighten carbon components
yourself!
x Have carbon components checked by your dealer after
overloading.
Cycle Safety
31
NOTE
Invisible cracks or breaks in the carbon frame.
Risk of damage!
x Never retrofit a carbon frame with a kickstand.
Carbon components require specific handling and care. The following points must be
noted during maintenance, transportation or storage:
x Refer to and follow the information enclosed by the manufacturer.
x Use a torque wrench to make the correct torque adjustments.
x Never lubricate carbon components with conventional grease.
Use dedicated fitting lubricants for carbon components.
x Never expose carbon components to temperatures above 45 °C/113 °F.
x To avoid damage from falls, park your cycle carefully and in a way that prevents it
falling over.
x Never clamp a carbon frame directly in a work stand. Fit a metal seat post and
clamp this in the work stand.
x Never retrofit a carbon frame with a kickstand as this may result in damage to the
frame.
3.8.1 Falls and accidents
Carbon components can be damaged by a fall or accident. Damage to carbon
components is not always visible. Fibres or paint can peel off or be destroyed, and the
components can lose strength.
x Have carbon components replaced by your dealer after a fall or accident.
3.8.2 Bike carriers
A bike carrier is a device for transporting cycles by car. There is a risk of crushing the
carbon frame when clamping it in a bike carrier. This may result in material breakage during
subsequent use. There are dedicated bike carriers specially designed for carbon bikes.
x Ask your dealer about suitable bike carriers.
CycleSafety
32
3.8.3 Torques
Specific torques must be observed for screw joints in carbon components. Permitted
torques can be found on the respective components. Excessively high torques may result
in damage that is difficult to see. Components can break or change and cause falls.
x Refer to the fitting information enclosed by the manufacturer.
x If you lack the necessary expertise and the tools required, have torques adjusted
and checked by your dealer.
3.9 Residual risks
Even if all safety notes and warnings are observed, using the cycle still entails
unforeseeable risks such as:
Incorrect behaviour by other road users
Unforeseeable road conditions e.g. slipperiness due to black ice
Component breakage or failure due to unforeseeable material defects or material
fatigue
x Ride defensively, looking ahead and anticipating.
x Check the cycle for cracks, discolouration or damage before every ride.
x Test the functionality of safety-related components such as the brakes, lighting
and bell before every ride.
x Have the cycle checked for damage by your dealer after a fall or accident.
Cycle Basic adjustments
33
4 Basic adjustments
This chapter contains information about basic adjustments to the cycle, and information
about how to put the cycle into use.
4.1 Quick releases
NOTE
Material breakage due to handling components incorrectly.
Risk of damage!
x Only pull a quick release lever by hand. Never use tools or
other implements to pull the lever.
A quick release is a clamping device that
allows cycle components to be fitted,
removed or adjusted quickly and without
tools. An eccentric mechanism creates
tension when the quick-release lever is pulled.
Quick releases consist of two elements: the
quick-release lever and the quick-release
adjusting nut.
If no tension is created when the
quick-release lever is operated, the quick
release must be readjusted.
x Screw the quick-release adjusting nut
clockwise onto the axle until you notice
that tension is created when you pull
the quick-release lever.
Illustr.: Quick release structure (example)
1 Quick-release adjusting nut
2 Quick-release lever
A Open quick-release lever
B Closed quick-release lever
1
2
A
B
CycleBasic adjustments
34
4.2 Saddle
WARNING
Incorrect adjustment of the seat post.
Risk of accident and injury!
x Observe the minimum insertion depth for the seat post.
x If you lack the necessary expertise and the tools required to
adjust the seat post, contact your dealer.
NOTE
Material breakage due to handling components incorrectly.
Risk of damage!
x Only pull a quick release lever by hand. Never use tools or
other implements to pull the lever.
x Shortening the seat post is not permitted. This can cause the
seat tube to break or crack.
x Have the saddle adjusted by your dealer so that you can sit in a comfortable
position, easily operate all the components on the handlebars, and touch the
ground with at least the tips of your toes.
Cycle Basic adjustments
35
4.2.1 Adjusting the saddle height
The cycle may be equipped with a rigid seat post or a telescopic seat post, depending
on the model. Both types of seat post can be fastened using either a seat post clamp
with a clamp bolt, or a quick-release seat post clamp. The seat post clamp allows the
height of the saddle to be adjusted.
x For more information about telescopic seat posts, read the “Telescopic seat post”
chapter.
If your cycle has a seat post clamp with a clamp bolt:
1. Hold the saddle firmly and loosen the clamp bolt by turning it anticlockwise until
the saddle can be moved in the seat tube.
2. Pull the seat post out to the desired height.
x Follow the minimum insertion depth and minimum pull-out height
specifications.
3. Tighten the clamp bolt by turning it clockwise to fasten the seat post clamp.
x Observe the permitted torque (see the “Safety / Notes on torques” chapter).
4. Check whether the saddle is correctly positioned. It must not twist.
x If you can twist the saddle, check the seat post clamp.
If your cycle has a seat post clamp with a quick release:
1. Hold the saddle firmly and pull the
quick-release lever outwards.
2. Pull the seat post out to the desired
height.
x Follow the minimum insertion
depth and minimum pull-out height
specifications.
3. Fasten the seat post clamp by pulling
the quick-release lever inwards until it
touches the seat tube.
x If you cannot pull the clamping lever
by hand, then the preload is too high.
Correct the preload by loosening the adjustment screw a little and pull the
clamping lever again.
4. Check whether the saddle is correctly positioned. It must not twist.
x If you can twist the saddle, the preload is too low. Correct the preload by
tightening the adjustment screw a little.
Illustr.: Quick release (example)
1 Adjustment screw
2 Quick-release lever
2
1
CycleBasic adjustments
36
4.2.2 Minimum insertion depth
Seat posts have a minimum insertion depth marked on their tubing, and must be
inserted up to at least this point in the seat tube.
WARNING
Cracking or breakage to the seat tube due to shortening the seat post.
Risk of accident and injury!
x Observe the minimum insertion depth for the seat post.
x Never shorten the seat post.
x Observe the minimum insertion depth
for the seat post. The marking on the
seat post must not be visible
(see “Illustr.: Seat post minimum
insertion depth”).
x Have the saddle height adjusted by your
dealer.
4.2.3 Adjusting the minimum pull-out height
The minimum pull-out height is the minimum height to which the seat post must be pulled out
of the seat tube. This chapter applies to S-pedelecs and cycles with telescopic seat posts.
NOTE
Failure to observe the minimum pull-out height.
Risk of damage!
x Adjust the height of the saddle so as not to damage any
cables or connecting wires inside the seat tube.
x With S-pedelecs, pull the seat post out far enough that the
lighting components are not obscured by any license plate
which may be fitted to the saddle.
Illustr.: Seat post minimum insertion depth
(example)
1 Seat post clamp
2 Minimum insertion depth marking
1
2
Cycle Basic adjustments
37
If the cycle is equipped with a telescopic seat post:
x Refer to and follow information from the manufacturer.
x Have your dealer adjust the saddle height and give you instructions on operation.
4.2.4 Adjusting the saddle tilt
The saddle tilt must be adjusted to prevent your weight being supported on the
handlebars. The optimum saddle position is horizontal.
1. Loosen the saddle clamp bolt(s) under the saddle.
2. Adjust the saddle tilt. Ensure that the tilt angle adjustment mechanism is correctly
locked in place.
3. Tighten the saddle clamp bolt(s) by screwing clockwise, using the recommended
torque.
x If you lack the necessary expertise and the tools required, have the saddle tilt
adjusted by your dealer.
4.2.5 Adjusting the reach
The seating position must be adapted to suit the size of the rider. To do this, the distance
between the saddle and handlebars can be increased or decreased by moving the
saddle horizontally.
1. Loosen the saddle clamp bolt(s) under the saddle.
2. Adjust the reach. When doing so, observe the clamping range which is generally
marked on the saddle rails.
x To shorten the reach, push the saddle towards the handlebars.
x To lengthen the reach, push the saddle towards the rear wheel.
3. Tighten the saddle clamp bolt(s) by screwing clockwise, using the recommended
torque.
x If you lack the necessary expertise and the tools required, have the reach adjusted
by your dealer.
CycleBasic adjustments
38
4.3 Handlebars and handlebar stems
WARNING
Material breakage due to adjusting the handlebar height
incorrectly.
Risk of accident and injury!
x Have the handlebars adjusted by your dealer.
x Do not make any adjustments to the handlebars if you lack
the necessary expertise and the tools required.
x Observe the minimum insertion depth for the handlebar stem.
Handlebar stems connect the cycle handlebars to the front fork.
A rigid or adjustable handlebar stem may be fitted, depending on the cycle model.
There is a distinction between handlebar stems with internal clamping mechanisms and
handlebar stems which cover the fork stem and are clamped with bolts from outside.
Handlebar stem parameters include the diameter of the fork stem, diameter of the
handlebar clamp, length, angle and height.
Handlebar height is among the adjustments that must be made in adapting the cycle to
suit the size of the rider.
x Have the handlebars adjusted by your dealer so that you can sit in a comfortable
position and easily operate all the components on the handlebars.
4.3.1 Minimum insertion depth
Quill-type handlebar stems have a minimum insertion depth marked on their tubing, and
must be inserted up to at least this point in the fork stem.
x Observe the minimum insertion depth
for the handlebar stem. The marking on
the handlebar stem or quill must not be
visible (see “Illustr.: Minimum insertion
depth marking on a quill-type stem with
an internal clamping mechanism”).
Illustr.: Minimum insertion depth marking
on a quill-type stem with an internal
clamping mechanism (example)
Cycle Basic adjustments
39
x Note that height adjustments to A-head handlebar stems, which cover the fork
stem and are clamped with bolts from outside, require expertise. With this type
of handlebar stem, the handlebar height is adjusted using spacing washers and
limited by the fork stem length.
x Have your dealer carry out the adjustment.
4.3.2 Adjusting the handlebar stem tilt
Depending on the cycle model, the cycle may be equipped with a handlebar stem that
includes a tilt angle adjustment mechanism. The handlebar tilt must be adjusted so that
your wrists and forearms are in line when riding.
x Carefully loosen the side screw until the
splines release.
x Press the screw head with your thumb
to loosen the handlebar stem.
x Adjust the tilt of the movable handlebar
stem to your liking.
x Press the loosened adjustment
mechanism back into the handlebar
stem until the pawl is correctly engaged
with the splines.
x Tighten the screw by turning it
clockwise, using the recommended
torque.
4.3.3 Aligning the handlebars
The handlebars must be at a 90° angle to the
front wheel.
x Have the handlebars adjusted by your
dealer if they are not perpendicular to
the front wheel (see “Illustr.: Correct
handlebar alignment”).
Illustr.: Side screw on the handlebar stem
(example)
Illustr.: Tilt adjustment (example)
Illustr.: Correct handlebar alignment
CycleBasic adjustments
40
4.4 Controls
Controls (e.g. the bell, brake levers, gear shifting system, etc.) must be arranged so that
they can be operated easily while riding, without distracting you from the road, and if
possible without taking your hands off the handlebar grips.
x Have the controls adjusted by your dealer if you lack the necessary expertise or the
tools required.
4.5 Brake lever
WARNING
Loss of brake power due to incorrectly adjusted brakes.
Risk of accident and injury!
x Have brake adjustments carried out by your dealer only.
x Do not make any adjustments to the brakes if you lack the
necessary expertise or the tools required.
x Adjustments to the brake system are highly complex and require expertise. Have
your dealer carry out the adjustment.
4.5.1 Adjusting the position
The position of the brake levers must be
custom-adjusted so that the levers can be
operated easily and safely.
x Loosen the brake lever fastening by
turning the brake lever screw
anticlockwise (see “Illustr.: Brake lever
position”).
x Position the brake lever at a point
where your fingers, wrist and arm are in
line and your fingers are resting com-
fortably on the brake lever, and where
you can pull the lever safely.
x Tighten the brake lever screw by turning it clockwise. Ensure that the torque is
correct.
Illustr.: Brake lever position (example)
Cycle Basic adjustments
41
4.5.2 Adjusting the grip width
The grip width of the brake levers must be
custom-adjusted so that the levers can be
operated easily and safely. Mechanical and
hydraulic brakes generally have an
adjustment screw on the brake lever
(see “Illustr.: Adjustment screw position”).
Turning the adjustment screw alters the
distance between the brake lever and the
handlebar grip. The position of the
adjustment screw may vary depending on
the brake design.
1. If applicable, remove the protective cap
from the adjustment screw.
2. Adjust the brake lever to the grip width
of your hand by loosening or tightening
the adjustment screw.
3. Check the minimum distance by
operating the brake lever.
x If the distance between the
operated brake lever and the
handlebar grip is less than
1 cm/0.4", adjust the cable tension
or pressure point (see the “Brake /
Adjustments / Adjusting the brake
cable tension in mechanical brakes”
chapter or “Brake / Adjustments
/ Adjusting the pressure point”
chapter).
4. If applicable, place the protective cap over the adjustment screw.
4.6 Pedals
The pedals are fastened to the cranks and operated by foot to power the cycle.
The cycle may be equipped with folding pedals, block pedals or clipless pedals,
depending on the cycle model.
x When fitting pedals, note that the right pedal has a right-hand thread and the left
pedal has a left-hand thread. In both cases, the pedal is tightened in the crank by
screwing it in the direction of travel. Both pedals are loosened by unscrewing them
counter to the direction of travel.
1
1
Illustr.: Adjustment screw position (example)
1 Grip width adjustment screw
1
A
B
C
CycleBasic adjustments
42
4.6.1 Folding pedal
CAUTION
Folding pedals in and out incorrectly.
Risk of injury!
x Ensure that you do not get your fingers caught in the folding
mechanism.
x Wear protective gloves if necessary.
A folding pedal is a pedal with a folding mechanism. When storing or transporting the
cycle, the pedals can be folded in so that they sit close up against the cycle.
x Familiarise yourself with the folding system before using it for the first time.
x Refer to and follow the information enclosed by the manufacturer about using
folding pedals.
x Have your dealer explain the folding mechanism to you if necessary.
Illustr.: Folding pedal folded out (example)
Illustr.: Folding pedal folded in (example)
4.6.2 Block pedal
A block pedal is the traditional pedal variant
(see “Illustr.: Block pedal”).
Illustr.: Block pedal (example)
Cycle Basic adjustments
43
4.6.3 Clipless pedal
WARNING
Falling due to not disengaging shoes from the clipless system in
time.
Risk of accident and injury!
x Disengage your shoes from the pedals’ clipless system in
good time before stopping.
x Keep off the road while you practice engaging and
disengaging your shoes from the clipless system.
A clipless pedal has a device that allows
specially designed shoes to be locked in
place (see “Illustr.: Clipless pedal”). Engaging
your shoes in the clipless system keeps your
feet firmly connected with the pedals,
providing better grip and stability.
x Familiarise yourself with the clipless
system before using it for the first time.
x Adjust the release force and the cleats
before the first use.
x If you lack the necessary expertise to
adjust the pedals, contact your dealer.
Illustr.: Clipless pedal (example)
CycleBasic adjustments
44
4.6.4 Foot clearance
WARNING
Risk of falling due to insufficient foot clearance.
Risk of accident and injury!
x Ensure there is adequate foot clearance, depending on the
foot anchoring system.
x Have the foot anchoring system fitted by a dealer.
With racing bikes, the distance between the
pedal and the front wheel must not fall below
a certain foot clearance value. The distance is
measured parallel to the longitudinal axis of
the cycle, from the midpoint of the pedals to
the arc of the front wheel at full steering lock
(see “Illustr.: Distance between the pedal and
front wheel”).
Foot clearance on racing bikes
without a foot anchoring
system*
100 mm/3.9"
with a foot anchoring system*
89 mm/3.5"
* Foot anchoring systems: e.g. clipless
pedals or toe clips
1
23
4
Illustr.: Distance between the pedal and front
wheel (example)
1 Front wheel
2 Arc of the front wheel at full steering lock
3 Foot clearance = distance between the
pedal and front wheel
4 Pedal midpoint
Cycle Basic adjustments
45
4.7 Lighting
DANGER
Poor visibility to other road users.
Risk of accident and injury!
x Switch on lighting in poor visual conditions and in the dark.
WARNING
Inattention on the road due to switching on lighting.
Risk of accident and injury!
x Do not switch on lighting while riding. Always stop to switch
on the lighting.
In order to ride on the road, lighting and reflectors must meet national and regional
regulations.
x Refer to and follow national and regional regulations on lighting equipment.
x Acquaint yourself with these before your first ride. Retrofit your cycle to meet
the regulations if necessary. Contact your dealer about this.
Lighting consists of a headlamp, rear lamp and reflectors, and ensures better visibility in
poor visual conditions and at night.
The cycle may be equipped with hub dynamo fixed lighting or battery-powered clip-on
lighting, depending on the cycle model.
4.7.1 Hub dynamo
The hub dynamo, to which the headlamp is connected, is located in the front wheel
hub. The rear lamp is linked to the headlamp. The hub dynamo supplies the lighting with
power as soon as the front wheel is turned.
With a hub dynamo, the lighting is generally switched on directly from the headlamp or
from the handlebars. When the switch is operated, the rear lamp is switched on along
with the headlamp.
x Switch the lighting on and off by operating the switch.
Depending on the lighting model, there may be an integrated light sensor. In automatic
mode, the headlamp and rear lamp are switched on and off automatically depending on
the light conditions.
CycleBasic adjustments
46
x Adjust to automatic mode to switch on the light sensor.
Depending on the lighting model, the rear lamp on your cycle may have a standing light
feature which allows the rear lamp to remain lit for several minutes even when you stop
riding. This feature does not need to be switched on separately.
There are various types of headlamp with different switch options.
Have your dealer explain how they are operated and how they function.
4.7.2 Battery-powered and rechargeable lighting
Depending on the lighting model, the headlamp and rear lamp may be equipped with
different switches and need to be operated independently of each other.
x Switch the lighting on and off by operating the relevant switch.
x Refer to the information enclosed by the manufacturer about operating and fitting
battery-powered and rechargeable lighting.
4.7.3 Headlamp
1. Switch on the headlamp.
2. Adjust the headlamp so that, at a
distance of 5 m in front of the head-
lamp, the light beam reaches a point
only half as high as at its starting point
(see “Illustr.: Adjusting the headlamp”).
x An incorrectly adjusted headlamp
can dazzle other road users.
4.7.4 Rear lamp
A rear lamp must be installed in an easily visible location at the back of the cycle.
x Check that the rear lamp is functional before riding off.
4.7.5 Reflectors
Reflectors must be installed in an easily visible location on the cycle and must not be
obscured. Generally, reflectors are located on the pedals, the tyres, the rear lamp and
the headlamp.
x Check that all reflectors are undamaged and visible before riding off.
Illustr.: Adjusting the headlamp (example)
100 %
50 %
5 m
Cycle Basic adjustments
47
4.8 Suspension
This chapter contains information for the following cycle categories:
WARNING
Loss of traction due to incorrectly adjusted suspension.
Risk of accident and injury!
x Have the suspension adjusted by your dealer.
x Have your dealer explain how your suspension is operated
and adjusted.
NOTE
Impact noises due to incorrectly adjusted suspension.
Risk of damage!
x If you feel hard impacts or hear unusual noises upon
compression, have the suspension checked by your dealer.
Suspension reduces the forces acting on the rider when the road is uneven.
On bumpy ground, cycles with tuned suspension are more efficient and more
comfortable to ride.
x Refer to and follow the information enclosed by the manufacturer about features
and adjustments for your suspension.
CycleBrake
48
5 Brake
5.1 Basics
The cycle is equipped with at least two independent brakes. Depending on the cycle
model, the following brakes may be installed:
Coaster brake
Rim brake
Disc brake
5.1.1 Coaster brake
Cycles with hub shifting systems and cycles
without gear shifting systems are frequently
equipped with a coaster brake. This is
integrated in the cycle’s rear wheel hub and
operated using the pedals (see “Illustr.:
Coaster brake”).
5.1.2 Brake lever
The brakes are operated using the brake levers. Force is transmitted mechanically
or hydraulically. In the case of a mechanical design, the force from the brake lever is
transmitted to the brake via a cable. In the case of a hydraulic design, the force from the
brake lever is transmitted to the brake via brake lines which contain brake fluid.
If the cycle is equipped with just one brake lever, this operates the front brake. The rear
brake is the coaster brake.
If the cycle is equipped with two brake levers,
the left-hand brake lever is generally for the
front brake while the right-hand brake lever is
for the rear brake (see “Illustr.: Brake lever
arrangement”).
x Note that the arrangement of the
brake levers may vary. Familiarise
yourself with the brake lever
arrangement before setting off.
Contact your dealer if you would like
to have the brake lever arrangement
changed.
Illustr.: Coaster brake (example)
21
Illustr.: Brake lever arrangement (example)
1 Front brake lever
2 Rear brake lever
Cycle Brake
49
5.1.2.1 Disc brake
The brake discs are fastened to the wheel
hubs, with the corresponding brake calliper
fastened to the frame or front fork (see
“Illustr.: Disc brake”). The brake pads are
located inside the brake calliper. When the
brake lever is operated, the brake pads are
pressed against the brake disc and brake the
wheel.
5.1.2.2 Rim brake
Rim brakes are fastened to the front fork or rear frame. When operated, the brake block
holders are pressed against the braking surface of the rim sidewall to brake the wheel
(see “Illustr.: Mechanical rim brakes” and “Illustr.: Hydraulic rim brake”).
Depending on the brake design, mechanical rim brakes may be equipped with a
brake
force modulator. The brake force modulator partially regulates the brake lever force at
the front and prevents the front wheel locking up. The brake force modulator is installed
between the brake lever and rim brake.
Illustr.: Mechanical rim brakes (example)
1 Cable
2 Tyre
3 Rim
4 Brake block holders
1
3
2
4
2
3
1
4
1
3
2
4
1
2
Illustr.: Disc brake (example)
1 Brake calliper
2 Brake disc
CycleBrake
50
Illustr.: Hydraulic rim brake (example)
1 Brake line
2 Tyre
3 Rim
4 Brake block holders
2
3
1
4
Cycle Brake
51
5.2 Adjustments
The grip width must be custom-adjusted so that the brake lever can be
operated easily and safely (see the “Basic adjustments / Brake lever /
Adjusting the grip width” chapter).
5.2.1 Adjusting the brake cable tension in mechanical brakes
WARNING
Loss of brake action due to worn brake pads and cables.
Risk of accident and injury!
x Replace worn brake pads and cables.
x If you lack the necessary expertise and the tools required to
replace these, contact your dealer.
With mechanical brakes, minor brake pad wear is offset via the brake cable tension.
Changing the brake cable tension alters the distance between the rim and the brake
block holders. The position of the lock nut and knurled screw may vary depending on
the cycle model.
1. Loosen the lock nut by giving it one turn
anticlockwise.
2. To increase the cable tension, gradually
turn the knurled screw anticlockwise
until the distance between the
brake block holders and the rim is
1–2mm/0.04–0.08" on each side.
x Ensure that the brake block holders
meet the rim simultaneously on
both sides.
x Ensure that the wheel turns
smoothly (see the “Wheels and tyres
/ Rims and spokes” chapter).
3. Tighten the lock nut by turning it clockwise.
x If the brake cannot be adjusted through the cable tension, have the brake
adjusted by your dealer.
Illustr.: Lock nut and knurled screw position
(example)
1 Lock nut
2 Knurled screw
1 2
CycleBrake
52
5.2.2 Adjusting the pressure point
With hydraulic brakes, minor break pad wear
is offset via the pressure point adjustment
screw (see “Illustr.: Adjustment screw
position”). The adjustment screw is generally
located on the brake lever. Brakes without an
adjustment screw have the distance adjusted
automatically.
The distance between the rim and brake pad
is increased or decreased depending on the
turning direction.
x For rim brakes, gradually turn the adjustment screw until the distance between the
rim and each brake pad is 1–2mm/0.04–0.08" .
x Ensure that the brake block holders meet the rim simultaneously on both sides.
x Ensure that the wheel turns smoothly (see the “Wheels and tyres / Rims and
spokes” chapter).
x For disc brakes, gradually turn the adjustment screw until the desired pressure
point is reached.
Illustr.: Adjustment screw position (example)
1 Pressure point adjustment screw
1
Cycle Brake
53
5.3 Operation
WARNING
Risk of overturning due to pulling the front brake.
Risk of accident and injury!
x Use the front brake lever carefully at high speeds to prevent
overturning.
x Always brake using both brakes simultaneously for optimum
brake power.
x Adapt the braking force from the brakes to suit the riding
situation, road conditions and weather so that you avoid
locking up the wheels.
x Use the rear brake carefully when cornering to prevent the
rear wheel locking up.
WARNING
Longer braking distance due to reduced brake power in the wet.
Risk of accident and injury!
x Adapt your riding style and speed to suit the weather and
road conditions.
5.3.1 Operating the brake lever
x To operate a brake lever, pull it towards
the handlebar grip with your fingers.
2
1
Illustr.: Operating the brake lever (example)
1 Brake lever
2 Handlebar grip
CycleBrake
54
5.3.2 Operating the coaster brake
WARNING
No coaster brake action where the chain has dropped off the
chainring.
Risk of accident and injury!
x If the coaster brake has no effect, brake carefully using the
front brake lever and also the rear brake lever if applicable.
The coaster brake only functions when riding forwards. The coaster brake
is operated most effectively if the pedals are in a horizontal position with the
downward force acting on the rear pedal. Operate the brake levers when
rolling backwards.
The coaster brake is operated by back-
pedalling, and brakes the rear wheel
(see “Illustr.: Operating the coaster brake”).
x Ensure that the crankset is functional,
as the braking force is transmitted via
the chain.
x To operate the coaster brake, pedal
counter to the direction of travel.
5.4 Bedding in disc brakes
New brakes must be bedded in before they can reach their full brake power.
x Keep off the road while bedding in the brakes.
x Brake in a controlled manner to prevent the wheels locking up.
x Operate both brake levers simultaneously.
x Bedding in consists of around 30 short periods of braking. Brake from around
25 km/h/15.5 mph down to a stop. The bedding-in process is complete when a
consistent brake action is produced upon steadily operating the brake lever.
Illustr.: Operating the coaster brake (example)
Cycle Derailleur shifting system
55
5.5 Maintaining braking force
Diminished brake action in disc brakes due to the brake system overheating is known
as “fading”. When the temperature at the point of contact between the brake pads and
brake disc rises, e.g. due to continuous braking, the brake power drops.
x Avoid long periods of continuous braking.
x Allow the brake pads to cool down regularly.
x Do not use the cycle if the brake power is reduced due to warming.
x Only use the cycle again once full brake power is restored.
6 Derailleur shifting system
6.1 Basics
Usually all modern cycles have a gear shifting system installed; this depends on the
cycle model. Exceptions include children’s bikes, which may only have one gear
depending on the model.
The gear shifting system on a cycle consists of a variable gear unit and the
corresponding controls. As a result, the power provided by the rider is adapted to suit
the riding speed and route conditions.
A derailleur shifting system consists of 1 to 3 chainrings on the crankset and
6to12sprockets on the rear wheel (see “Illustr.: Components of a derailleur shifting
system”). Separate controls on the right and in some cases the left-hand side of the
handlebars are generally used to shift sprockets and chainrings
(see the “Derailleur shifting system / Operation” chapter).
Adjustments to the gear shifting system require expertise.
x If you lack the necessary expertise and the tools required, contact your dealer.
CycleDerailleur shifting system
56
6.1.1 Mechanical derailleur shifting system
x When shifting gear, pedal only gently.
The theoretical number of gears is
determined with a “chainrings × sprockets”
calculation (see the “Derailleur shifting system
/ Basics / Gear combinations” chapter).
The smaller the sprocket, the higher the
selected gear and the lower the cadence.
The larger the sprocket, the lower the
selected gear and the higher the cadence.
The smaller the chainring, the higher the
cadence.
x Use a low gear on inclines.
x Use a high gear for higher speeds on flat
routes.
6.1.2 Electronic derailleur shifting system
An electronic derailleur shifting system is powered by a rechargeable battery which
provides electricity for the front and rear derailleurs. It functions the same way as a
mechanical derailleur shifting system. The shifter buttons can be pressed in quick
succession. The shifting system registers how many times they have been pressed, then
moves the chain quickly and precisely. The shifting system automatically prevents an
excessively crossed chain line.
The cycle, generally a racing bike or MTB, may have an electronic shifting
system depending on the model.
Gears are shifted up or down by pressing the relevant shift lever. The electronics ensure
that the gears are changed quickly.
x Contact your dealer for further information and if you have any questions, or refer
to the manual enclosed with the electronic derailleur shifting system.
Illustr.: Components of a derailleur shifting
system (example)
1 Shift cable
2 Cassette of several sprockets on the rear
wheel
3 Chainrings on the crankset
4 Chain
3
2
4
1
Cycle Derailleur shifting system
57
6.1.3 Gear combinations
NOTE
Incorrect use of gear combinations.
Risk of damage!
x Never combine the small chainring with the smallest
sprockets
or the large chainring with the largest sprockets.
With incorrect gear combinations, a crossed
chain results in increased wear on the
chainrings, sprockets and chain.
Proper use only allows for certain
gear combinations (see “Illustr.: Gear
combinations”).
x Use the gear combinations in such a
way that the chain runs parallel to the
direction of travel.
x Use the smallest chainring on inclines
and the largest chainring for higher
speeds on flat routes.
x If you are unsure about operating the gear shifting system, have your dealer give
you instructions.
Illustr.: Gear combinations (example)
1 7 sprockets on the rear wheel
2 3 chainrings on the crankset
21
CycleDerailleur shifting system
58
6.2 Adjustments
WARNING
Dropped or jammed chain due to an incorrectly adjusted gear
shifting system.
Risk of accident and injury!
x Adjust the gear shifting system.
x If you lack the necessary expertise or the tools required,
contact your dealer.
CAUTION
Pinching and crushing of body parts by moving components.
Risk of injury!
x Be careful when handling moving parts so as not to get your
fingers caught.
x Wear protective gloves if necessary.
NOTE
An incorrectly adjusted gear shifting system can cause damage
to the system itself.
Risk of damage!
x Adjust the gear shifting system.
x If you lack the necessary expertise or the tools required,
contact your dealer.
Cycle Derailleur shifting system
59
To shift gears smoothly, it is important that
the front and rear derailleurs are precisely
adjusted (see “Illustr.: Components of a
derailleur shifting system”).
x If the derailleur shifting system does
not function or makes a noise when
operated, have the system adjusted by
your dealer.
6.2.1 Adjusting the rear derailleur
To keep the chain and rear derailleur out of
the spokes and prevent the chain falling off
the smallest sprocket, the stop screws
(L and H) limit the range through which the
rear derailleur can pivot (see “Illustr.: Diagram
of a rear derailleur”).
L stands for “low gear”.
H stands for “high gear”.
To adjust the rear derailleur, follow these
steps:
1. Shift the chain onto the largest chainring
and the smallest sprocket at the rear
derailleur.
2. Turn the H stop screw until the guide
pulley is exactly underneath the smallest
sprocket.
3. Pull the shift cable taut and fix it in place using the cable tensioning screw on the
chain stays (see “Illustr.: Adjusting the rear derailleur”).
4. Shift the chain onto the smallest chainring and the largest sprocket.
Illustr.: Components of a derailleur shifting
system (example)
1 Shift cable
2 Front derailleur
3 Rear derailleur
L
1
3
2
Illustr.: Diagram of a rear derailleur (example)
1 Largest sprocket
2 Smallest sprocket
3 H stop screw
4 L stop screw
5 Guide pulley
3
4
5
2
1
CycleDerailleur shifting system
60
5. Ensure that the chain does not touch
the spokes under any circumstances.
If necessary, correct this using the L stop
screw (see “Illustr.: Front derailleur”).
6.2.2 Adjusting the front derailleur
x Shift the chain onto the smallest
chainring.
x Adjust the distance from the inner cage
using the L stop screw. The distance
should be 0.5–1 mm/0.02–0.4"
(see “Illustr.: Front derailleur”).
x Shift the chain onto the largest chainring.
x Adjust the distance from the outer cage
using the H stop screw. The distance
should be 0.5–1 mm/0.02–0.4".
6.2.3 Readjusting the shift cable tension
x If noises are produced after shifting gear while riding, correct the shift cable tension
using the cable tensioning screw on the shift lever (see “Illustr.: Cable tensioning
screw on the shift lever”).
x To do this, give the
cable tensioning screw a half turn.
x If the noises decrease, turn the
cable tensioning screw little by little
in the same direction until no more
noises are produced when riding.
x If the noises increase, turn the cable
tensioning screw little by little in the
opposite direction until no more
noises are produced when riding.
x If noises continue to be produced after
shifting gear while riding, have the gear shifting system adjusted by your dealer.
Illustr.: Adjusting the rear derailleur (example)
1 Cable tensioning screw on the chain stays
1
1
Illustr.: Front derailleur (example)
1 H stop screw
2 L stop screw
2
Illustr.: Cable tensioning screw on the shift
lever (example)
Cycle Derailleur shifting system
61
6.2.4 Adjusting the derailleur shifting system on a racing bike
If the racing bike has shift cables where the
adjustment screw is equipped with an
adjusting wheel, then the cable tension in the
derailleur shifting system can be readjusted
there.
x To increase the cable tension, turn
the wheel of the adjustment screw
anticlockwise.
x To reduce the cable tension, turn
the wheel of the adjustment screw
clockwise.
To adjust the rear derailleur, see
the “Derailleur shifting system/
Adjustments/ Adjusting the rear
derailleur” chapter.
Illustr.: Adjusting the derailleur shifting system
(example) Adjustment screw with
cable tension adjusting wheel
CycleDerailleur shifting system
62
6.3 Operation
WARNING
Inattention on the road.
Risk of accident and injury!
x Familiarise yourself with the features of the gear shifting
system before your first ride.
x Only operate the gear shifting system if it will not take any of
your attention off the road.
x Stop if you cannot operate the gear shifting system safely,
e.g. in the event of a malfunction.
NOTE
Increased wear and damage due to operating the gear shifting
system incorrectly.
Risk of damage!
x Do not pedal hard when shifting gears.
x Do not back-pedal when shifting gears.
x Shift down in good time before inclines.
x If you are not familiar with gear shifting systems, have your dealer explain how the
shifting system is operated.
6.3.1 Shifting sprockets
The arrangement of the shift levers (top or bottom of the handlebars) and their operation may
vary depending on the model. The shifting unit for the cassette is located on the right-hand
side of the handlebars (see “Illustr.: Handlebar control for shifting sprockets and chainrings”).
Cycle Derailleur shifting system
63
x To shift onto the next largest sprocket, press the lower shift lever.
x Some models offer the possibility of shifting down multiple gears at once.
To do this, press the shift lever further.
x To shift onto the next smallest sprocket, press the upper shift lever.
x Some models offer the possibility of shifting up a gear by pulling the shift lever
in the opposite direction with your index finger.
x Once operated, release the shift lever so that it can automatically return to its
starting position.
If your cycle model is equipped with a twist-
grip control:
x Twist-grip controls are generally marked
with numbers for the individual gears.
Turn the twist-grip control in the relevant
direction to shift up or down.
6.3.2 Shifting chainrings
The arrangement of the shift levers (top or bottom of the handlebars) and their operation may
vary depending on the model. The chainring shifting unit is located on the left-hand side of
the handlebars (see “Illustr.: Handlebar control for shifting sprockets and chainrings”).
x To shift onto the next largest chainring, press the lower shift lever.
x To shift onto the next smallest chainring, pull the upper shift lever on the left-hand
side of the handlebars
.
x Once pressed, release the shift lever so that it can automatically return to its starting
position.
1
2
Illustr.: Handlebar control for shifting sprockets and chainrings (on the right-hand side of the
handlebars here as an example)
1 Upper shift lever
2 Lower shift lever
1
2
Illustr.: Twist-grip control (example)
CycleDerailleur shifting system
64
If your cycle model is equipped with a twist-grip control:
x Twist-grip controls are generally marked with numbers for the individual gears.
Turn the twist-grip control in the relevant direction to shift up or down
(see “Illustr.: Twist-grip control”).
6.3.3 Electronic derailleur shifting system
An electronic derailleur shifting system requires dedicated button controls on the
handlebars. The shifter buttons can be pressed in quick succession. The shifting system
registers how many times they have been pressed, then moves the chain quickly and
precisely. The shifting system automatically prevents an excessively crossed chain line.
6.3.4 Derailleur/hub shifting system (Dual Drive)
x If your cycle is equipped with a combined derailleur/hub shifting system, read the
“Hub shifting systems / Operation / Derailleur/hub shifting system (Dual Drive)”
chapter as well.
6.3.5 Operating the shift levers on a racing bike
Racing bikes with curved handlebars generally have racing shift/brake levers installed,
where the shifters are integrated into the brake lever. Depending on the model of the
gear shifting system, gears may be shifted by moving the brake lever or by operating
shift levers. On straight handlebars, the shift levers are located underneath the
handlebars as with other types of cycle; see the “Derailleur shifting system” chapter.
Ask your dealer how the shift levers are operated. Keep off the road while
you practice shifting gears to familiarise yourself with how the shift levers
function.
Cycle Hub shifting systems
65
7 Hub shifting systems
7.1 Basics
Usually all modern cycles have a gear shifting
system installed; this depends on the cycle
model. Exceptions include children’s bikes,
which may only have one gear depending on
the model.
The gear shifting system on a cycle consists
of a variable gear unit and the corresponding
controls. As a result, the power provided by
the rider is adapted to suit the riding speed
and route conditions.
Adjustments to the gear shifting system
require expertise.
x If you lack the necessary expertise and
the tools required to adjust the hub
shifting system, contact your dealer.
7.1.1 Automatic shifting system (Automatix)
This chapter applies to models with an optional “Automatix” gear shifting
system (see the specifications data sheet provided by the dealer).
The rear wheel hub is equipped with an automatic shifting system. The gear shifting
system automatically shifts up to 2nd gear or down to 1st gear depending on your speed.
Automatix gear shifting systems are available both with a freewheel and with a coaster
brake. Check the data sheet completed by your dealer to find out which variant is
installed.
x If the gear shifting system does not shift gear automatically, or produces noises,
have the system checked by your dealer.
Illustr.: Components of a hub shifting system
(example)
1 Fastening ring
2 Ratchet
3 Holder
3
1
2
CycleHub shifting systems
66
7.1.2 Stepless gear shifting system (NuVinci)
This chapter applies to models with an optional “NuVinci” stepless gear
shifting system (see the specifications data sheet provided by the dealer).
The rear wheel hub is equipped with a stepless gear shifting system.
The gear
shifting system is infinitely adjustable by turning the twist-grip control
.
NuVinci gear shifting systems are available both with a freewheel and with a coaster
brake. Check the data sheet completed by your dealer to find out which variant is
installed.
7.1.3 Stepless automatic gear shifting system (NuVinci Harmony)
This chapter applies to models with an optional “NuVinci Harmony”
stepless automatic gear shifting system (see the specifications data sheet
provided by the dealer).
The rear wheel hub is equipped with a stepless automatic gear shifting system
which is not operated manually, but instead adapts to your speed and cadence
automatically.
7.1.4 Electronic hub shifting system
An electronic hub shifting system requires dedicated button controls on the handlebars.
The shifter buttons can be pressed in quick succession. The shifting system registers
how many times they have been pressed, then changes gear accordingly.
7.2 Adjustments
WARNING
Gear slippage and ineffective pedalling due to an incorrectly
adjusted gear shifting system.
Risk of accident and injury!
x Adjust the gear shifting system.
x If you lack the necessary expertise or the tools required,
contact your dealer.
Kick-shift system (S2 Duomatic)
This chapter applies to models with an optional
“S2 Duomatic” gear shifting system (see the specifica-
tions data sheet provided by the dealer).
The rear wheel hub is equipped with a gear shifting system.
The
gear shifting system is shifted up to 2nd gear or down to 1st gear
by briefly
back-pedalling the crankset.
S2 Duomatic gear shifting systems are available both with a free-
wheel and with a coaster brake. Check your cycle passport to see
which variant is installed.
NOT WANTED BY MR DREHMEL!
Cycle Hub shifting systems
67
NOTE
An incorrectly adjusted gear shifting system can cause damage
to the system itself.
Risk of damage!
x Adjust the gear shifting system.
x If you lack the necessary expertise or the tools required,
contact your dealer.
Adjustments to hub shifting systems may only be carried out by your dealer.
7.2.1 Adjusting the shift cable tension
Shift cable tension adjustment is dependent on the model of your hub shifting system.
x Check what hub shifting system is installed on your cycle (see the specifications
data sheet provided by the dealer).
x If the functionality of the hub shifting system declines, adjust the shift cable tension.
1. Adjust the twist-grip control or shift lever
to the middle gear setting. In a 7 or
8-speed system, this corresponds to
4th gear (see “Illustr.: Adjustment screw
on the twist-grip control”).
2. Adjust the twist-grip control adjustment
screw (see “Illustr.: Adjustment screw on
the twist-grip control”) so that the two
coloured markings on the rear wheel
hub match up (see “Illustr.: Adjustment
marking”).
3. Check the adjustments with a test ride.
x If you were unable to rectify the
malfunction, have the shift cable
tension adjusted by your dealer.
Illustr.: Adjustment screw on the twist-grip
control (example)
1 Gear level
2 Adjustment screw
1
2
L
OC
K
Illustr.: Adjustment marking (example)
CycleHub shifting systems
68
A hub shifting system with a shift box may be installed, depending on the cycle model.
x Check the rear axle of the cycle to see whether a shift box is installed.
1. Adjust the twist-grip control or shift lever
to the middle gear setting. In a 7 or
8-speed system, this corresponds to
4th gear (see “Illustr.: Shift box”).
2. Adjust the adjustment nut so that the
markings on the shift box match up (see
“Illustr.: Shift box”).
3. Check the adjustments with a test ride.
x If you were unable to rectify the mal-
function, have the shift cable tension
adjusted by your dealer.
7.2.2 Adjusting the shift cable tension in a NuVinci shifting system
x If there is less than 0.5 mm/0.02" of
play between the shift cable casing and
the barrel, turn the adjustment nut
clockwise (see “Illustr.: Play between the
shift cable casing (left) and adjustment
screw (right)”)
x If there is more than 1.5 mm/0.06"
of play, turn the adjustment nut
anticlockwise.
x Refer to the information enclosed
with the cycle by the shifting system
manufacturer.
x If you were unable to rectify the
malfunction, have the gear shifting
system adjusted by your dealer.
1 2
Illustr.: Shift box (example)
1 Marking
2 Adjustment nut
Illustr.: Play between the shift cable casing
(left) and adjustment screw (right)
(example)
1 0.5
1.5 mm/0.02–0.06"
2 Shift cable casing
3 Barrel
4 Adjustment screw
2 3 41
Cycle Hub shifting systems
69
7.3 Operation
WARNING
Inattention on the road.
Risk of accident and injury!
x Familiarise yourself with the features of the gear shifting
system before your first ride.
x Only operate the gear shifting system if it will not take any of
your attention off the road.
x Stop if you cannot operate the gear shifting system safely,
e.g. in the event of a malfunction.
NOTE
Increased wear and damage due to operating the gear shifting
system incorrectly.
Risk of damage!
x Do not pedal hard when shifting gears.
x Do not back-pedal when shifting gears.
x Shift down in good time before inclines.
Depending on your cycle model, a twist-grip control or shift lever with gear display may
be installed. Twist-grip controls with a gear display are generally installed, and these are
described here as an example.
Hub shifting systems are either stepless or have a number of gear levels.
x If you have no experience with gear shifting systems, have your dealer explain how
the shifting system is operated.
CycleHub shifting systems
70
7.3.1 Hub shifting systems with gear levels
x To shift up or down, turn the twist-grip
control to the desired position (see
“Illustr.: Twist-grip control”).
7.3.2 Stepless hub shifting systems
x Turn the twist-grip control to shift up or
down to an infinitely variable level (see
“Illustr.:Stepless twist-grip control”).
7.3.3 Derailleur/hub shifting system (Dual Drive)
x Position the shift lever to the left on
uphill routes (see “Illustr.: Dual Drive
combined twist-grip and shift lever
control”).
x Position the shift lever in the middle on
flat routes.
x Position the shift lever to the right on
downhill routes.
x Turn the twist-grip control to shift up or
down.
Illustr.: Twist-grip control (example)
Illustr.: Stepless twist-grip control (example)
1 Display
2 Flat
3 Incline
2 31
Illustr.: DualDrive combined twist-grip and
shift lever control (example)
Cycle Pinion gearbox
71
8 Pinion gearbox
A Pinion gearbox is a bottom bracket shifting
system, and can be used with a chain or a
belt drive (not illustrated). The Pinion gearbox
has a twist-grip control fastened to the
handlebars for shifting gears. With a Pinion
gearbox, the chain is tensioned by means of
a chain adjuster (see “Illustr.: Pinion gearbox
with a chain drive”) or sliding fork ends (not
illustrated). For belt tensioning, see the “Belt
drive / Checking the belt tension” chapter.
The Pinion gearbox is an oil-bath gearbox
(see the “Pinion gearbox / Oil change”
chapter). It is not possible to use a coaster
brake with a Pinion gearbox.
8.1 Before every ride
WARNING
Component failure.
Risk of accident and injury!
x Observe the maximum rider weight limit of 110 kg/243 lbs
(including luggage and/or backpack).
x Only use your Pinion gearbox cycle in ambient temperatures
between –15 °Cand 40 °C/5 °F and 104 °F.
1 2
3 4
Illustr.: Pinion gearbox with a chain drive
(example)
1 Sprocket
2 Chain
3 Chainring
4 Pinion gearbox
5 Chain adjuster
5
CyclePinion gearbox
72
WARNING
Chain or belt motion while the crank is stationary.
Risk of accident and injury!
x Before every ride, make sure that the sprockets and rear
wheel hub can freewheel smoothly.
x Turn the crank backwards. The chain must not revolve when
the sprockets and rear wheel hub are freewheeling.
x Stop if damage occurs to the Pinion gearbox or unusual
noises are produced.
8.2 Shifting gears with a Pinion gearbox
Note that the shifting behaviour of a Pinion gearbox, both with a chain and
with a belt drive, is different to that of a derailleur shifting system. Keep off
the road while you familiarise yourself with the Pinion gearbox and the
change in shifting behaviour.
The marking (“>>”) on the fixed part of the twist-grip control shows the selected gear,
for example between 01 and 18.
x To shift into a higher or lower gear, first move the twist-grip control slightly in the
direction you want to shift, then quickly shift in the desired direction.
It is possible to shift through multiple gears at once, such as from 02 to 06.
Gears can be shifted while at a standstill and while the crank is stationary or turning
backwards.
There is limited potential for shifting down under load, for example from 18 to 17.
To protect the Pinion gearbox, gears are not shifted when the pressure on the
crank or pedal is too strong, such as when riding out of the saddle.
x Only shift down when there is not a heavy load on the crank or pedal.
There is potential for shifting up under load, for example from 02 to 03.
Exceptions to this are gear changes from 06 to 07 and from 12 to 13, as the
gearbox needs to double-shift for these gear changes.
x Only shift from 06 to 07 or from 12 to 13 when there is not a heavy load on the
crank or pedal.
It is not possible to shift directly from the lowest gear to the highest or from the
highest gear to the lowest.
Cycle Pinion gearbox
73
x If the gears no longer shift precisely after running in or after longer use, contact
your dealer.
8.3 Troubleshooting
A Pinion gearbox generally runs quietly with no disturbing noises. If any
noises are produced and the gears shift properly, then the noises have
another cause.
Troubleshooting when using a Pinion gearbox
Fault Possible cause Solution
With a belt drive
Grinding noises Belt Alter the belt tension
Belt tension varies in the
course of a revolution
Front pulley is not centred,
chainring bolts do not hold the
front pulley central
Use chainring bolts with
an external diameter of
10mm/0.4"
With a belt drive and with a chain drive
Creaking noises Pedals, saddle, handlebars Check all components or have
them checked by the dealer
Cracking noises Drive components with loose
screw joints
Check the screw joints of
drive components and have
the dealer tighten them with a
torque wrench if necessary
Clicking in 7th and 13th gear Both gear levels have a
freewheel pawl (models
manufactured before 2014)
Noise is not a defect.
Chargeable upgrade to new
version of the gearbox on
request
Humming or buzzing Crossed chain or belt Straighten the chain or belt
Gears do not shift smoothly Worn or incorrect shift cables,
outer casings or end caps
Only use shift cables with
a maximum diameter of
1.2mm/0.05"; only use shift
cable outer casings; only use
plastic end caps; be sure to
replace worn shift cables
Slippage when pedalling Freewheel pawl does not
engage correctly
Further pedalling will engage
the gear with the next tooth
CyclePinion gearbox
74
Troubleshooting when using a Pinion gearbox
Fault Possible cause Solution
With a chain drive
Chain hits the chain stays Chain tension too low Have the chain tension
adjusted by the dealer
Despite a functioning rear
freewheel, pushing causes the
chain or crank to revolve
Chain tension too high
8.4 Cleaning a Pinion gearbox
NOTE
Damage to the Pinion gearbox due to using harsh or abrasive
cleaners.
Risk of damage!
x Only clean the Pinion gearbox with water, dishwashing liquid
and a soft, clean brush.
x Do not use strong jets of water or high-pressure equipment to
clean the Pinion gearbox.
8.5 Maintaining a Pinion gearbox
NOTE
Loss of leak-tightness in the Pinion gearbox.
Risk of damage!
x Do not under any circumstances tighten or loosen the screws
to the Pinion gearbox casing cover.
Cycle Pinion gearbox
75
8.5.1 Maintaining a Pinion gearbox with a chain drive
x Regularly clean the chain, chainring, sprockets, and if necessary the Pinion
gearbox chain adjuster (see the “Pinion gearbox / Cleaning a Pinion gearbox”
chapter).
x Care for the chain by regularly applying a suitable lubricant.
8.5.2 Maintaining a Pinion gearbox with a belt drive
x Regularly clean the belt as well as the front and rear pulleys (see the “Belt drive /
Cleaning the belt drive” chapter).
x Check the belt drive regularly for wear (see the “Belt drive / Belt drive wear” chapter).
For further maintenance work:
x If you lack the necessary expertise and the tools required, have maintenance work
carried out by your dealer.
8.6 Oil change
NOTE
Oil leakage or spillage.
Pollution!
x Ensure that no oil gets into the sewer system or groundwater.
x Dispose of used oil in an environmentally friendly manner,
according to applicable national and regional regulations.
The oil in the Pinion gearbox must be changed every 10,000 km/6,250 mi or once a
year, whichever comes first.
x If you lack the necessary expertise and the tools required, have the oil changed by
your dealer.
1. Set out a collection container.
2. Use a suitable tool to loosen the four screws on the left-hand side of the gearbox
cover (if looking in the direction of travel).
3. Use a suitable tool to loosen the oil drainage screw on the lower edge of the gearbox.
4. Lie the cycle on its left-hand side (if looking in the direction of travel) over the
collection container and drain the oil into the container.
5. Stand the cycle upright or lie it on its right-hand side (if looking in the direction of
travel).
CycleBelt drive
76
6. Pour in new original Pinion gear oil.
7. Tighten the oil drainage screw with a suitable torque wrench, observing the torque
for the oil drainage screw.
8. Tighten the four screws to the gearbox cover with a suitable torque wrench,
observing the torque for the gearbox cover screws.
9 Belt drive
In addition to the commonplace chain drive, there are also belt drives available for
cycles.
x If you lack the necessary expertise and the tools required to adjust or maintain a
belt drive, have the drive checked and adjusted by your dealer.
9.1 Belt drive structure
A belt drive consists of a front and a rear
pulley, plus a belt which may be made from
various plastics depending on the belt model.
To prevent the belt running off the pulleys,
each pulley has a side flange. On the front
pulley, the side flange is located on the
outside. On the rear pulley, the side flange is
located on the inside. Belt drives are
compatible with hub shifting systems and
coaster brakes, but not with derailleur
shifting systems.
9.2 Using the belt drive
NOTE
Damage to the belt due to incorrect handling.
Risk of damage!
x Ensure that the belt is not creased, twisted, bent backwards,
turned inside out, tied or used as a strap wrench.
x During fitting, the belt must not be rolled up with the front
pulley chainring or levered on e.g. with a screwdriver.
1 2
3 4
Illustr.: Belt drive (example)
1 Rear pulley
2 Rear side flange
3 Belt
4 Front pulley (side flange hidden)
Cycle Belt drive
77
With a belt drive, the force exerted by the rider is transmitted via a belt.
Cycles with belt drives can be used in all weather conditions which are suitable for bikes.
9.3 Checking the belt tension
In order for the belt drive to function properly,
the belt needs to be correctly tensioned.
Have the belt tension regularly checked by
your dealer.
9.4 Belt drive wear
To minimise wear with a belt drive, it is important for the belt to run parallel between the
side flanges. Depending on the model of the belt drive, there should be
a maximum deviation of 3 mm/0.1" measured at the centre of the belt’s running
surface
and/or a maximum angular misalignment of 0.5° between the pulleys.
x If you find wear on the belt drive but you lack the necessary expertise and the tools
required to replace it, have the belt drive or worn parts replaced by your dealer.
9.4.1 Visually inspecting the belt for wear
The belt is subject to a certain degree of wear, depending on distance travelled and
riding conditions.
x Visually inspect the belt regularly for signs of wear.
If for example you find pointed, torn or
missing teeth (see “Illustr.: Belt wear”),
then the belt is worn.
Illustr.: Belt tension (example)
Illustr.: Belt wear (example)
CycleBelt drive
78
9.4.2 Visually inspecting the belt drive for wear
Sign of wear Solution for belt drive
Replace front pulley Replace rear pulley Replace belt
Front pulley
Side flange bent inwards x x x
Side flange bent outwards x
Tooth profile damaged x
Rear pulley
Wobbling on hub x
Faulty fit x
Spinning x
Sheared pulley x x
Sharp side flange x x
Belt
Creased belt x
Belt tooth profile damaged x
Belt cracked, porous x
Belt frayed x
Tearing in belt x
9.4.3 Visually inspecting the chainring for wear
If for example you find chainring teeth
shaped like shark teeth
(see “Illustr.: Chainring wear”),
then the chainring is worn.
Illustr.: Chainring wear (example)
Cycle Wheels and tyres
79
9.5 Cleaning the belt drive
NOTE
Damage to the belt drive due to using harsh or abrasive cleaners.
Risk of damage!
x Only clean the belt drive with water and a soft brush.
10 Wheels and tyres
A wheel consists of a hub, spokes and a rim.
Tyres are fitted to the wheel rim. Depending
on the cycle model, the tyre may contain an
inner tube. The front tyre is part of the front
wheel and the rear tyre is part of the rear
wheel.
If an inner tube is used, rim tape is
placed on the rim to protect the inner
tube from the rim surface and the spoke
nipples.
If no inner tube is used, “tubular”
tyres are used for racing bikes or UST
(universal system tubeless) tyres for
MTBs.
Wheels are exposed to considerable loads due to the weight of the rider and luggage, as
well as bumps in the road.
x Have the wheels checked and re-centred by your dealer after breaking in the
cycle (no longer than 300 km/190 mi of riding, 15 hours of operation or 3 months,
whichever comes first).
x Check the wheels regularly after breaking in.
x If you lack the necessary expertise and the tools required, have your dealer check
the wheels and centre them if necessary.
10.5.1 Kick-shift system
10.5.1.1 S2 Duomatic
This chapter applies to models with an optional
“S2 Duomatic” gear shifting system (see “Cycle
passport”).
x To shift up or down, briefly and gently back-pedal the
crankset.
NOT WANTED BY MR DREHMEL
1
2
3
4
5
6
Illustr.: Cross section of a wheel and tyre
(example)
1 Rim
2 Rim tape
3 Sidewall braking surface
4 Inner tube
5 Tyre
6 Tread
CycleWheels and tyres
80
10.1 Tyres and valves
DANGER
Poor visibility to other road users.
Risk of accident and injury!
x Ensure that reflectors are clean and easily visible.
CAUTION
Inner tube blow-out due to penetration by foreign bodies.
Risk of accident and injury!
x Check the tyres regularly for damage and wear.
x Replace damaged or worn tyres immediately.
x Have damaged or worn tyres replaced by your dealer if you
lack the necessary expertise and the tools required.
NOTE
Damage due to fitting a tyre that differs from the original size.
Risk of damage!
x Contact your dealer if you have any questions about tyre size.
The tyres allow the cycle to grip the road, transmit the drive forces to the road surface,
and provide cushioning against bumps. Various types of tyre may be fitted depending on
how the cycle is used.
Tyre size is indicated on the sidewall of each tyre. A variety of specifications may be
recorded here, such as:
The ETRTO size, which is given in millimetres. If 52-559 is indicated on the tyre,
then the inflated tyre is 52 mm wide with an internal diameter of 559 mm.
(ETRTO stands for the European Tyre and Rim Technical Organisation).
The size in inches. If 26 × 2.35 is indicated on the tyre, then the inflated tyre is
2.35" wide with an internal diameter of 26".
Cycle Wheels and tyres
81
With the exception of tubular tyres and UST tyres, the tyre and rim alone are not airtight.
An inner tube is used to keep air inside the tyre, and this is filled via a valve.
10.1.1 Valve types
Cycles may be equipped with one of the following valve types (see “Illustr.: Valve types”):
Presta valve (PV): secured with a tappet
in the valve, rim hole 6.5 mm/0.26",
maximum pressure 217.5 psi.
Dunlop valve (DV): secured with a union
nut, rim hole 8.5 mm/0.33", maximum
pressure 87 psi.
Schrader valve (SV): secured with a
tappet in the valve, rim hole
8.5 mm/0.33", maximum pressure
145 psi.
All three valve types have a valve cap to
prevent the valve getting dirty.
1
2
4
3
PV DV SV
Illustr.: Valve types (example)
1 Knurled screw
2 Valve tappet
3 Lower knurled nut
4 Upper knurled nut
CycleWheels and tyres
82
10.1.2 Tyre pressure
WARNING
Inner tube blow-out or tyre jumping off the rim due to excessively
high tyre pressure.
Risk of accident and injury!
x Observe the tyre pressure.
x Use a pump with a pressure display when inflating the tyres.
NOTE
Damage to the inner tube due to insufficient tyre pressure.
Risk of damage!
x Do not ride over sharp edges if the tyre pressure is too low.
x Observe the tyre pressure.
x Use a pump with a pressure display when inflating the tyres.
Tyre pressure is indicated on the sidewall of the tyre. The tyre pressure is given in bar or
psi (pounds per square inch). See the “Tyre pressure conversion” table.
The lower tyre pressure limit is suitable for light riders and uneven ground, and provides
more comfortable suspension with greater rolling resistance. The upper tyre pressure
limit is suitable for heavy riders and even ground, and provides low rolling resistance with
less comfortable suspension.
x Always ride with the prescribed tyre pressure.
x Check the tyre pressure regularly.
x Inflate the tyres with air to at least the lower tyre pressure limit and no more than
the upper limit.
x Use a pump with a pressure display when inflating the tyres.
Tyre pressure conversion
psi bar psi bar
12 0.8 80 5.5
15 1.5 90 6.2
Cycle Wheels and tyres
83
Tyre pressure conversion
psi bar psi bar
30 2.1 100 6.9
40 2.8 110 7.6
50 3.5 120 8.3
60 4.1 130 9.0
70 4.8 140 9.7
10.2 Rims and spokes
Spokes with uniform tension are required in order for a wheel to run true. The tension
of individual spokes may be altered by riding too quickly over obstacles such as kerbs,
or if a spoke nipple comes loose. Wheel trueness and rim stability are reduced when
individual spokes are damaged or no longer taut.
WARNING
Risk of falling due to locked up rim brakes or wobbly wheels in
the event of rim run-out.
Risk of accident and injury!
x Only use true-running wheels.
x Have loose spokes tensioned by your dealer.
x Have your dealer centre untrue wheels immediately.
10.3 Fitting and removing the front/rear wheel
WARNING
Risk of falling due to wheels loosening if quick-release axles are
not fastened.
Risk of accident and injury!
x Before every ride, check that the wheels are securely inserted
in the fork ends.
CycleWheels and tyres
84
WARNING
Wheel drop-out due to loosened fastenings.
Risk of accident and injury!
x Check the wheel fastenings before every ride.
CAUTION
Risk of burning due to hot brake discs!
Risk of injury!
x Always let the brake discs cool down before opening the
quick release.
NOTE
Damage to the brake due to removing the front or rear wheel.
Risk of damage!
x If you lack the necessary expertise and the tools required,
have the front or rear wheel removed and fitted by your dealer
only.
Depending on the cycle model, the wheels are fastened in the fork ends with
quick-release axles or thru-axles.
x If you lack the necessary expertise and the tools required to adjust quick-release
axles, contact your dealer.
Cycle Wheels and tyres
85
The cycle may be equipped with
conventional thru-axles, lever-type thru-axles
or quick-release axles. The axles can be
replaced with anti-theft axles.
Axles pass through the wheels and are
fastened between the fork ends of the
cycle. The fork ends may be open or closed
depending on the front fork model. These
have different fitting and removal methods.
Thru-axles and quick-release axles can be fitted with anti-theft devices or
replaced with axles that feature integrated anti-theft protection.
Wheels may be secured in various ways depending on the model:
Some models cannot be unfastened while the cycle is in an upright position.
With some models, a dedicated tool is required to loosen the hub axle nut or
quick-release adjusting nut.
x Ask your dealer about anti-theft thru-axle and quick-release axle options.
x Refer to the information enclosed by the manufacturer about fitting the axles.
x If you lack the necessary expertise and the tools required to adjust quick-release
axles, contact your dealer.
A B
Illustr.: Open (A) and closed (B) fork ends
(example)
CycleWheels and tyres
86
10.3.1 Front/rear wheels with quick-release axles
10.3.1.1 Fitting
Models with open fork ends:
1. Push the quick-release axle through the
wheel hub and give the quick-release
adjusting nut one or two turns to screw
it onto the quick-release axle.
2. Insert the front/rear wheel and quick
release into the fork ends.
x If applicable, follow the
specifications regarding the front/
rear wheel running direction. This
specification generally relates to the
tyre tread and can be found on the
sidewall of the tyre.
3. Pull the quick-release lever inwards
until it touches the front fork or the
frame (see “Illustr.: Wheel with a
quick-release axle”).
x If the quick-release axle or the front/rear wheel is not firmly in place, or if you
can pull the quick release without any effort, readjust the tension
(see the “Basic adjustments / Quick releases” chapter).
Models with closed fork ends:
1. Align the front/rear wheel between the fork ends so that the fork ends and wheel
hub form a straight line.
x If applicable, follow the specifications regarding the front/rear wheel running
direction. This specification generally relates to the tyre tread and can be found
on the sidewall of the tyre.
2. Push the thru-axle through the fork ends and the wheel hub.
3. Screw the quick-release axle into the quick-release adjusting nut by turning it
clockwise with the lever until hand-tight.
4. Pull the quick-release lever inwards until it touches the front fork or the frame
(see “Illustr.: Wheel with a quick-release axle”).
x If the quick-release axle or the front/rear wheel is not firmly in place, or if you can
pull the quick release without any effort, readjust the tension
(see the “Basic adjustments / Quick releases” chapter).
Illustr.: Wheel with a quick-release axle
(example)
1 Quick-release adjusting nut
2 Quick-release axle lever
1
2
Cycle Wheels and tyres
87
10.3.1.2 Removal
Models with open fork ends:
1. To unfasten the quick-release axle, pull the axle lever outwards.
2. Remove the front/rear wheel from the fork ends.
Models with closed fork ends:
1. To unfasten the quick-release axle, pull the axle lever outwards.
2. Unscrew the quick-release axle from the quick-release adjusting nut and remove
the nut.
3. Secure the front/rear wheel.
4. Pull the quick-release axle out of the fork ends and wheel hub.
5. Remove the front/rear wheel.
10.3.2 Front/rear wheels with conventional thru-axles
10.3.2.1 Fitting
Models with open fork ends:
1. Push the thru-axle through the wheel
hub and give the hub axle nut one or
two turns to screw it onto the thru-axle.
2. Insert the front/rear wheel and thru-axle
into the fork ends.
x If applicable, follow the
specifications regarding the front/
rear wheel running direction.
This specification generally relates
to the tyre tread and can be found
on the sidewall of the tyre.
3. Fix the hub axle nut in place using a
suitable tool and tighten the thru-axle
by turning it clockwise with a torque
wrench.
1
2
Illustr.: Wheel with a thru-axle (example)
1 Hub axle nut
2 Thru-axle
CycleWheels and tyres
88
Models with closed fork ends:
1. Align the front/rear wheel between the fork ends so that the fork ends and wheel
hub form a straight line.
x If applicable, follow the specifications regarding the front/rear wheel running
direction. This specification generally relates to the tyre tread and can be found
on the sidewall of the tyre.
2. Push the thru-axle through the fork ends and the wheel hub.
3. Screw the hub axle nut clockwise onto the thru-axle until hand-tight.
4. Fix the hub axle nut in place using a suitable tool and tighten the thru-axle by
turning it clockwise with a torque wrench.
10.3.2.2 Removal
Models with open fork ends:
1. Loosen the hub axle nut until you can move the thru-axle between the fork ends.
2. Remove the front/rear wheel and thru-axle from the fork ends.
Models with closed fork ends:
1. Unscrew the thru-axle from the hub axle nut using a suitable tool, and remove the
nut.
2. Secure the front/rear wheel.
3. Pull the thru-axle out of the fork ends and wheel hub.
4. Remove the front/rear wheel.
10.3.3 Front/rear wheels with lever-type thru-axles
10.3.3.1 Fitting
Models with open fork ends:
1. Push the thru-axle through the wheel hub and give the hub axle nut one or two
turns to screw it onto the thru-axle.
2. Insert the front/rear wheel and thru-axle into the fork ends.
x If applicable, follow the specifications regarding the front/rear wheel running
direction. This specification generally relates to the tyre tread and can be found
on the sidewall of the tyre.
Cycle Wheels and tyres
89
3. Screw the thru-axle into the hub axle
nut by turning it clockwise with the lever
until hand-tight.
x Make sure that the front/rear wheel
can then no longer move sideways.
4. Afterwards, pull the lever into position so
that it touches the front fork.
Models with closed fork ends:
1. Align the front/rear wheel between the fork ends so that the fork ends and wheel
hub form a straight line.
x If applicable, follow the specifications regarding the front/rear wheel running
direction. This specification generally relates to the tyre tread and can be found
on the sidewall of the tyre. Push the thru-axle through the fork ends and the
wheel hub.
2. Screw the thru-axle into the hub axle nut by turning it clockwise with the lever until
hand-tight.
x Make sure that the front/rear wheel cannot move sideways.
3. Afterwards, pull the lever into position so that it touches the front fork.
10.3.3.2 Removal
Models with open fork ends:
1. Loosen the hub axle nut until you can move the thru-axle between the fork ends.
2. Remove the front/rear wheel and thru-axle from the fork ends.
Models with closed fork ends:
1. Unscrew the thru-axle from the hub axle nut.
2. Secure the front/rear wheel.
3. Pull the thru-axle out of the fork ends and wheel hub.
4. Remove the front/rear wheel.
1
2
Illustr.: Wheel with a lever-type thru-axle
(example)
1 Hub axle nut
2 Thru-axle lever
CycleWheels and tyres
90
10.3.4 Carbon wheels
Carbon wheels, made from carbon fibre reinforced plastic, are notable for their high
rigidity and low weight. Rims with higher sidewalls also have particular aerodynamic
qualities.
If your cycle is equipped with carbon wheels, refer to the specifications on
the frame or ask your dealer about the maximum gross weight limit for the
cycle.
WARNING
Reduced brake action due to moisture on carbon rims.
Risk of accident and injury!
x Do not use carbon wheels in the wet.
NOTE
Rim deformation or tyre blow-out due to the heat generated while
braking e.g. when riding downhill in the mountains.
Risk of damage!
x Use both brakes for longer periods of braking.
x Release the brakes at regular intervals for a while so that the
brake pads and rims can cool down.
x Only use brake pads that are suitable for carbon wheels.
x Keep off the road while you practice braking with carbon wheels.
x Note that brake pads for carbon wheels wear more quickly than other brake pads.
x Note that brake pads for carbon wheels are heat-sensitive and not suitable for
prolonged braking, e.g. on long descents. Ensure you have regular cooling periods
with no brake operation.
Cycle Telescopic seat post
91
11 Telescopic seat post
This chapter contains information about the basics of telescopic seat posts, as well as
their adjustment and operation.
11.1 Basics
WARNING
Inattention on the road.
Risk of accident and injury!
x Familiarise yourself with the features of the telescopic seat
post before your first ride.
x Only operate the telescopic seat post if it will not take any of
your attention off the road and terrain.
x Stop if you cannot operate the telescopic seat post safely.
WARNING
Loss of eyesight on contact with hydraulic fluid.
Risk of accident and injury!
x If hydraulic fluid gets in your eye, rinse it out with clean water
straight away.
x Contact a doctor immediately after contact with hydraulic
fluid.
Depending on the cycle model, there may be a telescopic seat post installed. A telescopic
seat post allows the saddle height to be adjusted by operating a lever underneath the
saddle or a remote control on the handlebars, both at a standstill and while riding.
Height adjustments may be stepped or stepless, depending on the design of the
telescopic seat post. When the handlebar remote control is operated, this is transmitted
to the telescopic seat post either mechanically, hydraulically or via a wireless signal.
x Refer to information from the telescopic seat post manufacturer.
x If you lack the necessary expertise or the tools required to adjust, maintain or
operate the telescopic seat post, contact your dealer.
CycleTelescopic seat post
92
11.2 Adjustments
11.2.1 Adjusting the cable tension
If your cycle has a mechanical remote control:
The cable tension for the telescopic seat post remote control must be adjusted in the
event of a malfunction, for example if the saddle height cannot be adjusted or if the
saddle height changes despite not operating the lever or button.
x Refer to information from the manufacturer about adjusting the cable tension.
11.2.2 Adjusting the extension speed
The extension speed for the telescopic seat post is generally adjusted using the speed
Adjustment screw on the remote control. The extension speed is reduced or increased
depending on the turning direction.
x Refer to information from the manufacturer about adjusting the extension speed.
11.2.3 Telescopic seat post remote control position
The position of the telescopic seat post remote control must be custom-adjusted so that
the lever or button can be operated easily and safely (see “Illustr.: Remote control position”).
x If you lack the necessary expertise or the tools required, have your dealer adjust
the remote control position to suit your needs.
1. Loosen the remote control screw by
turning it anticlockwise.
2. Position the remote control so that the
lever or button is easily accessible while
riding.
3. Tighten the remote control screw by
turning it clockwise.
Illustr.: Remote control position (example)
Cycle Suspension
93
11.2.4 Adjusting a pneumatic telescopic seat post
Air pressure influences factors such as the extension speed and the force that must be
exerted in order to lower the telescopic seat post. The air pressure inside the pneumatic
telescopic seat post is pre-set by the manufacturer and only needs to be adjusted in the
event of a malfunction.
x Have the telescopic seat post adjusted by your dealer.
11.2.5 Bleeding a hydraulic telescopic seat post
A hydraulic telescopic seat post must be bled once it stops fully extending or the saddle
starts to sink after the lever is released.
x Have the telescopic seat post bled by your dealer.
11.3 Operation
Depending on the design of the telescopic seat post, the remote control may be
equipped with one or two levers. Where there are two levers, each lever is generally
associated with a point between the upper and lower saddle positions.
x To lower the saddle, place weight on it and operate the lever. Once the saddle has
reached the desired position, release the lever.
x To raise the saddle, take the weight off it and operate the lever. Once the saddle
has reached the desired position, release the lever.
12 Suspension
This chapter contains information about the basics of suspension elements, as well as
their adjustment and operation.
If suspension elements are too soft, they will no longer provide cushioning against
bumps and the suspension will bottom out.
Suspension elements must be adjusted or tuned to prevent bottoming out.
If a suspension element frequently bottoms out, it (and often the frame too) will become
permanently damaged.
x If you lack the necessary expertise and the tools required for the adjustments, have
suspension elements adjusted by your dealer.
CycleSuspension
94
12.1 Suspension seat post
Depending on the cycle model, the cycle may
be equipped with a suspension seat post.
Suspension seat posts increase comfort
and safety when riding over uneven ground.
The suspension seat post must be adjusted
to the rider’s body weight. This requires
expertise, and it may be necessary to replace
the springs.
12.2 Suspension fork and rear suspension
12.2.1 Basics
Depending on the cycle model, the cycle may be equipped with a suspension fork and/
or rear suspension.
Suspension forks absorb impacts to the front
wheel and increase comfort as well as safety
when riding over uneven ground. The
suspension fork must be tuned to the
intended use and the rider’s weight.
Illustr.: Suspension seat post (example)
1 Suspension inside
1
Illustr.: Suspension fork (example)
1 Suspension fork stanchion leg
2 Suspension fork lower leg
1
2
Cycle Suspension
95
Rear suspension, which is installed centrally
between the front and rear frame, absorbs
impacts to the rear wheel and increases
comfort as well as safety when riding over
uneven ground. The rear suspension must
be tuned to the intended use and the rider’s
weight. Rear suspension increases comfort
when riding over uneven ground.
x If your cycle is equipped with
adjustable rear suspension, refer to the
adjustment information enclosed by the
manufacturer.
12.2.2 Adjustments
The following adjustment options are generally available:
Compression and rebound
Sag (compression under body weight)
Lockout (suspension locking feature)
12.2.2.1 Compression and rebound
Adjusting the compression and rebound influences the damping or response behaviour
of the suspension fork or rear suspension. The ratio between compression and rebound
is crucial. Depending on the cycle model, the suspension may only be equipped for
rebound adjustment. The ratio between compression and rebound is determined by the
condition of the road. A correctly adjusted ratio ensures optimum contact between the
wheels and the ground.
x Have the compression and rebound adjusted by your dealer.
12.2.2.2 Sag
Sag is the amount of compression caused by the rider’s body weight. Depending on the
model of the suspension fork or rear suspension, and depending on the intended use,
the sag is adjusted to a value between 15 % and 40 % of the total suspension travel.
Sag is influenced by the spring preload. When the sag is optimally adjusted, the
suspension will compress by 15 % to 40 % of its travel when the rider sits on the cycle.
The sag is determined by the spring preload or by the adjustable air pressure in the
suspension fork or damper. The spring preload or the air pressure therefore determine
the stiffness of the suspension and whether the chassis is hard or soft.
x Have your dealer adjust the suspension fork or rear suspension to your body
weight and riding style.
L
6
0
-
5
8
4
2
3
-
5
0
p
s
i
1
6
0
-
3
5
0
k
P
a
1
,
6
-
3
,
5
B
a
r
2
1
Illustr.: Rear suspension (example)
1 Spring stiffness adjustment
2 Damping adjustment
CycleSuspension
96
Have your dealer adjust the suspension fork / damper sag to suit your body
weight and riding style. This is usually dealt with through air pressure or by
replacing suspension elements.
12.2.2.3 Lockout
The lockout feature locks the suspension fork. This can reduce bob or squat in the front
fork, e.g. where the suspension sinks when pedalling hard.
Depending on the cycle model, the rear suspension may also be equipped with a
lockout feature.
Bumps cause the suspension fork to compress slightly even when locked.
This is for technical reasons and protects the front fork against damage.
12.2.3 Operation
NOTE
Increased wear due to lockout use.
Risk of damage!
x Only use the lockout on even roads.
x Only use the lockout if it improves handling.
x Refer to the information enclosed by the manufacturer about operating suspension
forks.
x To lock the suspension fork, turn the knob anticlockwise until it stops.
x To unlock the suspension fork, turn the knob clockwise until it stops (see “Illustr.:
Suspension fork lockout control”).
x Check whether the rear suspension can be locked. If necessary, ask a professional
how the rear suspension is locked and unlocked.
Cycle Suspension
97
Illustr.: Suspension fork lockout control (top view, example).
On models with a mechanical suspension element:
x To increase the spring preload and so adjust the sag to a lower level, turn the knob
on the suspension fork or rear suspension in the “+” direction
(see “Illustr.: Suspension fork knob”).
x To reduce the spring preload and so adjust the sag to a higher level, turn the knob
on the suspension fork in the “–” direction.
x If you lack the necessary expertise and the tools required to optimally adjust the
sag, have the suspension adjusted by your dealer.
Illustr.: Suspension fork knob (top view, example).
On models with air chambers:
x To adjust the spring preload, increase or reduce the air pressure in the suspension
fork.
x To increase or reduce the suspension fork air pressure, you will need a dedicated
damper pump.
x If you lack the necessary expertise and the tools required for the adjustments, have
suspension elements adjusted by your dealer.
CycleCleaning
98
13 Cleaning
CAUTION
Pinching and crushing of body parts by moving components.
Risk of injury!
x Be careful when handling moving parts so as not to get your
fingers caught.
x Wear protective gloves if necessary.
NOTE
Use of incorrect cleaners.
Risk of damage!
x Do not use abrasive cleaning products.
x Do not use sharp, angular or metallic cleaning tools.
x Do not use strong jets of water or high-pressure equipment to
clean the cycle.
What you need for cleaning and maintenance:
Clean cloths
Mild, lukewarm soapy water
A soft brush or sponge
Cleaners and preservers
Universal oil
x If necessary, consult your dealer about suitable cleaners and preservers.
x Clean the cycle regularly, even if it is only slightly dirty.
x Wipe all surfaces and components with a damp sponge.
x Use mild soapy water to moisten the sponge.
x Wipe all surfaces and components dry after cleaning.
x Preserve all paintwork and metallic surfaces on the frame at least every six months.
Cycle Cleaning
99
x Do not preserve the rims if you have rim brakes, or the brake discs if you have disc
brakes.
x Refer to and follow the notes in the information enclosed by the manufacturer
about cleaning individual components.
13.1 Brakes
CAUTION
Risk of burning due to hot brake discs.
Risk of injury!
x Wait until the brake discs have cooled down before touching
them.
CAUTION
Diminished brake action due to soap residue, oil, grease or care
products on the rims or brake blocks, or on the brake discs or
brake pads.
Risk of accident and injury!
x Avoid grease and oil contact with the rim, brake disc, brake
blocks or brake pads.
x Do not use the cycle if grease or oil has touched the rim,
brake disc, brake blocks or brake pads.
Have oil-contaminated components professionally cleaned,
and if necessary replaced by your dealer.
x Remove soap and care product residue after cleaning.
x Check the brakes for soap and care product residue after
cleaning.
x Remove dirt from the brake components, brake calliper and rim immediately with a
slightly damp cloth and if necessary a little brake cleaner.
CycleCleaning
100
13.2 Suspension
If the cycle is equipped with a suspension fork, a suspension seat post or rear
suspension:
1. Remove dirt from the sliding surfaces and the adjacent seals immediately with a
clean cloth, lightly oiled if necessary (see “Illustr.: Suspension fork sliding surface”
and “Illustr.: Suspension seat post sliding surface”).
2. Oil the sliding surface with a little universal oil after cleaning.
3. Compress and extend the suspension five times. Then remove excess oil with a
clean cloth.
Illustr.: Suspension seat post sliding surface (example)
1 Sliding surface
1
Illustr.: Suspension fork sliding surface (example)
1 Sliding surface
1
Cycle Cleaning
101
13.3 Gear shifting system
NOTE
Incorrectly chosen grease, oil and care products can damage the
components.
Risk of damage!
x Consult your dealer about the use of greases, oils and care
products, particularly with derailleur shifting systems.
x Do not use water for cleaning, and do not use chemical brake
cleaners or thinners.
x Do not use gun oil or rust removal spray.
x Clean the controls for the gear shifting
system with a damp cloth.
x Clean the moving components in
derailleur shifting systems with a damp
cloth or a soft brush, provided they are
easily accessible (see “Illustr.: Moving
components of a derailleur shifting
system”).
x Oil the moving components in derailleur
shifting systems with a little universal oil
after cleaning, provided they are easily
accessible.
x Then remove excess oil with a clean
cloth.
13.4 Chain
x If the cycle is equipped with an all-round chain guard, have your dealer explain how
to remove and fit the guard, or have them remove and fit it for you.
Remove dirt from the bike chain with a clean cloth, lightly oiled if necessary.
x Remove dirt from the sprockets and chainrings with a small, soft brush.
x Oil the chain with a little universal oil at regular intervals, after cleaning and after
riding in the rain.
x Contact your dealer regarding stubborn dirt.
Illustr.: Moving components of a derailleur
shifting system (example)
1 Rear derailleur
2 Jockey wheels
3 Chain adjuster
1
3
2
CycleMaintenance
102
14 Maintenance
WARNING
Brake failure or material breakage due to incorrect maintenance
and inspection.
Risk of accident and injury!
x Do not carry out any maintenance on the cycle if you lack the
necessary expertise and the tools required.
x Have the cycle regularly checked by your dealer as well.
CAUTION
Risk of burning due to hot brake discs.
Risk of injury!
x Let the brake discs cool down before maintenance.
CAUTION
Material fatigue and material breakage due to tightening screw
joints incorrectly.
Risk of accident and injury!
x Loose screw joints must be properly tightened with a torque
wrench.
x Loose screw joints must be tightened using the correct
torques.
x Have your dealer tighten loose screw joints.
Cycle Maintenance
103
CAUTION
Alterations to the cycle and incorrectly chosen spare parts can
cause the cycle to malfunction.
Risk of accident and injury!
x Consult your dealer about suitable spare parts.
x Only use original spare parts.
NOTE
Dripping oil or grease.
Pollution!
x Ensure that there is no dripping oil or grease.
x Clear up spilled oil or grease immediately with a cloth.
x Dispose of spilled oil or grease residue in an environmentally
friendly manner, according to applicable national and regional
regulations.
NOTE
Oil or grease on the cycle can transfer onto clothes.
Risk of damage!
x Remove excess oil or grease with a cloth after cycle care.
x Keep your clothes away from oil and grease.
Consult your dealer about suitable spare parts before fitting.
CycleMaintenance
104
What you need for maintenance:
Clean cloths
Preservers
Universal oil
x If necessary, consult your dealer about suitable lubricants and preservers.
x Have all maintenance and repairs documented by your dealer.
x If you find damage, do not use the cycle and have it checked or repaired by your
dealer.
x Have loose screw joints checked by your dealer if you lack the necessary expertise
and the tools required.
14.1 Inspection intervals
x Have your dealer inspect the cycle at the following intervals:
Inspection intervals
Inspection Distance travelled Hours of operation Duration of use
1st inspection after 300 km/
190 mi* or
after 15 hours of
operation* or
after 3 months*
2nd inspection after 2,000 km/
1,250 mi* or
after 100 hours of
operation* or
after one year*
Each subsequent
inspection
after a further
2,000 km/1,250 mi*
or
after a further 100 hours
of operation* or
after a further year*
* whichever is the earliest
x If you use the cycle in difficult conditions or ride more than 2,000 km/1,250 mi
per year, shorten the inspection intervals and have an inspection carried out by
your dealer every 6 months.
Examples of difficult conditions include:
Frequent use on demanding terrain
Operation in poor weather conditions, e.g.:
in winter: particular risk of corrosion due to salt on the roads
in mud or slush: increased wear due to excessive dirt in moving parts
Operation with constant heavy loads
x Follow the inspection interval specifications in the manuals enclosed with the
various cycle components.
x Carry out the following maintenance work once a month or after a fall.
Cycle Maintenance
105
Please note that in the event of guarantee claims, Winora-Staiger GmbH/Haibike USA
reserve the right to check whether the fault which occurred could have been avoided
through proper maintenance. Depending on the result, we reserve the right to reject the
guarantee claim if necessary.
Your cycle has a variety of parts that require particular attention, especially with regard to
their exposure to dirt, dust or moisture, or simply because of their relevance to safety.
It is therefore in your own interest to observe the inspection intervals.
14.2 Screw joints
x Check the cycle for loose screw joints (visual inspection).
x Do not ride the cycle if you find loose screw joints.
x Have loose screw joints checked by your dealer if you lack the necessary
expertise and the tools required.
14.3 Frame and rigid fork
x Check the frame and rigid fork for cracks, deformation or discolouration.
x If the frame or the rigid fork is cracked, deformed or discoloured, contact your
dealer immediately.
x Do not use the cycle if you find any cracks, deformation or discolouration.
14.4 Suspension fork
x Check the suspension fork for cracks, deformation or discolouration.
x If the suspension fork is cracked, deformed or discoloured, contact your dealer
immediately.
x Compress and extend the suspension fork.
x If you hear unusual noises or the suspension fork gives way without any
resistance, have it checked by your dealer.
x Clean and oil the suspension fork (see the “Cleaning” chapter).
CycleMaintenance
106
14.5 Luggage carrier and mudguards
1. Hold the cycle firmly by the frame.
2. Pull the luggage carrier back and forth to check that all the screw joints are tight
and do not move.
3. Pull the mudguards back and forth to check that they are firmly in place.
x Tighten loose screw joints in a clockwise direction. Ensure that the torques are
correct.
x Have loose screw joints checked by your dealer if you lack the necessary
expertise and the tools required.
14.6 Saddle
x Check whether you can twist the saddle.
x If you can twist the saddle, tighten the seat post clamp. Observe applicable
torques.
x Have the seat post clamp checked by your dealer if you lack the necessary
expertise and the tools required.
x If there is a quick release installed on the seat post clamp, adjust the quick
release (see the “Basic adjustments / Quick releases” chapter).
x Check whether you can move the saddle horizontally in the direction of travel or in
the opposite direction.
x If you can move the saddle, adjust the saddle clamp (see the “Basic
adjustments / Saddle / Adjusting the reach” chapter).
14.7 Handlebars and handlebar stems
x Check whether the handlebars are
aligned perpendicularly to the front wheel
(see “Illustr.: Correct handlebar alignment”).
x Readjust the handlebars if they
are not perpendicular to the front
wheel (see the “Basic adjustments /
Handlebars and handlebar stems /
Aligning the handlebars” chapter).
x Fix the front wheel in place by clamping it between your legs to prevent it
twisting sideways, and check whether the handlebars can be turned relative to
the front wheel. Ensure that you do not touch hot brake discs.
x If you can turn the handlebars, have them adjusted by your dealer.
Illustr.: Correct handlebar alignment (example)
Cycle Maintenance
107
x Check whether the handlebar stem can be moved up and down.
x If you detect play in the head tube or handlebar stem when pulling the stem up
and down, have the bearing play or the handlebar stem adjusted by your dealer.
x Check the handlebars and handlebar stem for cracks, deformation or discolouration.
x If the handlebars or handlebar stem are cracked, deformed or discoloured,
stop using the cycle and contact your dealer.
14.8 Adjusting the headset
CAUTION
Unexpected cycle behaviour due to incorrect adjustment.
Risk of accident and injury!
x Observe applicable torques.
x Observe the minimum insertion depth for the handlebar stem.
CAUTION
Risk of burning due to hot brake discs.
Risk of injury!
x Let the brake discs cool down before maintenance.
In a traditional internal clamping mechanism for the handlebar stem, the bearing race is
secured with a washer and lock nut.
In a non-threaded external clamping mechanism, the bearing race is secured by the
handlebar stem itself.
There is very little play when adjusting the headset. The bearings can easily become
blocked or damaged.
Special tools are required to adjust headsets.
x Refer to and follow information from the headset manufacturer.
x If you lack the necessary expertise and the tools required to adjust the headset,
contact your dealer.
Excessive tightness can damage the headset and block the steering
movement, which negatively affects handling characteristics.
CycleMaintenance
108
14.8.1
Conventional handlebar stem with an internal clamping mechanism
If there is too much play in the headset, follow the steps described below:
1. Loosen the upper lock nut.
2. Turn the bearing race underneath
slightly clockwise.
3. Tighten the upper lock nut. Observe the
permitted torque.
4. Check the headset play.
x If there is still play in the headset,
repeat steps 1 to 4.
5. Check whether the handlebar stem is
secure by fixing the front wheel in place
between your legs and attempting to
turn the handlebars relative to it.
6. Check the handlebar position after adjusting the headset (see the “Basic
adjustments / Handlebars and handlebar stems / Aligning the handlebars” chapter).
14.8.2 Handlebar stem with an external clamping mechanism
1. Unfasten the clamp bolts on the side of
the handlebar stem.
2. Remove the cap from the head of the
inner adjustment screw, if necessary.
3. Tighten the inner adjustment screw
further by turning it a fraction clockwise
if there is a lot of play in the headset.
4. Align the handlebar stem so that the
handlebars are perpendicular to the
front wheel.
5. Re-tighten the clamp bolts with the
permitted torque.
6. Check the headset play by placing two fingers around the upper head race, pulling
the front brake and pushing the cycle forwards and backwards.
The fork stem must not move in the head tube as you do this.
x If there is still play in the headset, repeat steps 1 to 5.
7. Check how freely the handlebars move. If the steering is heavier than before, then
the headset adjustment screw is too tight. Start again at step 1 and turn the inner
adjustment screw a fraction anticlockwise.
Illustr.: Internal clamping mechanism (example)
1 Lock nut
2 Bearing race
1
2
Illustr.: External clamping mechanism (example)
1 Inner adjustment screw
2 Clamp bolts
1
2
Cycle Maintenance
109
8. Check whether the handlebar stem is secure by fixing the front wheel in place
between your legs and attempting to turn the handlebars relative to it.
9. Check the handlebar position after adjusting the headset (see the “Basic
adjustments / Handlebars and handlebar stems / Aligning the handlebars” chapter).
14.9 Wheels
x Check whether the front or rear wheel can be moved sideways, and whether the
wheel nuts move.
x If the wheel nuts move, have the screw joints checked by your dealer.
x If the quick-release axle moves, adjust the axle (see the “Wheels and tyres /
Fitting and removing the front/rear wheel” chapter).
x If the front or rear wheel moves sideways, have the wheel repaired by your
dealer.
x Check whether there is equal distance on both sides between the front wheel and
the front fork or between the rear wheel and the frame.
x If the distances are not equal, have the front or rear wheel checked by your
dealer.
x Lift the cycle and turn the front or rear wheel. Check whether the front or rear
wheel swings sideways or outwards.
x If the front or rear wheel swings sideways or outwards, have the wheel
checked by your dealer.
14.9.1 Rims and spokes
x Check the front and rear rims for cracks, deformation or discolouration.
x Do not use the cycle if a rim is cracked, deformed or discoloured.
x Have the rim checked by your dealer.
x Squeeze the spokes together gently with your thumb and fingers, checking
whether the tension is the same for all spokes.
x If the tension varies or spokes are loose, have the spokes tensioned by your
dealer.
CycleMaintenance
110
14.9.2 Rim wear indicator with rim brakes
The wear indicator is a groove in the surface of the rim where the brake pads are
pressed. The wear limit is reached when the surface groove can no longer be felt,
i.e. has been worn away through braking.
x Check whether there is a wear indicator
on the rims of your cycle
(see “Illustr.: Rim with a wear indicator”).
1. If your cycle rims have an indentation,
check whether the wear limit has been
reached.
2. Stroke your fingernail vertically across
the indentation.
x If you cannot feel the indentation,
do not use the cycle.
x Have the rims replaced by your
dealer.
14.9.3 Tyres
1. Check whether the tyre pressure is correct (see the “Wheels and tyres / Tyres and
valves / Tyre pressure” chapter).
2. Check the tyres for cracks and damage from foreign bodies.
3. Check whether you can clearly feel the tyre tread.
x If a tyre is cracked or damaged, or the tread depth is too low, have the tyre
replaced by your dealer.
The following sentence is only applicable for Europe:
x On an S-pedelec, ensure that the profile depth does not fall below 1 mm.
4. Check whether the valves are firmly in place and tighten the lower knurled nut if
necessary by turning it clockwise.
5. Check whether the valves have a protective cap.
x Replace missing protective caps so that dust and dirt cannot get into the
valves.
Illustr.: Rim with a wear indicator (example)
1 Indentation
1
Cycle Maintenance
111
14.10 Flat tyre
A flat tyre is the most frequent cause of cycling breakdowns. A flat tyre need not end
your ride if you carry the necessary tools and a replacement inner tube or repair kit.
For detailed instructions on repairing a flat tyre, see the “Maintenance / Removing the
wheel” chapter.
14.11 Removing the wheel
Before you remove a wheel, read the “Wheels and tyres” chapter.
If you lack the necessary expertise and the tools required, contact your dealer.
x On cycles with a derailleur shifting system, shift to the smallest sprocket in the
cassette at the back. This will position the rear derailleur on the outside and
prevent it hindering the removal process.
x To facilitate wheel removal, fix the cycle in place using a suitable work stand if
necessary.
14.11.1 Preparing the brakes
CAUTION
Risk of burning due to hot brake discs.
Risk of accident and injury!
x Let the brake discs cool down before removing the wheel.
NOTE
Locked up brake pads due to operating the disc brake
incorrectly.
Risk of damage!
x Never pull the brake lever when a wheel is removed.
Always use the transport locks when you remove a wheel.
CycleMaintenance
112
Before the wheels can be removed, the brakes must be prepared.
Refer to the information enclosed by the brake and shifting system
manufacturers.
14.11.1.1 Preparing mechanical rim brakes
1. Detach the brake cable from the brake arm.
2. Reach around the wheel with one hand and press the brake pads or brake arms
together. This position allows you to easily detach the cable nipple (normally
cylindrical) or V-brake outer cable.
1
2
5
4
3
6
2
1
5
4
3
6
Illustr.: Rim brake with a cable nipple
(example)
1 Cable nipple
2 Brake arm
3 Tyre
4 Rim
5 Brake block holders
6 Spring preload adjustment screw
Illustr.: Rim brake with a cable
guide
(example)
1 Cable guide
2 Brake arm
3 Tyre
4 Rim
5 Brake block holders
6 Spring preload adjustment screw
Cycle Maintenance
113
14.11.1.2 Preparing hydraulic rim brakes
x To open the quick-release lever for
hydraulic rim brakes, flip the
quick-release lever down (see “Illustr.:
Preparing hydraulic rim brakes”).
x Pull the brake from the retaining boss.
14.11.1.3 Preparing the coaster brake
x With coaster brakes, loosen the screw
joint between the reaction arm and the
chain stays.
x Remove the shift cables or shift box
before removing the wheel. Refer to
information from the manufacturer
about fitting and removal.
Illustr.: Preparing hydraulic rim brakes
(example)
1 2
Illustr.: Coaster brake (example)
1 Chain stays
2 Fastening clamp on the frame
3 Screw joint
4 Coaster brake reaction arm
3 4
CycleMaintenance
114
14.11.1.4 Preparing the brakes on racing bikes
Before the wheels can be removed, the brakes must be prepared.
x Open the quick-release lever on the rim
brake.
14.11.2 Removing the front wheel
x Open the quick-release lever (see the “Wheels and tyres / Fitting and removing the
front/rear wheel” chapter) or loosen the cap nuts.
If the front wheel cannot be pulled out yet, this is due to the drop-out locks. These are
retaining collars in the fork end.
x Unfasten the nut on the quick release or unscrew the cap nut further from the axle.
x Slip the front wheel from the drop-out locks.
14.11.3 Removing the rear wheel
x On cycles with a derailleur shifting
system, shift to the smallest rear
sprocket.
x To facilitate rear wheel removal with
derailleur shifting systems, pull the
rear derailleur backwards slightly by
hand (see “Illustr.: Pulling back the rear
derailleur”).
x Lift the cycle up a little and give the rear
wheel a light tap so that it drops down
and out.
1
Illustr.: Preparing the brakes on racing bikes
(example)
1 Rim brake quick-release lever
Illustr.: Pulling back the rear derailleur (example)
Cycle Maintenance
115
If the cycle is equipped with a rear derailleur that features a chain adjuster lock:
x Use the lever on the top of the rear derailleur to deactivate the derailleur before
removing the rear wheel.
If the cycle has thru-axles, refer to the “Wheels and tyres / Fitting and removing the front/
rear wheel” chapter.
x Have your dealer explain how to use thru-axles if necessary.
If the cycle has a combination of hub and derailleur shifting systems, then the shift box
must be removed first before removing the rear wheel as with a derailleur shifting system.
x Refer to information from the manufacturer about fitting and removing the shift box.
x Have the shift box fitted and removed by your dealer if you lack the necessary
expertise and the tools required.
14.11.4 Removing clincher or folding tyres
NOTE
Damage to the inner tube due to a ruined or worn tyre.
Risk of damage!
x If the fabric of a tyre has been ruined by a foreign body or
wear, replace the tyre.
To remove clincher or folding tyres, follow these steps:
1. Unscrew the valve cap and lower knurled nut from the valve
(see “Illustr.: Removing clincher or folding tyres (A)”).
2. Completely deflate the inner tube.
3. Press the tyre from the rim sidewall towards the centre of the rim around the entire
circumference of the tyre.
4. Push one tyre lever between the tyre and rim approximately 5 cm/2.0" to the right
of the valve.
5. Lever the sidewall of the tyre over the edge of the rim and hold the tyre lever firmly
in this position.
6. Push the second tyre lever between the tyre and rim approximately 5 cm/2.0" to
the left of the valve (see “Illustr.: Removing clincher or folding tyres (B)”).
7. Lever the sidewall of the tyre over the edge of the rim with the second tyre lever.
8. Push the second tyre lever along the rim to completely release the rim sidewall.
CycleMaintenance
116
If you are repairing the tyre while out riding:
1. Pull the inner tube out of the wired or clincher tyre (see “Illustr.: Removing clincher
or folding tyres (C)”) without fully removing it from the tyre.
2. Inflate the inner tube and try to locate the leak by sound and feel.
3. Check the tyre for foreign bodies and remove them.
4. Repair the inner tube using a repair kit. Refer to the tyre repair information enclosed
by the manufacturer.
If you are repairing the tyre at home:
1. Pull the inner tube out of the clincher or folding tyre
(see “Illustr.: Removing clincher or folding tyres (C)”).
2. Inflate the inner tube and immerse it in water to locate the leak by seeing where
bubbles escape.
3. Repair the inner tube using a repair kit. Refer to the tyre repair information enclosed
by the manufacturer.
x If the inner tube is beyond repair, insert a new one.
4. Check the tyre for foreign bodies and remove them.
x Replace the tyre if it is too badly damaged.
A
B C
Illustr.: Removing clincher or folding tyres (example)
Cycle Maintenance
117
14.11.5 Checking the rim tape
NOTE
Damage to the inner tube due to damaged or poorly fitting rim
tape.
Risk of damage!
x Align the rim tape so that all the spoke nipples and spoke
holes are covered.
x Replace the rim tape if its fabric is torn or damaged.
On rims with a double base, known as hollow section rims, the rim tape must span the
entire base without being so wide that it protrudes at the edges of the rim.
x If you lack the necessary expertise and the tools required, have your dealer check
the rim tape and replace it if necessary.
x When you have removed the tyre, check the rim tape and replace it if necessary to
prevent damage to the inner tube.
14.11.6 Fitting clincher or folding tyres
When fitting a tyre, ensure that no foreign bodies such as dirt or sand get
inside and that you do not damage the inner tube.
To fit clincher or folding tyres, follow these steps:
1. Place one edge of the rim inside the tyre.
2. Press the sidewall of the tyre fully over the edge of the rim with your thumbs.
3. Insert the inner tube valve vertically through the valve hole in the rim so that it
points directly at the wheel axle.
4. Inflate the inner tube slightly so that it becomes round, and place it completely
inside the tyre.
5. Use your thumbs to press the tyre over the edge of the rim as far as it will go.
6. Push the inner tube inside the tyre with your index fingers so as not to trap the
inner tube between the tyre and the rim.
7. Work your way evenly around the circumference of the tyre from both sides.
8. Finish by giving the tyre a firm tug downwards to move the previously fitted section
down into the deep rim base.
CycleMaintenance
118
9. Check the position of the inner tube and press the tyre over the edge of the rim
(see “Illustr.: Fitting clincher or folding tyres (A)”).
x If this is not possible, use the blunt end of the tyre lever to move the tyre over
the edge of the rim (see “Illustr.: Fitting clincher or folding tyres (B)”).
10. Press the valve into the inside of the tyre.
11. Realign the valve if necessary.
x If this is not possible, detach part of the tyre sidewall and realign the inner tube.
12. Move the semi-inflated tyre back and forth several times in a sideways direction to
check that the inner tube is positioned in the tyre correctly with no pinching.
13. Inflate the inner tube to the desired tyre pressure. The maximum tyre pressure is
indicated on the sidewall of the tyre.
14. Check whether the tyre is correctly positioned using the witness line alongside the
rim sidewall. The witness line must be an even distance from the edge of the rim all
round the tyre (see “Illustr.: Fitting clincher or folding tyres (C)”).
Illustr.: Fitting clincher or folding tyres (example)
A B C
Cycle Maintenance
119
14.11.7 Fitting UST tyres
No separate inner tube is needed with UST (universal system tubeless) tyres.
The tyre and rim are connected in such a way that no air can escape.
UST tyres may only be used with a UST rim or a UST wheel.
Have UST tyres fitted by your dealer only. Do not fit UST tyres yourself
unless you have the necessary expertise.
x Only fit UST tyres by hand. Do not use a tyre lever.
x Remove dirt and lubricant before fitting. UST tyres must be free of dust and grease
inside and around the tyre bead.
x Moisten the tyre bead with soap or tyre fitting lubricant before fitting so as not to
damage the UST tyre.
1. Using your hands, press the UST tyre onto the rim from outside.
2. First lift one tyre bead completely over one rim flange, then the other.
3. Centre the UST tyre in the rim well.
4. Centre the valve between the tyre sidewalls.
5. Inflate the UST tyre to the maximum tyre pressure.
6. Check whether the UST tyre is correctly positioned using the fine witness line,
which must be an even distance from the rim all around the UST tyre.
x Use the valve to reduce the tyre pressure if necessary.
CycleMaintenance
120
14.11.8 Fitting the wheel
WARNING
Brake failure due to fitting the brake incorrectly.
Risk of accident and injury!
x With rim brakes, reattach the brake cable immediately.
x With hydraulic rim brakes, reattach the brake body
immediately and close the quick-release lever.
x Ensure that the brake body touches the rim and not the tyre
or the spokes.
To fit the wheels, reverse the sequence of steps for removing the wheels.
x With disc brakes, check that the brake pads are precisely positioned in the mounts
on the brake calliper before fitting the wheel.
x Ensure that you push the brake disc between the brake pads.
14.11.8.1 Fitting the front wheel
1. Thread the front wheel through the drop-out locks.
2. Fasten the nut on the quick release.
3. Close the quick-release lever.
4. Check whether the front wheel turns smoothly.
x If the front wheel does not turn smoothly, centre the wheel in the suspension fork.
14.11.8.2 Fitting the rear wheel
1. Pull the rear derailleur backwards by hand (see the “Maintenance / Removing the
wheel / Removing the rear wheel” chapter).
2. Place the chain on the smallest chainring and press the chain down.
3. Thread the rear wheel through the drop-out locks if necessary.
4. Push the rear wheel up into the drop-out locks.
5. Fasten the nut on the quick release.
6. Close the quick-release lever.
7. Check whether the rear wheel turns smoothly.
x If the rear wheel does not turn smoothly, centre the wheel between the chain stays.
Cycle Maintenance
121
If the cycle is equipped with a rear derailleur that features a chain adjuster lock:
x Use the lever on the top of the rear derailleur to activate the derailleur once you
have fitted the rear wheel.
14.11.8.3 After fitting the wheels
WARNING
Brake failure due to fitting the brake incorrectly.
Risk of accident and injury!
x Before the first ride after fitting a wheel, check whether there is
any grease or other lubricant residue left on the brake bodies
from the fitting process.
x Remove grease or other lubricant residue from the brake
bodies if necessary.
x Ensure that the brake bodies meet the braking surfaces.
x If applicable, remove the transport lock before fitting.
x Pull the brake lever – several times in the case of disc brakes – and turn the wheel.
x Ensure that the brake bodies do not grind against the braking surfaces.
CycleMaintenance
122
14.12 Brake system
WARNING
Brake failure due to incorrectly adjusted brakes.
Risk of accident and injury!
x Have brake adjustments carried out by your dealer only.
x Do not make any adjustments to the brakes if you lack the
necessary expertise or the tools required.
The following chapter will describe adjustments to a selection of brake systems.
Adjustment and operation may vary depending on the brake type and model.
x Note that a brake system is a complex system. Adjustments to individual parts of
the brake system affect each other.
x Have your dealer carry out adjustments.
x Refer to and follow information from the component manufacturer.
x Test the functionality of the brake system after making adjustments.
x Operate the brake and push the cycle in the direction of travel.
Check whether the associated wheel is braked.
x Lift the cycle and turn the wheel. Listen for grinding noises.
x Have the brakes checked if you hear grinding noises.
x If the brakes are not functional, the cycle must not be used.
x Have non-functional brakes repaired or replaced by your dealer.
Cycle Maintenance
123
14.12.1 Rim brakes in general
The following instructions apply to mechanical and hydraulic rim brakes.
14.12.1.1 Checking a brake pad
NOTE
Damage to the rim by the brake block holder due to worn brake
pads.
Risk of damage!
x Immediately replace the brake pad, or the brake block holder
if necessary, when pads are worn.
x Contact your dealer if you lack the necessary expertise and
the tools required to replace the brake pads, or the brake
block holders if necessary.
NOTE
Damage to tyres or spokes due to incorrectly adjusted brake
block holders.
Risk of damage!
x Adjust the brake block holder so that it is parallel to the rim.
The brake pads must be changed before the
wear indicator on the pad is reached.
Have your dealer replace the brake pads,
or brake block holders if necessary, and
readjust the brake system afterwards.
2
1
Illustr.: Brake block holder with a wear
indicator (example)
1 Brake pad
2 Wear indicator
CycleMaintenance
124
14.12.1.2 Changing a brake pad
WARNING
Reduced brake force due to uneven wear on the brake pads.
Risk of accident and injury!
x Always replace brake pads in pairs.
x Make identical adjustments to brake block holders that belong
together.
x If you lack the necessary expertise and the tools re
quired to
replace the brake block holders, contact your dealer.
Replacement may involve changing the
entire brake block holder or just the brake
pad, depending on the brake design.
x Only install brake pads that fit your rim.
Consult your dealer.
x If the entire brake block holder needs
to be changed, follow the relevant
instructions (see the “Maintenance
/ Brake system /Mechanical rim
brake”chapter or the“Maintenance /
Brake system /Hydraulic rim brake”
chapter).
Illustr.: Brake pad with a screw or pin (example)
1 Brake block holder and brake pad
2 Tyre
3 Rim
4 Distance between brake pad and tyre
5 Brake pad fastening pin
6 Brake pad fastening screw
4
21 3
56
Cycle Maintenance
125
14.12.1.3 Changing a screw-type brake pad
1. Loosen the brake pad fixing screw by turning it anticlockwise.
2. Pull the used brake pad out of the brake block holder counter to the direction of
travel.
3. If applicable, follow the specification on the new brake pads regarding the direction
of travel or note the screw recess.
4. Push the new brake pad into the brake block holder.
5. Tighten the brake pad fixing screw by turning it clockwise, observing the applicable
torque.
14.12.1.4 Changing a brake pad with a fixing pin
1. Pull the fixing pin out of the used brake pad.
2. Pull the used brake pad out of the brake block holder counter to the direction of
travel.
3. Note the recess for the fixing pin.
4. Push the new brake pad into the brake block holder.
5. Push the fixing pin fully into the brake pad.
14.12.1.5 Changing the brake block holders on a racing bike
In order to change the brake block holders, the quick-release lever on the brake must
generally be opened. The position of the quick-release lever may vary depending on the
brake design.
WARNING
Lack of brake functionality when the quick-release lever is open.
Risk of accident and injury!
x Only operate the quick-release lever when you are removing
wheels or changing brake block holders.
x Check the quick-release lever before every ride.
x Close the quick-release lever after maintenance work.
CycleMaintenance
126
1. Open the quick-release lever (see
“Illustr.: Preparing the brake”).
2. Remove the wheel (see the “
Maintenance /
Removing the wheel” chapter).
3. Loosen the brake block holder screw joint in an anticlockwise direction.
4. Remove the used brake block holders.
5. If applicable, follow the specification on the brake block holders regarding the
direction of travel and insert the new brake block holders.
6. Hand-tighten the brake block holder screw joint in a clockwise direction.
7. Align the brake block holders parallel to the rim so that the distance between the
upper edge of the brake block holder and the tyre is 2 mm/0.08" (see
“Illustr.: Brake block holder alignment”).
8. Close the quick-release lever.
9. Tighten the brake block holder screw joint, observing the applicable torque.
10. To adjust the distance between the brake block holders and the rim so that it is
identical on both sides, turn the centring screw.
11. Adjust the distance between the brake block holders and the rim to
1–2 mm/0.04–0.08" (see “Illustr.: Racing bike rim brake”).
1
Illustr.: Preparing the brake
1 Rim brake quick-release lever
Cycle Maintenance
127
14.12.1.6 Adjusting brake pad distance on a racing bike
The distance between the rim and brake pad is adjusted to 1–2 mm/0.04–0.08".
1. Turn the centring screw until the distance between the two brake pads is equal.
2. Loosen the lock nut by giving it one turn (see “Illustr.: Racing bike rim brake”).
3. Tighten or loosen the knurled screw until the distance between the brake pads and
the rim is 1–2 mm/0.04–0.08".
4. Tighten the lock nut.
Illustr.: Racing bike rim brake (example)
1 Knurled screw
2 Brake arm
3 Centring screw
4 Brake block holder and brake pad
5 Rim
6 Distance between the brake block holder and rim
7 Quick-release lever
8 Lock nut
6
1
4
3
8
2
5
7
5321 4
Illustr.: Brake block holder alignment (example)
1 Brake block holder
2 Brake block holder screw joint
3 Distance between the brake block holder and tyre
4 Tyre
5 Rim
CycleMaintenance
128
14.12.2 Mechanical rim brake
14.12.2.1 Changing a brake block holder
WARNING
Reduced brake force due to uneven wear on the brake pads.
Risk of accident and injury!
x Always replace brake pads in pairs.
x Make identical adjustments to brake block holders that
belong together.
x If you lack the necessary expertise and the tools required to
replace the brake block holders, contact your dealer.
The brake cable is generally fastened to the brake with a cylindrical cable nipple.
If the brake cable is screwed to the brake arms, contact your dealer.
2
1
5
4
3
6
1
2
5
4
3
6
Illustr.: Rim brake with a cable nipple (example)
1 Cable nipple
2 Brake arm
3 Tyre
4 Rim
5 Brake block holders
6 Spring preload adjustment screw
Illustr.: Rim brake with a cable guide (example)
1 Cable guide
2 Brake arm
3 Tyre
4 Rim
5 Brake block holders
6 Spring preload adjustment screw
Cycle Maintenance
129
Press both brake block holders against the rim and detach the brake cables.
x If this is not possible, loosen the brake cable tension lock nut and turn the
knurled screw clockwise until the brake arms can be squeezed together
enough to detach the brake cable.
1. Loosen the brake block holder screw joint in an anticlockwise direction
(see “Illustr.: Brake block holder alignment”).
2. Pull the brake arms apart and remove the used brake block holders.
If applicable, note the order of the spacing washers.
3. Clean the brake with a clean cloth.
4. If applicable, follow the specification on the brake block holders regarding the
direction of travel and follow the order of the spacing washers. Insert the new
brake block holders.
5. Hand-tighten the brake block holder
screw.
6. Press the brake arms against the rim
and align the brake block holders
parallel to the rim.
7. Move the brake block holders until the
distance between the upper edge of
the brake block holders and the tyre is
2 mm/0.08" (see “Illustr.: Brake block
holder alignment”).
8. Attach the brake cable.
x If this is not possible, loosen the
brake cable tension lock nut and
turn the knurled screw clockwise
until the brake arms can be
squeezed together enough to
attach the brake cable.
9. Fix the brake block holders in place by
operating the brake lever and tighten
the brake block holder screw joint,
observing the applicable torque.
5321 4
Illustr.: Brake block holder alignment (example)
1 Brake block holder
2 Brake block holder screw joint
3 Distance between the brake block holder
and tyre
4 Tyre
5 Rim
CycleMaintenance
130
14.12.2.2 Adjusting the brake block holder distance
The distance between the rim and brake pads is adjusted to 1–2 mm/0.04–0.08", and
must be equal on both sides. If the distances are different, the spring preload is adjusted.
If the distance from the rim to one of the two brake block holders is decreased, the
distance to the opposite brake block holder is increased.
x To increase the distance to a brake
block holder, turn the spring preload
screw clockwise.
x To decrease the distance to a brake
block holder, turn the spring preload
screw anticlockwise.
14.12.2.3 Checking the brake system
x Check the entire brake system for wear,
dirt and damage.
x Carry out a stationary functionality test.
14.12.3 Hydraulic rim brake
WARNING
Possible loss of eyesight on contact with brake fluid.
Risk of accident and injury!
x Wear protective gloves and safety goggles when carrying out
maintenance work on a hydraulic rim brake.
x If brake fluid gets in your eye, rinse it out with clean water
straight away.
x Contact a doctor immediately after contact with brake fluid.
Illustr.: Brake block holder distance (example)
1 Distance between the rim and brake pad
2 Rim
3 Brake block holders
4 Spring preload screw
1
2
3
4
Cycle Maintenance
131
CAUTION
Loss of force in the hydraulic brake system.
Risk of accident and injury!
x Have the brake fluid changed regularly by your dealer.
x Refer to and follow specifications from the manufacturer
regarding brake fluid changes.
NOTE
Damage to tyres or spokes due to incorrectly fitted brake pads.
Risk of damage!
x Align the brake pads parallel to the rim.
14.12.3.1 Changing the brake block holders
Replacement may involve changing the
entire brake block holder or just the brake
pad, depending on the brake design.
If only changing the brake pad, follow the
instructions in the “Maintenance / Brake
system / Rim brakes in general / Changing a
brake pad” chapter. The brake block holders
are generally fastened to the brake with a
clip-type mechanism.
1. Open the quick-release lever on the
brake.
2. Remove this side of the brake from the
brake mount on the front fork or frame.
3. Remove the wheel (see the “Wheels
and tyres” chapter).
1
Illustr.: Hydraulic rim brake (example)
1 Retaining bo
lts for the brake piston cl
amps
2 Quick-release lever
3 Brake block holder
2
3
CycleMaintenance
132
4. Pull the brake block holders out of the brake.
5. If applicable, note the direction of travel and insert the new brake block holders.
The brake block holders will engage with an audible click.
6. Fit the wheel.
7. Put the previously removed side of the brake back on the brake mount and loosen
the retaining bolts for the brake piston clamps.
8. Carefully operate the brake lever and align the brake block holders parallel to the
rim so that the distance between the upper edge of the brake pads and the tyre is
2 mm/0.08".
9. Close the quick-release lever on the brake.
10. Operate the brake lever several times until the usual pressure point is reached.
14.12.3.2 Adjusting brake block holder distances (Magura HS models)
The following describes how to adjust brake block holder distances, using the example
of a Magura HS.
The distance between the rim and brake
block holder is adjusted to 1–2 mm/
0.04–0.08".
1. Loosen the pressure point adjustment
screw on the brake lever by turning it
anticlockwise. Ensure that you do not
unscrew it completely.
2. Turn the brake boss screw
anticlockwise until the brake boss can
be moved.
3. Press the brake cylinders and brake
block holders against the rim.
4. Align the brake boss so that the brake
block holders are parallel to the rim and
the distance between the upper edge of
the brake pad and the tyre is 2 mm/
0.08".
5. Carefully operate the brake lever so that
the brake boss does not slip.
6. Slowly release the brake lever until the
distance between one brake block holder
and the rim is 1–2 mm/0.04–0.08"
(see “Illustr.: Hydraulic rim brake”).
Illustr.: Hydraulic rim brake (example)
1 Brake boss screw
2 Distance between the rim and brake block
holder
3 Brake block holders
4 Brake cylinders
3
2
4
1
Cycle Maintenance
133
7. Hold or fix the brake lever in this position.
8. Tighten the boss screw on the brake block holder by turning it clockwise,
observing the applicable torque.
9. Repeat steps 5–8 for the opposite brake pad.
10. Operate the brake lever several times until the usual pressure point is reached.
14.12.3.3 Checking the brake system
x Check the entire brake system for leaks, dirt and damage.
x Check the rims for dirt and wear.
x Carry out a stationary functionality test.
14.12.4 Disc brake
WARNING
Possible loss of eyesight on contact with brake fluid.
Risk of accident and injury!
x Wear protective gloves and safety goggles when carrying out
maintenance work on a hydraulic disc brake.
x If brake fluid gets in your eye, rinse it out with clean water
straight away.
x Contact a doctor immediately after contact with brake fluid.
CAUTION
Loss of force in the hydraulic brake system.
Risk of accident and injury!
x Have the brake fluid changed regularly by your dealer.
Disc brakes centre themselves automatically. Adjustments to disc brakes are generally
unnecessary. The brake must be readjusted or the brake disc trueness checked in case
of doubt if grinding noises are produced.
The maintenance work for mechanical and hydraulic disc brakes is largely identical.
x Refer to the notes in this chapter for details specific to hydraulic brakes.
x If you lack the necessary expertise and the tools required to adjust disc brakes,
CycleMaintenance
134
contact your dealer.
14.12.4.1 Bedding in a disc brake
The disc brake bedding-in process may be carried out in various ways depending on the
brake pad material.
x Refer to the information enclosed by the manufacturer about the brake pads.
14.12.4.2 Checking the brake disc
The minimum thickness of the brake disc is generally shown on the disc.
x Check the brake disc thickness with a measuring calliper.
x Check the brake disc for dirt.
x Check the brake disc trueness.
14.12.4.3 Adjusting the pressure point
x More information about adjusting the pressure point can be found in the “Brake /
Adjustments / Adjusting the pressure point” chapter.
14.12.4.4 Adjusting the brake calliper
1. Turn the brake calliper screws
anticlockwise until the brake calliper can
be moved.
2. Pull the brake lever for the brake that is
to be adjusted, and hold this position.
3. Turn the brake calliper screws clockwise
until the brake calliper can no longer be
moved.
4. Release the brake lever.
5. Tighten both brake calliper screws,
observing applicable torques.
21
Illustr.: Disc brake (example)
1 Brake calliper screw
2 Brake disc
Cycle Maintenance
135
14.12.4.5 Changing brake pads
NOTE
Uneven brake pad wear due to changing the brake pads
incorrectly.
Risk of damage!
x Always change brake pads in pairs.
x Use brake pads of the same type.
x Adjust the brakes after every change.
NOTE
Loss of brake fluid and damage to the brake due to operating the
brake lever when the brake pads or wheels are removed.
Risk of damage!
x Never operate the brake lever while the wheel, brake block
holders or brake pads are removed.
1. Remove the wheel (see the “Wheels and tyres / Fitting and removing the front/rear
wheel” chapter).
2. Remove the circlip from the screw and loosen it, or bend the ends of the pin
together and pull it out.
CycleMaintenance
136
3. Pull the brake pads out of the brake
calliper.
4. Clean the brake pistons with a clean
cloth.
5. Press both brake pistons into the brake
calliper simultaneously with a brake
piston spreader.
6. Remove the used brake pads from the
retaining bracket and clean the bracket
with a clean cloth.
7. If applicable, follow the specification on the new brake pads regarding the direction
of travel or whether they are for the left or right-hand side, and insert the new brake
pads in the brake calliper with the retaining bracket.
8. Push the brake pad screw or pin through the brake pad and holder eyes and into
the brake calliper.
9. Tighten the screw, observing the applicable torque, and secure it with the circlip or
bend the ends of the pin apart.
10. Fit the wheel.
2
1
1
2
3
Illustr.: Brake calliper with a screw (example)
1 Brake pad screw
2 Screw circlip
3 Brake pads
Illustr.: Brake calliper with a pin (example)
1 Pin
2 Brake pads
Illustr.: Disc brake pad (example)
Cycle Maintenance
137
14.12.4.6 Checking a brake pad
Brake pads must generally be removed in order to check them. The minimum brake pad
thickness may vary depending on the brake design.
x Minimum thickness specifications for the brake pads can be found in the
information enclosed by the manufacturer.
1. Remove the wheel (see the “Wheels and tyres / Fitting and removing the front/rear
wheel” chapter).
2. Remove the circlip from the screw and loosen it, or bend the ends of the pin
together and pull it out.
3. Pull the brake pads out of the brake calliper and remove them from the retaining
bracket.
4. Check the thickness of the brake pads with a measuring calliper.
x If the brake pad thickness does not meet the specified minimum thickness,
replace the brake pads as described in the previous chapter, “Changing brake
pads”.
14.12.4.7 Checking the brake system
x Check hydraulic brake systems for leaks, dirt and damage.
x Check mechanical brake systems for damage.
x Carry out a stationary functionality test.
14.12.5 Coaster brake
If it is necessary to back-pedal more than 1/6 of a full pedal revolution before the coaster
brake takes effect, then it must be readjusted by your dealer.
WARNING
No coaster brake action where the chain has dropped off the
chainring or the reaction arm is loose.
Risk of accident and injury!
x If the coaster brake has no effect, brake carefully using the
front brake lever.
x Check the chain tension regularly so that the chain cannot slip off the chainring
(see the “Maintenance / Chain tension” chapter).
CycleMaintenance
138
x Feel the reaction arm and check
whether the screw joint is tight against
the chain stays.
x If the reaction arm fixing screw is loose,
tighten it in a clockwise direction.
x If you lack the necessary expertise and
the tools required to fasten the reaction
arm, have the coaster brake checked
and adjusted by your dealer.
14.13 Crankset
1. Try to move the pedal inwards or
outwards from side to side.
x Observe whether the crank,
bottom bracket or pedal bearing
can be moved sideways (see
“Illustr.:Crankset using the example
of a derailleur shifting system”).
2. Try to move the pedal vertically upwards
or downwards.
x Observe whether the crank or
pedal move vertically in the bottom
bracket or pedal bearing.
x If the pedal, crank or bottom bracket
can be moved sideways or vertically,
have the crankset checked by your
dealer.
1 2
Illustr.: Coaster brake (example)
1 Chain stays
2 Fastening clamp on the frame
3 Screw joint
4 Coaster brake reaction arm
3 4
Illustr.: Crankset using the example of a
derailleur shifting system (example)
1 Chainring
2 Crank
3 Pedal
2
3
1
Cycle Maintenance
139
14.14 Lighting set
1. Check whether the cable connections to the headlamp, rear lamp and dynamo
(if applicable) are firmly in place and look for damage and corrosion.
x If the cable connections are damaged, corroded or loose, have the lighting
repaired by your dealer.
2. Switch on the lighting and check whether the headlamp and rear lamp are lit.
With cycles that have a hub dynamo, turn the front wheel to do this.
3. Check the headlamp adjustment (see the “Basic adjustments / Lighting /
Headlamp” chapter).
x If you find damage to the lighting set, have it repaired by your dealer.
14.15 Hub dynamo
x Check the cable connections to the hub dynamo.
x Clean the connectors if necessary.
x Check whether the connectors are tight and look for corrosion.
x Reconnect if necessary.
x If the cable connections are damaged, have them replaced by your dealer.
14.16 Chain tension
This chapter applies to models with a coaster brake or hub shifting system.
1. Set the cycle on the kickstand.
2. Press the chain upwards or downwards
and check whether you can press it
through a distance of between 10 and
15 mm/0.4–0.6" (see “Illustr.: Chain
tension”).
x If you can press the chain upwards
or downwards by less than 10 mm/
0.4" or more than 15 mm/0.6", or if
the chain is grinding against the all-
round chain guard, have the chain
tension adjusted by your dealer.
Illustr.: Chain tension (example)
10-15 mm/0.4–0.6"
CycleMaintenance
140
14.16.1 Chain tension in derailleur shifting systems
On cycles with a derailleur shifting system, the chain is tensioned by the chain adjuster
on the gear shifting system’s rear derailleur.
1. Set the cycle on the kickstand or fix the
cycle in place with a suitable work stand
and check whether the chain is
sagging.
2. Gently press the chain adjuster forwards
and check whether it moves back by
itself (see “Illustr.: Chain adjuster on the
rear wheel”).
x If the chain is sagging or the chain
adjuster does not move back by itself,
have the chain adjuster repaired by your
dealer.
14.16.2 Shift cables
1. Check that the outer casings and inner wires are undamaged.
2. Operate the gear shifting system and check whether the shift cables move freely.
x Have faulty shift cables replaced by your dealer.
14.16.3 Derailleur shifting system
1. Using a suitable work stand, hang the cycle up by its frame or the seat post.
2. Turn the crankset in the direction of travel.
3. Shift through all the sprockets and chainrings (see the “Derailleur shifting system”
chapter).
4. Check that all the gears shift correctly and whether any unusual noises are
produced in the process.
x If the gears do not shift correctly or if you hear unusual noises when shifting
gear, contact your dealer.
5. Oil the gear shifting system (see the “Cleaning / Gear shifting system” chapter).
Illustr.: Chain adjuster on the rear wheel
(example)
Cycle Maintenance
141
14.17 Tyre pressure recommendations
The figures in the following table are recommendations for the tyre pressure
at different tyre widths. Follow the tyre pressure specifications shown on
the tyre. Use a pump with a pressure display to inflate the tyres.
Tyre width
Recommended tyre pressure
bar psi
20 mm/0.78" 9.0 bar 130 psi
23 mm/0.91" 8.0 bar 115 psi
24 mm/0.94" 7.0 bar 100 psi
28 mm/1.1" 6.0 bar 85 psi
30 mm/1.18" 5.5 bar 80 psi
32 mm/1.26" 5.0 bar 70 psi
35 mm/1.38" 4.5 bar 65 psi
37 mm/1.46" 4.5 bar 65 psi
40 mm/1.57" 4.0 bar 55 psi
42 mm/1.65" 4.0 bar 55 psi
44 mm/1.73" 3.5 bar 50 psi
47 mm/1.85" 3.5 bar 50 psi
50 mm/1.97" 3.0 bar 45 psi
54 mm/2.13" 2.5 bar 35 psi
57 mm/2.24" 2.2 bar 32 psi
60 mm/2.36" 2.0 bar 30 psi
75 mm/2.95" 1.5 bar 22 psi
100 mm/3.94" 0.8 bar 12 psi
CycleMaintenance
142
14.18 Greasing and oiling
Component Interval
Care product
Chain
After cleaning or riding in the rain,
every 250 km/150 mi
Chain oil
Brake and shift cables When functioning poorly, 1× per year Silicon-free grease
Wheel bearing, pedal bearing,
bottom bracket
1× per year Bearing grease
Suspension elements
After cleaning or riding in the
rain, according to manufacturer
specifications
Dedicated spray
grease
Contact surfaces of carbon
components
On fitting
Fitting lubricant for
carbon components
Sliding surfaces of quick releases 1× per year Grease, spray oil
Metal seat posts in metal frames On fitting Grease
Shift system joints When functioning poorly, 1× per year Spray oil
Brake joints When functioning poorly, 1× per year Spray oil
Joints in full-suspension frames When functioning poorly, when dirty
According to
manufacturer
specifications
14.19 Cleaning and maintenance schedule
The cycle must be maintained at regular intervals. The details specified in the table are
guidelines for riders who cover between 1,000 and 2,000 km/600 and 1,200 mi or between
50and100hours of operation per year.
Component Task
Before
every
ride
Monthly Annually
Other
interval
Lighting Test functionality x
Tyres
Check tyre pressure x
Check tread depth and
sidewalls
x
Rim brakes
Check lever travel, pad
thickness and position
relative to the rim; stationary
brake test
x
Brake pads in
rim brakes
Clean x
Cycle Maintenance
143
Component Task
Before
every
ride
Monthly Annually
Other
interval
Brake cables/
pads/lines
Visual check x
Disc brakes
Lever travel, pad thickness,
leak-tightness,
Stationary brake test
x
Change brake fluid
(if DOT fluid)
x
1
Suspension fork
Check screws and tighten if
necessary
x
1
Change oil, grease
elastomers
x
1
Rigid fork
Check and replace if
necessary
x
1
at least
every
2years
Rims if using rim
brakes
Check wall thickness,
replace if necessary
x
1
no later
than after
the 2nd set
of brake
pads
Suspension
seat post
Maintain x
1
Bottom bracket
Check bearing play x
Remove and re-grease x
1
Chain
Check and oil if necessary x
Check for wear, change if
necessary, check derailleur
shifting system
x
1
from
1,000 km/
600 mi or
50 hours of
operation
Crank Check or tighten x
Paint/anodised
aluminium/
carbon
Preserve
x
1
at least
twice a year
Wheels
Check trueness and tension x
Centre or re-tension
x
1
as
needed
CycleMaintenance
144
Component Task
Before
every
ride
Monthly Annually
Other
interval
Aluminium
handlebars and
handlebar stem
Check and replace if
necessary
x
1
check at
least every
2years and
replace after
5years
Carbon
handlebars
Check and replace if
necessary
x
1
check at
least every
2years
Headset
Check bearing play x
Grease x
1
Metallic
surfaces
Preserve (except: rim
sidewalls with rim brakes,
brake discs)
x
1
at least
twice a year
Hubs
Check bearing play x
Grease x
1
Pedals Check bearing play x
Clipless pedals
Clean/grease lock
mechanism
x
Seat post/
handlebar stem
Check screws x
Remove and re-grease
Carbon: new fitting lubricant
x
1
Front/rear
derailleurs
Clean/oil x
Quick releases Check position x
Screws and
nuts
Check and tighten if
necessary
x
Valves Check position x
Shift/brake
cables
Remove and grease x
1
1
Have this work carried out by your dealer only.
Cycle Storage
145
15 Storage
If the cycle will not be used for a prolonged period, the following points must be noted
with regard to storage:
x Clean the cycle (see the “Cleaning” chapter).
x Store the
cycle
in a dry, frost-free place where it is protected against major
fluctuations in temperature.
x To prevent tyre deformation, store the cycle hanging by its frame.
x On a cycle with a derailleur shifting system, shift to the small chainring at the front
and the smallest sprocket at the back to take as much strain as possible off the
cables.
After storage, shift the chainring and cassette back to a gear combination
designed for riding before using the cycle again (see the “Derailleur shifting
system / Basics / Gear combinations” chapter).
16 Warranty
Over and above the statutory guarantee, Winora-Staiger GmbH/Haibike USA also
provides a warranty for the cycle frame. The warranty periods are as follows for models
from 2017 onwards, starting on the date of purchase by the original buyer
for aluminium frames: 5 years
for carbon frames: 5 years
for full-suspension frames (excluding bearings and dampers): 5 years
The warranty only applies to the original purchase of the cycle. Proof of purchase,
together with the completed cycle passport and handover certificate, must be submitted
when making a warranty claim.
The warranty only covers frame damage relating to quality, durability and freedom
from defects. Shipping and return costs for the defective frame, labour costs involved
in replacing a defective frame for a new one, and consequential costs resulting from a
defective frame are not covered by the warranty.
The warranty likewise excludes all damage resulting from insufficient care and
maintenance, excessive wear, accidents, cycle overloading, components fitted
incorrectly, and cycle alterations through the attachment and modification of additional
components. The warranty also does not apply if the cycle is used for improper sports
activities, such as performing jumps for which the cycle category was not intended, in
the event of any other type of overuse, and in cases where recommendations contained
in our original operating manual or made by our dealer are disregarded. Please refer to
the original operating manual for full details regarding proper handling of the frame.
CycleGuarantee
146
This warranty does not affect any further claims which you may be entitled to make
against the dealer under the statutory guarantee, such as your right to a discount, return
or compensation. The warranty and guarantee rights coexist. This warranty will expire
and not restart in the event that a frame is replaced under warranty.
When purchasing your cycle, you entered into a contract with your dealer. Claims under
this warranty or any other problems must be addressed exclusively to the dealer from
whom you purchased your cycle. To ensure these are handled smoothly, full proof of
purchase and cycle documents must always be submitted. The dealer will then contact
us for further action if necessary.
Should you authorise another dealer to submit a claim, further costs may be incurred as
a result. These costs are your own responsibility and will not be covered by us.
Winora-Staiger GmbH/Haibike USA reserves the right to charge a handling fee for
unjustified complaints.
17 Guarantee
Acquaint yourself with the national and regional guarantee regulations in your country.
The signed handover certificate and proof of purchase must be submitted in the event of
any guarantee claim. Keep hold of these documents.
The guarantee does not apply to damage caused by improper use, force majeure,
operational wear (see the “Safety / Notes on wear” chapter) or accidents.
Special guarantee provisions for pedelec/S-pedelec drives can be found in the
corresponding system manuals.
Cycle Disposal
147
18 Disposal
18.1 Cycle
Do not dispose of your cycle in household waste. Take it to a municipal collection point
or a recycling centre.
Alternatively, there are also collections organised by local councils and private
organisations. Contact your local council about this or refer to postal information.
18.2 Electronic components and accessories
Replaced or defective LED headlamps, LED rear lamps or hub dynamos, as well as
accessories such as bike computers or navigation devices, must also be disposed of
separately.
Take parts and devices of this kind to a municipal collection point or a recycling centre.
18.3 Packaging
The packaging used to protect your cycle during shipping, called transport packaging,
can generally be left with your dealer. All other types of packaging must be sorted and
disposed of separately. Dispose of cardboard along with waste paper and film in your
recycling collection, or ask your dealer about disposal.
18.4 Tyres and inner tubes
Tyres and inner tubes must not be disposed of in household waste.
Ask your dealer whether they take care of collection and disposal, or take these items to
a recycling centre or municipal collection point.
18.5 Lubricants and care products
Do not dispose of lubricants and care products in household waste, into the sewer system
or into the environment. They must be taken to a hazardous waste collection point.
Also follow the notes included on the packaging of such products.
Winora Group
Supplementary
User manual
Pedelec
S-pedelec
Pedelec/S-pedelec
1 Seat tube 16 Rechargeable battery
2 Top tube 17 Motor
3 Control unit 18 Pedal
4 Handlebar stem 19 Crank
5 Handlebars 20 Chainrings
6 Brake lever 21 Chain
7 Front fork/suspension fork 22 Chain stays
8 Headlamp 23 Rear derailleur
9 Spoke 24 Sprocket cassette
10 Wheel hub 25 Seat stays
11 Rim 26 Rear lamp
12 Ty re 27 Seat post clamp
13 Brake 28 Saddle clamp
14 Valve 29 Saddle
15 Down tube
Example illustration
L
6
0
-
5
8
4
2
3
-
5
0
p
s
i
1
6
0
-
3
5
0
k
P
a
1
,
6
-
3
,
5
B
a
r
1
2
5
3
6
10
9
8
7
13
11
16
15
14
17
26
25
29
23
22
21
20
24
28
27
12
18
19
4
Pedelec/S-pedelec
Contents
1 Basics � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
1�1 Reading and storing the user manual � � � � � � � � � � � � � � � � � � 1
1�2 Identification of warnings � � � � � � � � � � � � � � � � � � � � � � � � 1
1�3 Proper use � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
1�4 Product symbols � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
1�5 Notes on screw turning directions � � � � � � � � � � � � � � � � � � � 4
1�6 Pedelec and S-pedelec differences � � � � � � � � � � � � � � � � � � � 4
1�6�1 Pedelec� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
1�6�2 S-pedelec � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
1�7 Differences between a pedelec/S-pedelec and bike� � � � � � � � � � � � �6
1�8 EC certificate of conformity for S-pedelecs� � � � � � � � � � � � � � � 6
1�9 CE marking and declaration of conformity for pedelecs � � � � � � � � 7
1�10 Function� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
1�11 Range � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
1�12 Road use � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
1�13 Minimum tread depth� � � � � � � � � � � � � � � � � � � � � � � � � � 10
1�14 Minimum pull-out height � � � � � � � � � � � � � � � � � � � � � � � � 10
1�15 Insurance � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
1�16 Exclusion of consumable parts � � � � � � � � � � � � � � � � � � � � 10
1�17 Liability disclaimer � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
1�18 Transportation of children and cargo � � � � � � � � � � � � � � � � � 11
1�19 Luggage� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11
1�20 Transportation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 11
1�20�1 Pedelec/S-pedelec � � � � � � � � � � � � � � � � � � � � � � � � � � � � �11
1�20�1�1 By car � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �12
1�20�1�2 By other means � � � � � � � � � � � � � � � � � � � � � � � � � � � �12
1�20�2 Transporting or shipping the rechargeable battery � � � � � � � � � � � �12
2 Safety notes� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13
2�1 Usage safety notes� � � � � � � � � � � � � � � � � � � � � � � � � � � � 13
2�2 Road safety notes � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14
2�3 Charger safety notes� � � � � � � � � � � � � � � � � � � � � � � � � � � 15
Pedelec/S-pedelec
2�4 Rechargeable battery safety notes � � � � � � � � � � � � � � � � � � � 17
2�5 Residual risks � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 19
2�6 General safety precautions � � � � � � � � � � � � � � � � � � � � � � � 19
2�6�1 In case of excessive heat � � � � � � � � � � � � � � � � � � � � � � � � � �20
2�6�2 In case of deformation, odour or fluid� � � � � � � � � � � � � � � � � � � �20
3 Basic adjustments� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20
3�1 Preparations � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20
3�1�1 Pedelec/S-pedelec adjustments to suit the rider� � � � � � � � � � � � � �20
3�1�2 Notes on the key � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �20
3�1�3 Charger� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �21
3�1�4 Rechargeable battery � � � � � � � � � � � � � � � � � � � � � � � � � � � �21
3�2 Before every ride � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21
3�3 Before the first ride� � � � � � � � � � � � � � � � � � � � � � � � � � � � 21
3�4 First ride � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22
3�5 Inspection instructions� � � � � � � � � � � � � � � � � � � � � � � � � � 22
4 Operation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 23
4�1 Pedelec/S-pedelec� � � � � � � � � � � � � � � � � � � � � � � � � � � � 23
4�1�1 Switching the drive on/off � � � � � � � � � � � � � � � � � � � � � � � � � �23
4�1�2 Switching the lighting on/off� � � � � � � � � � � � � � � � � � � � � � � � �23
4�2 Drive overheating protection � � � � � � � � � � � � � � � � � � � � � � 24
4�3 Control unit � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 24
4�3�1 Pedelec pushing aid � � � � � � � � � � � � � � � � � � � � � � � � � � � � �25
4�3�2 S-pedelec starting aid � � � � � � � � � � � � � � � � � � � � � � � � � � � �25
4�4 Rechargeable battery � � � � � � � � � � � � � � � � � � � � � � � � � � 25
4�4�1 Safety feature � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �26
4�4�2 Rechargeable battery and charger applications � � � � � � � � � � � � � �27
4�4�3 Riding with an empty battery � � � � � � � � � � � � � � � � � � � � � � � �27
4�4�4 Removing/inserting the rechargeable battery � � � � � � � � � � � � � � �27
4�4�5 Charging the battery � � � � � � � � � � � � � � � � � � � � � � � � � � � � �28
4�4�6 Connecting the rechargeable battery to the charger � � � � � � � � � � � �28
4�4�7 Stopping the charging process � � � � � � � � � � � � � � � � � � � � � � �29
4�4�8 Charging times � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �29
Pedelec/S-pedelec
5 Cleaning and maintenance � � � � � � � � � � � � � � � � � � � � � � � � � � � � 29
5�1 Checking the electric drive system � � � � � � � � � � � � � � � � � � � 30
5�2 Troubleshooting � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 30
6 Storage � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 32
6�1 Storing the rechargeable battery � � � � � � � � � � � � � � � � � � � � 32
6�2 Storing the pedelec/S-pedelec � � � � � � � � � � � � � � � � � � � � � 33
7 Disposal � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 33
7�1 Cycle � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 33
7�2 Electrical elements, single-use batteries and rechargeable batteries � � 33
7�3 Electronic components and accessories � � � � � � � � � � � � � � � � 34
7�4 Packaging � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 34
7�5 Tyres and inner tubes � � � � � � � � � � � � � � � � � � � � � � � � � � 34
7�6 Lubricants and care products � � � � � � � � � � � � � � � � � � � � � � 34
Pedelec/S-pedelec Basics
1
1 Basics
1.1 Reading and storing the user manual
Contrary to the official standard, EPACs (electric power-assisted cycles)
and S-EPACs (speed electric power-assisted cycles) are referred to below
as pedelecs (from “pedal electric cycle”) and S-pedelecs (from “speed
pedal electric cycle”) as these terms are in common use.
This user manual is a supplement. It assumes that you have read the
“Cycle” user manual. Read all the warnings and notes in this user manual
carefully before putting the pedelec or S-pedelec into operation.
This user manual is an integral part of the pedelec or S-pedelec.
Store this user manual carefully so that it is available at all times. If passing the
pedelec or S-pedelec on to a third party, include the user manual along with it.
Also refer to and follow the manuals enclosed with the pedelec/S-pedelec
drive system.
1.2 Identification of warnings
The following signal symbols and signal words are used in this user manual to warn
against personal injury or damage to property.
Warnings are intended to draw attention to possible dangers. Failure to follow a warning
may result in injury to yourself or other people, as well as causing property damage.
Read and follow all warnings.
DANGER
This warning identifies a hazard with a high degree of risk, resulting in serious
injury or death if not avoided.
WARNING
This warning identifies a hazard with a moderate degree of risk, resulting in
serious injury if not avoided.
CAUTION
This warning identifies a hazard with a low degree of risk, resulting in minor or
moderate injury if not avoided.
Pedelec/S-pedelecBasics
2
NOTE
This warning calls attention to potential property damage.
1.3 Proper use
This user manual is a supplement, and assumes that you have read the “Cycle” user
manual.
Proper use also includes following what is specified in the “Cycle” user manual.
The use of child seats and trailers of any kind with S-pedelecs is prohibited by
Winora-Staiger GmbH/Haibike USA.
Neither the manufacturer nor the dealer accept any liability for damage caused due to
improper use.
Please also refer to the “Cycle category” chapter.
Pedelec/S-pedelec Basics
3
1.4 Product symbols
The following symbols are shown on packaging, the rechargeable battery or the charger.
Symbol Description
Marking for electrical devices that must not be disposed of in household or
non-recyclable waste. Dispose of electrical devices with this marking at suitable
collection points for environmentally friendly recycling.
Marking for single-use and rechargeable batteries that must not be disposed of
in household or non-recyclable waste. Dispose of single-use and rechargeable
batteries with this marking at suitable collection points for environmentally friendly
recycling.
Marking for materials that are hazardous to the environment. Take particular care
when handing products with this marking. Observe disposal regulations!
Marking for recyclable materials. Sort packaging and dispose of separately.
Dispose of cardboard along with waste paper and film in your recycling collection.
Marking for products that must only be used indoors.
Europe: The 230 V~/50 Hz mains power supply has a class II protection rating.
USA: The 120 V~/60 Hz mains power supply has a class II protection rating.
Symbol for direct current (DC).
Symbol for alternating current (AC)
The following symbol is only applicable for Europe:
Symbol Description
Products marked with this symbol meet all applicable European Economic
Community regulations.
Pedelec/S-pedelecBasics
4
1.5 Notes on screw turning directions
NOTE
Material damage due to handling screw joints incorrectly.
Risk of damage!
x Observe the turning direction of screws, thru-axles and nuts.
x Tighten screws, thru-axles and nuts by turning them clockwise.
x Loosen screws, thru-axles and nuts by turning them anticlockwise.
In the event of any deviation from this rule, the change in turning direction
will be indicated in the respective chapter. Refer to the relevant notes.
1.6 Pedelec and S-pedelec differences
1.6.1 Pedelec
The following paragraph is only applicable for Europe:
Pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 25 km/h when you pedal.
Depending on the cycle model, there may be a pushing aid which can accelerate the
cycle up to 6 km/h depending on what gear the shifting system is in.
The following paragraph is only applicable for the USA:
Pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 20 mph when you pedal. By law, pedelecs are class 1 (see the “Explanation
of symbols” chapter). There may be a pushing aid depending on the cycle model.
How this functions is described in more detail in the drive system user manual enclosed
with the cycle.
Pedelecs are cycles that are legally classed as bikes in most countries. Acquaint yourself
with the national and regional regulations and classification in your country.
x Find out what category your pedelec falls into in your country. Note that regulations
vary from country to country.
x Acquaint yourself with the applicable national and regional road regulations.
x Continually acquaint yourself with changes in the content of applicable regulations.
x Note that tampering with the pedelec speed can not only have legal
consequences, but may also lead to accidents.
Pedelec/S-pedelec Basics
5
1.6.2 S-pedelec
The following paragraph is only applicable for Europe:
S-pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 45 km/h when you pedal. Depending on the model, all-electric operation
up to a maximum of 18 km/h may also be possible.
The following paragraph is only applicable for the USA:
S-pedelecs are cycles with an electric auxiliary motor that provides assistance up to a
maximum of 28 mph when you pedal. There may be a pushing aid depending on the
cycle model. How this functions is described in more detail in the drive system user
manual enclosed with the cycle. By law, S-pedelecs are class 3 (see the “Explanation of
symbols” chapter).
In some countries, S-pedelecs are classed as motor vehicles. Acquaint yourself with the
national and regional regulations and classification in your country.
Note national and regional differences with regard to:
Minimum age limits for using S-pedelecs
Driving licenses
Compulsory insurance and registration if applicable
Operating licenses
Compulsory helmet use
Provisions regarding use on bike paths, woodland trails and forest roads
x Note that tampering with the S-pedelec speed can not only have legal
consequences, but may also lead to accidents.
Pedelec/S-pedelecBasics
6
1.7 Differences between a pedelec/S-pedelec and bike
CAUTION
Unexpected pedelec/S-pedelec behaviour due to sharp
acceleration.
Risk of accident and injury!
x Frost, rain, sand or leaves on the road can lead to accidents,
particularly with pedelecs/S-pedelecs that have front-wheel drive.
x Use the cycle’s gear shifting system and always ride in a low gear.
The components of the electric drive are the main differences between a conventional
bike and a pedelec/S-pedelec.
Due to the significantly higher weight and change in weight distribution, a pedelec/
S-pedelec handles differently.
The drive has a significant impact on braking behaviour.
Pedelecs/S-pedelecs require more braking force. This can increase wear.
On pedelecs/S-pedelecs with a central motor, there are significantly higher forces
acting on the drive train. This increases wear.
Electrical assistance may increase riding speed. Careful riding is required as other
road users may need to adjust to the higher speed of the pedelec/S-pedelec.
The handling and braking behaviour requires appropriate expertise, as does use of
the rechargeable battery and charger.
x Familiarise yourself with the characteristics of the pedelec/S-pedelec even if
you already have experience with electrically assisted cycles (see the “Basic
adjustments / Before the first ride” chapter).
1.8 EC certificate of conformity for S-pedelecs
The following section is only applicable for Europe:
CoC = certificate of conformity
This document is enclosed with your S-pedelec and uniquely assigned to this one cycle.
The CoC confirms that the cycle corresponds to the approved type. You need the CoC
to insure the cycle, and to register it if applicable. Acquaint yourself with national and
regional regulations before your first ride.
Pedelec/S-pedelec Basics
7
Please note:
Keep the CoC in a safe place as you need it to insure the cycle. The CoC will also
be required by the buyer in the event that you sell the cycle. There is great effort and
significant cost involved in producing a duplicate CoC at a later date.
Non-EU countries:
In countries outside the European Union, the EC certificate of conformity supplied
may not be sufficient. In Switzerland, for example, separate type approval and a cycle
registration document are required.
1.9 CE marking and declaration of conformity for pedelecs
The following paragraph is only applicable for Europe:
With the CE marking on the pedelec and the declaration of conformity, the manufacturer
of your pedelec confirms that the product meets all requirements and other relevant
provisions in directives 2006/42/EC, 2014/30/EC and standards ISO 4210 and
DINEN15194, as well as other relevant directives and standards if applicable.
The declaration of conformity can be found in the quick-start guide for the drive system.
1.10 Function
The drive only assists with riding when you are also pedalling. The amount of assistance
is adjusted automatically according to the selected gear, depending on the system or
model installed, pedal force, load and speed:
Depending on the design of your pedelec, the drive may assist up to a speed
of 25km/h (only applicable for the USA: 20 mph). The pushing aid can
accelerate the cycle up to 6 km/h (USA: There may be a pushing aid depending
on the cycle model� How this functions is described in more detail in the
drive system user manual enclosed with the cycle�) depending on what gear
the shifting system is in.
Depending on the design of your S-pedelec, the drive may assist up to a speed
of 45 km/h (only applicable for the USA: 28 mph). The starting aid can
accelerate the cycle up to 18 km/h ((USA: There may be a starting aid
depending on the cycle model� How this functions is described in more detail
in the drive system user manual enclosed with the cycle�) depending on what
gear the shifting system is in.
In terms of the maximum speed with pedal assistance, a tolerance of 10 % is permitted
and possible when riding.
Pedelec/S-pedelecBasics
8
1.11 Range
The drive is an auxiliary motor. To obtain the longest possible range, the following points
must be noted:
The motor works most efficiently at a cadence of 50–80 crank revolutions/minute.
x Shift to a lower or higher gear before inclines and descents to avoid excessively
fast or slow cadences.
x Operate the gear shifting system as if you were riding without assistance.
x Use the smaller gears in your gear shifting system on inclines, in headwinds and
with heavy loads.
Starting in the lowest gear increases the range.
x Always ride in a low gear and pedal as hard as possible.
x On models with hub shifting systems, you can shift into 1st gear while
stationary. On models with derailleur shifting systems, you should shift into the
lowest gear while you are still stopped.
Riding uphill reduces the range, as does frequent stopping and starting.
x Shift down to a lower gear in good time before inclines.
x Look ahead and anticipate while riding so that you can avoid unnecessary stops.
Riding on unsurfaced ground reduces the range.
x Where possible, ride on surfaced roads and paths.
A high gross weight (cycle + rider + luggage) increases energy consumption.
x Do not transport unnecessary loads.
You can get the most kilometres out of a new and fully charged battery.
Neglected cleaning and maintenance can reduce the range.
x Take care of the pedelec/S-pedelec on a regular basis and check the tyre pressure
regularly.
x Continually test the functionality of the pedelec/S-pedelec and check for wear, as
well as referring to all notes on the rechargeable battery in this user manual and in
the drive system manual.
x Observe maintenance intervals.
High average speeds reduce the range.
The stronger the assistance mode, the shorter the range.
Ambient temperatures below +10 °C and above +40 °C /below 50 °F and above
104 °F can reduce the range.
Particularly high and particularly low ambient temperatures can permanently speed
up battery wear or even damage the rechargeable battery.
Pedelec/S-pedelec Basics
9
x Store the rechargeable battery at room temperature before a ride to ensure an
optimum temperature for use.
x Refer to the notes on storing the rechargeable battery correctly.
x Do not insert the rechargeable battery in the holder until just before the ride.
Because the range is dependent on a variety of factors such as the level of assistance,
speed, shifting behaviour, tyres and tyre pressure, age and condition of the rechargeable
battery, route profile and conditions, headwind and ambient temperature as well as the
weight of the cycle, rider and luggage, it is not possible to accurately predict the range
before setting off or during a ride.
In general, however:
If the level of assistance remains the same, then the less force you need to apply to
reach a particular speed (e.g. through optimum shifting behaviour), the less energy
the drive will consume and the longer the range from the battery charge.
If all other conditions are the same, then the higher the selected level of assistance,
the shorter the range.
1.12 Road use
The following paragraph is only applicable for Europe:
Depending on the design, pedelec assistance may be effective up to a speed of
25km/h. With an S-pedelec, the assistance is switched off at a speed of 45km/h.
The following paragraph is only applicable for the USA:
Depending on the design, pedelec assistance may be effective up to a speed of20 mph.
With an S-pedelec, the assistance is switched off at a speed of 28mph.
x Find out before your first ride whether your pedelec/S-pedelec is equipped in
accordance with requirements for use on the road. Note that national and regional
regulations may vary. For example:
Brakes
Lighting and reflectors
Bell or other approved warning device
Child trailers and child seats
x Acquaint yourself with the applicable national and regional road regulations.
For example:
Minimum rider age
Compulsory insurance
Operating licenses
Compulsory helmet use
Pedelec/S-pedelecBasics
10
Compulsory use of reflective safety vests
x Refer to and follow the traffic code.
x Bear in mind that tampering with the pedelec/S-pedelec speed, or tuning the
pedelec/S-pedelec, can have legal consequences.
Laws and regulations can change at any time, so acquaint yourself with
national and regional regulations on a regular basis.
1.13 Minimum tread depth
The following paragraph is only applicable for Europe:
Please note that a minimum tread depth of 1 mm is prescribed for cycles such as
S-pedelecs.
1.14 Minimum pull-out height
Depending on the S-pedelec model, the seat post may be labelled with a minimum pull-out
depth marking.
x Pull the seat post out far enough that the lighting components are not obscured by
any license plate which may be fitted to the saddle.
1.15 Insurance
x Check whether damage is adequately covered by the terms of your insurance.
x If in doubt, contact your insurance company.
1.16 Exclusion of consumable parts
In addition to the consumables listed in the “Cycle” user manual, the rechargeable
battery is also a consumable part. This does not include manufacturing defects.
The exact guarantee terms for drive system components can be found in their respective
system operating manuals, which are enclosed with your pedelec/S-pedelec.
You can also find them online at: www.winora-group.de/manuals.
1.17 Liability disclaimer
The manufacturer is not liable for damage or failures caused due to any direct or indirect
use of the pedelec/S-pedelec which falls outside what is deemed proper use.
Pedelec/S-pedelec Basics
11
1.18 Transportation of children and cargo
Winora-Staiger GmbH/Haibike USA does not permit the use of S-pedelecs to transport
children or cargo in a trailer.
Winora-Staiger GmbH/Haibike USA does not allow the option of using S-pedelecs to
transport a child in a child seat.
Winora-Staiger GmbH/Haibike USA accepts no liability for any damage resulting from
the use of trailers and/or child seats with S-pedelecs.
As to using a trailer of any design and/or a child seat with a pedelec, see the
“Safety / Notes on carrying children” chapter in the general cycle manual.
1.19 Luggage
Position your luggage on the S-pedelec so as not to obscure any license plate which
may be fitted to the saddle.
1.20 Transportation
1.20.1 Pedelec/S-pedelec
CAUTION
Damage to the rechargeable battery due to impacts.
Risk of short circuit and fire!
x Remove the rechargeable battery before transporting the
pedelec/S-pedelec.
x Transport the rechargeable battery with particular care.
The rechargeable battery must be removed from the pedelec/S-pedelec before
transportation (see the “Operation / Rechargeable battery / Removing/inserting the
rechargeable battery” chapter). Afterwards, cover the contacts of the rechargeable
battery to protect it against a short circuit. If the control unit is detachable, it should be
removed before transportation to prevent damage and loss.
x Acquaint yourself with national and regional regulations about transporting and
shipping rechargeable batteries.
x Refer to and follow the enclosed system manuals.
Pedelec/S-pedelecBasics
12
1.20.1.1 By car
x Stow the rechargeable battery so that it cannot slip or collide with other items
during the journey.
x Protect the rechargeable battery against compressive stress by securing it correctly,
and avoid impacts.
x Stow the rechargeable battery so that it will not be warmed up by sunlight or other
heat sources.
x When lifting the pedelec/S-pedelec, note that these are heavier than other cycles
and have a different weight distribution.
The braking and lateral forces acting on the bike carrier are higher with pedelecs/
S-pedelecs than with conventional bikes.
x Check whether your bike carrier is suitable for pedelecs/S-pedelecs.
x Ask a dealer about suitable bike carriers for your pedelec/S-pedelec.
1.20.1.2 By other means
The transportation of pedelecs/S-pedelecs with a rechargeable battery is subject to
particular regulations which are constantly being extended or updated.
These regulations may vary depending on the mode of transport used.
x Ask the rail company, airline or ferry operator about applicable regulations for
transporting pedelecs/S-pedelecs in good time before your departure. When doing
so, have the technical specifications for your pedelec/S-pedelec to hand.
1.20.2 Transporting or shipping the rechargeable battery
Separately transported lithium-ion batteries are hazardous goods. Undamaged rechargeable
batteries may be transported by private users on the road without further requirements.
x Acquaint yourself with national and regional road regulations about transporting
hazardous goods.
The rechargeable battery must not be carried on a plane as hand luggage.
x Observe specific requirements with regard to packaging and labelling for
transportation, e.g. when transporting by air or contracting a carrier.
x Find out about transporting rechargeable batteries and suitable transport
packaging by asking a carrier or dealer directly, for example.
x Ensure that rechargeable batteries transported in hand luggage or in a rucksack,
e.g. as spare batteries, are protected against liquids and short circuits.
x Do not continue to use rechargeable batteries after a fall. Have rechargeable
batteries checked before their next use.
Pedelec/S-pedelec Safety notes
13
2 Safety notes
This chapter covers notes on the rechargeable battery. Even if all safety precautions are
observed, the rechargeable battery can still become dangerous, such as if it catches fire.
x In an emergency, make sure that your actions do not put you or other people in
danger at any time.
x The instructions in this chapter must be followed in the event of an emergency.
x Read these instructions so that you can be focussed and prepared when reacting
to an emergency.
x Refer to and follow the enclosed system manuals.
2.1 Usage safety notes
WARNING
Danger to children and people with reduced physical, sensory
or mental capabilities or with a lack of experience and expertise,
e.g. children or people with physical or mental limitations.
Risk of accident and injury!
x Only allow the pedelec/S-pedelec, rechargeable battery and
charger to be used by people who have been instructed in
how to use them safely and properly, and who understand the
risks resulting from their use.
x Do not allow children to play with the pedelec/S-pedelec.
x Supervise children using the pedelec.
x Instruct children in how to handle the pedelec.
WARNING
Malfunctions and danger due to repairs without expertise.
Risk of accident and injury!
x Have repairs carried out by a dealer.
Pedelec/S-pedelecSafety notes
14
NOTE
Limited use of the pedelec/S-pedelec due to high and low
temperatures.
Risk of damage!
x Observe temperature limits.
x Avoid transporting the rechargeable battery by car in high
outdoor temperatures. Ensure that you park the car in the
shade when transporting the rechargeable battery by car.
x Do not park the pedelec/S-pedelec near heat sources.
x Avoid direct sunlight on the rechargeable battery when
parking the pedelec/S-pedelec.
2.2 Road safety notes
WARNING
Incorrect or improper use of the pedelec/S-pedelec.
Risk of accident and injury!
x Only use the cycle on public roads if its equipment meets
national and regional road regulations.
x Refer to and follow national and regional road regulations.
WARNING
Lack of protective headgear.
Risk of injury!
x Wear a suitable fitted helmet when riding.
Pedelec/S-pedelec Safety notes
15
2.3 Charger safety notes
DANGER
Electric shock due to handling the electric current and live
components incorrectly.
Risk of death!
x Check the charger, mains cable and mains plug for damage
before each use.
x If you find or suspect any damage, do not use the charger.
x Only use the charger indoors and do not leave it unattended
during use.
x Connect the charger solely to a properly installed plug socket
that meets the technical specifications of your charger.
x Make sure that the charger never comes into contact with
water or other liquids.
Pedelec/S-pedelecSafety notes
16
WARNING
Incorrect use of the charger.
Risk of short circuit followed by fire!
x Check the charger, mains cable and mains plug for damage
before each use.
x If you find or suspect any damage, do not use the charger.
x Place the charger so that it cannot become damp or wet.
x Never clean or spray the charger with liquid.
x Do not leave the charger unattended during use.
x If constant monitoring is not possible, then the charger may
only be used in rooms where a smoke detector is installed.
x The charger must not be used if any damage is found or
suspected.
x Do not open, dismantle, pierce or deform the charger.
x Repairs to the charger must only be carried out by a dealer,
and only using original spare parts.
NOTE
Damage to the charger due to it being used incorrectly.
Risk of damage!
x Always place the charger on fireproof material
(e.g. stone, glass, ceramic) when charging.
x Use the charger solely to charge the original rechargeable battery.
x Always pull the mains plug out of the socket after using the
charger.
x Pull on the plug and not the cable when disconnecting the
charger from the mains after charging.
x Read the additional safety notes on the charger housing.
Pedelec/S-pedelec Safety notes
17
2.4 Rechargeable battery safety notes
DANGER
Poisoning or fatal injury from leaking fumes and/or hydrofluoric
acid in the event of the rechargeable battery catching fire.
Risk of death!
x Remove yourself and other people from the vicinity of the
burning battery.
WARNING
Damage to the rechargeable battery can cause fires and
explosions.
Risk of fire and explosion!
x Do not attempt to put out the rechargeable battery yourself.
x Keep back from the rechargeable battery and let it burn out in
a controlled way.
WARNING
Internal damage to the rechargeable battery can cause
overheating or result in liquid and gas leaking from the battery.
Risk of fire and explosion!
x Have the rechargeable battery checked by a dealer after falls
or hard impacts.
x Do not open, dismantle, pierce or deform the rechargeable
battery and battery housing.
Pedelec/S-pedelecSafety notes
18
CAUTION
Injury to skin or eyes from leaking lithium in the event that the
rechargeable battery is damaged.
Risk of injury!
x Only touch damaged rechargeable batteries with protective
gloves.
x Wear safety goggles and an apron when in contact with a
damaged rechargeable battery.
NOTE
Damage to the drive and rechargeable battery due to charging
incorrectly.
Risk of damage!
x Do not charge the battery if you suspect it is damaged.
x It is essential that you read the “Operation / Rechargeable
battery / Charging the battery” chapter before charging the
battery for the first time.
x Only charge the battery with the original charger, and do not
leave it unattended while charging.
x Always place the rechargeable battery on fireproof material
(e.g. stone, glass, ceramic) when charging.
x If in doubt, have your dealer explain how to use rechargeable
batteries.
Pedelec/S-pedelec Safety notes
19
NOTE
Damage to the rechargeable battery, drive or nearby items due to
using the battery incorrectly.
Risk of damage!
x Use the rechargeable battery supplied solely for the original
drive.
x Keep the rechargeable battery away from fire and other heat
sources, and protect it against strong sunlight.
x Protect the rechargeable battery against moisture.
Never clean or spray the rechargeable battery with liquid.
x Do not use the rechargeable battery if you notice unusual heat
or discolouration, or if the battery is obviously damaged.
2.5 Residual risks
Even if all safety notes and warnings are observed, using the pedelec/S-pedelec still
entails unforeseeable risks such as:
Drivers and pedestrians failing to realise at first glance that a pedelec/S-pedelec
may be travelling at a higher speed.
Damage to the rechargeable battery caused by either low or high temperatures or
by direct sunlight.
Battery malfunction.
2.6 General safety precautions
If the rechargeable battery is found to be faulty or damaged:
x Do not use the rechargeable battery.
x Wear protective gloves when touching the rechargeable battery.
x Wear safety goggles for your own protection.
x Do not breathe in any leaking gases or steam.
x Avoid skin contact with leaking fluid.
Pedelec/S-pedelecBasic adjustments
20
2.6.1 In case of excessive heat
If the rechargeable battery is found to generate excessive heat:
x Remove the rechargeable battery if you can do so safely.
x Choose a temporary storage location outdoors and store the rechargeable battery
in a fireproof container or place it on fireproof ground.
x If storing the rechargeable battery outdoors, clearly secure a wide area around the
storage location.
x Have the rechargeable battery checked by a dealer straight away.
2.6.2 In case of deformation, odour or fluid
If the rechargeable battery is found to be deformed, producing an odour or leaking fluid:
x Remove the rechargeable battery if you can do so safely.
x If you can move the rechargeable battery safely, place it in a fireproof and
acid-resistant container, such as one made of stone or clay.
x Choose a fireproof temporary storage location outdoors. If storing the rechargeable
battery outdoors, clearly secure a wide area around the storage location.
x Have the rechargeable battery disposed of by a dealer immediately.
3 Basic adjustments
This chapter contains information about basic adjustments to the pedelec/S-pedelec,
and information about how to put the cycle into use.
3.1 Preparations
This chapter contains information about how to prepare the pedelec/S-pedelec for use.
3.1.1 Pedelec/S-pedelec adjustments to suit the rider
Individual adjustments are described in the “Basic adjustments” chapter of the “Cycle”
user manual.
3.1.2 Notes on the key
x The key number(s) stamped on the key should be recorded on your cycle
passport.
x If you lose the key, contact a dealer for a replacement.
Pedelec/S-pedelec Basic adjustments
21
3.1.3 Charger
x Refer to the information enclosed by the manufacturer about the charger.
x Read the specifications on the charger nameplate.
x If these specifications do not match the voltage supply, do not use the charger.
x Before connecting the charger to the voltage supply, read the “Operation /
Rechargeable battery / Charging the battery” chapter.
3.1.4 Rechargeable battery
x Charge the battery fully (see the “Operation / Rechargeable battery / Charging the
battery” chapter).
3.2 Before every ride
The pedelec/S-pedelec must be checked according to the “Basic adjustments /
Inspection instructions” chapter.
3.3 Before the first ride
CAUTION
Unexpected pedelec/S-pedelec behaviour due to incorrect
operation.
Risk of accident and injury!
x Familiarise yourself with the “Operation” chapter before
switching the cycle on for the first time.
The rechargeable battery is fully charged before your first ride (see the “Operation /
Rechargeable battery / Charging the battery” chapter).
Pedelec/S-pedelecBasic adjustments
22
3.4 First ride
The components of the electric drive are the main differences between a conventional
bike and a pedelec/S-pedelec. Information on the differences between bikes, pedelecs
and S-pedelecs can be found in the “Basics / Pedelec and S-pedelec differences” and
“Basics / Differences between a pedelec/S-pedelec and bike” chapters.
x Read these chapters carefully before your first ride.
x Practice operation and use off the road in an open space on even, solid ground
with good grip.
x Refer to the control unit information enclosed by the manufacturer.
1. Practice using the pushing aid.
2. Practice using the pedelec/S-pedelec and its features without motor assistance at
first. Then gradually increase the strength of the assistance.
3. Choose the lowest level of assistance on the control unit.
4. Start slowly.
5. Operate the brakes carefully and get accustomed to the brake action
(see the “Brake” chapter in the cycle user manual).
x When you can operate the brakes safely, get accustomed to the assistance
from the drive.
x When you can ride safely, repeat the familiarisation process and brake test for
the other gears.
3.5 Inspection instructions
Note the following points before every ride:
x Regularly check your pedelec/S-pedelec according to the inspection instructions in
the “Cycle” user manual (see the “Before setting off / Before every ride” chapter in
the cycle user manual).
x Check whether the lock for the rechargeable battery is fastened.
x Check the rechargeable battery for damage (visual inspection).
x Check the drive for damage (visual inspection).
x Check whether cables and connectors are securely in place and look for damage
(visual inspection).
x If you discover any missing or damaged parts, do not use the pedelec/S-pedelec.
x Have the pedelec/S-pedelec repaired by a dealer.
x Prepare the rechargeable battery and the charger for putting your pedelec/S-pedelec
into operation.
x If you own an S-pedelec, check whether your insurance plate is still valid.
Pedelec/S-pedelec Operation
23
4 Operation
Different drive units may be installed depending on the cycle model.
x Acquaint yourself with how to operate the drive before your first ride.
x Refer to and follow the enclosed system manuals.
x Have your dealer instruct you on operating the drive.
4.1 Pedelec/S-pedelec
CAUTION
Unexpected pedelec/S-pedelec behaviour due to incorrect
operation.
Risk of accident and injury!
x Familiarise yourself with the “Operation” chapter before
switching the cycle on for the first time.
4.1.1 Switching the drive on/off
x To switch the drive on and off, press the On/Off button on the control unit.
x Note that there must be no load on the pedals when switching the drive on.
4.1.2 Switching the lighting on/off
WARNING
Poor visibility on the road.
Risk of accident and injury!
x Before setting off, make sure that your pedelec/S-pedelec has
enough battery charge to power the lighting during the ride.
x Use the control unit to switch the lighting on or off.
Pedelec/S-pedelecOperation
24
4.2 Drive overheating protection
CAUTION
Overheating of the drive and rechargeable battery in the event of
a malfunction.
Risk of burning!
x Avoid contact with the drive and rechargeable battery.
The drive is automatically protected against damage due to overheating. When the drive
temperature is too high, the drive switches off automatically.
x To prevent the drive overheating, use a low level of assistance from the drive in high
outdoor temperatures or on steep inclines.
x If the drive switches off while riding with a charged battery, temporarily use the
pedelec/S-pedelec like a conventional bike so that the drive can cool down.
Switch off the assistance.
x If the fault is not corrected by letting the drive cool down, have the pedelec/
S-pedelec checked by a dealer.
4.3 Control unit
CAUTION
Delayed rider reaction due to distraction.
Risk of accident and injury!
x Familiarise yourself with the control unit features.
x Familiarise yourself with the control unit features so that you can focus completely
on the road.
Pedelec/S-pedelec Operation
25
4.3.1 Pedelec pushing aid
CAUTION
Pinching and crushing of body parts by moving components.
Risk of injury!
x Only use the “pushing aid” feature when pushing the pedelec.
x Only use the pushing aid when the pedelec is standing on
both wheels.
Depending on the model, the pedelec may be equipped with a pushing aid.
The pushing aid makes it easier to push the pedelec.
The speed of this feature depends on what gear is engaged. The maximum is 6 km/h
(USA: There may be a pushing aid depending on the cycle model� How this
functions is described in more detail in the drive system user manual enclosed
with the cycle�). The lower the selected gear, the lower the speed of the pushing aid.
4.3.2 S-pedelec starting aid
The following section is only applicable for Europe:
The S-pedelec is equipped with a starting aid up to a maximum of 18 km/h.
This starting aid is all-electric and does not require pedal assistance.
4.4 Rechargeable battery
NOTE
Irreparable damage to the pedelec/S-pedelec due to
self-discharge for technical reasons.
Risk of damage!
x Recharge an empty battery straight away.
Pedelecs/S-pedelecs are usually equipped with a lithium-ion (li-ion) rechargeable
battery. With proper use, li-ion batteries are safe.
Li-ion batteries have a high energy density, and so great attention is required when using
these rechargeable batteries.
Pedelec/S-pedelecOperation
26
For rider safety, reliable operation and a long service life, it is essential to note the
following:
After the first full charge, the battery can be partially charged. Partially charging
the battery will not damage it, as lithium-ion rechargeable batteries do not have a
memory effect.
Partial charges are rated proportionally to their capacity (a charge of 50 % corresponds
to half a charge/discharge cycle).
Temperature limits must be observed for the rechargeable battery to function properly.
x Refer to the information enclosed by the manufacturer about the rechargeable
battery as well as the enclosed drive system manuals.
Note that ambient temperatures below +10 °C and above +40 °C/below 50 °F and
above 104 °F can reduce the range.
Particularly high and particularly low ambient temperatures can permanently speed
up battery wear or even damage the rechargeable battery.
x The rechargeable battery is subject to a certain degree of wear. Refer to the
warranty terms for exact charge/discharge cycle specifications and corresponding
power loss figures.
x If you experience excessive power loss, e.g. operating time is significantly
shortened, have the rechargeable battery checked by a dealer.
x Never make any alterations to the rechargeable battery yourself.
4.4.1 Safety feature
CAUTION
Overheating of the drive and rechargeable battery in the event of
a malfunction.
Risk of burning!
x Avoid contact with the drive and rechargeable battery.
The rechargeable battery and/or the charger are equipped with a temperature control
which only allows charging when the temperature is between 0 °C and +45 °C/between
32 °F and 113 °F.
If the rechargeable battery is outside these temperature limits, the charging process is
stopped automatically.
x Refer to and follow the notes in the system manual if charging stops prematurely.
Pedelec/S-pedelec Operation
27
4.4.2 Rechargeable battery and charger applications
The drive, rechargeable battery and charger are designed for each other and approved
solely for use with the pedelec/S-pedelec.
4.4.3 Riding with an empty battery
If the battery charge is completely used up during a ride, the pedelec/S-pedelec can be
used like a conventional bike.
x Note that using a pedelec/S-pedelec without assistance is more difficult than using
a conventional bike.
4.4.4 Removing/inserting the rechargeable battery
NOTE
Damage to the electronics due to removing the rechargeable
battery incorrectly.
Risk of damage!
x Switch off the drive before removing the rechargeable battery.
NOTE
Damage to the rechargeable battery due to dropping.
Risk of damage!
x Before use, check that the rechargeable battery is correctly
inserted in the holder and that the lock is engaged.
The rechargeable battery may be removed/inserted differently depending on the drive
system.
x Refer to the enclosed system manuals.
Pedelec/S-pedelecOperation
28
4.4.5 Charging the battery
WARNING
Heat, leaking gas and damage to the rechargeable battery due to
incorrect charging.
Risk of injury and fire!
x Do not use or touch the rechargeable battery and charger
if you notice unusual heat, odour or discolouration, or if the
battery is obviously damaged.
x Pull the charger plug out of the socket.
x Pull on the plug and not the cable when disconnecting the
charger from the mains after charging.
With some models, the battery can be charged while it is inserted in the pedelec/
S-pedelec. With other models, the battery must be removed before charging.
x Only charge the battery in a dry, well-ventilated room.
x If you can shelter your pedelec/S-pedelec in a dry and safe place, e.g. in a garage
or bike shed, charge the battery while it is inserted.
x If you cannot shelter your pedelec/S-pedelec, remove the battery to charge it
(see the “Operation / Rechargeable battery / Removing/inserting the rechargeable
battery” chapter).
x Remove any dirt from the charging port and contacts with a dry cloth.
x Do not leave the rechargeable battery unattended while charging.
x Charging a battery while inserted: Switch off the pedelec/S-pedelec to charge the
battery.
x Charging a battery while removed: Always place the charger on fireproof material
(e.g. stone, glass, ceramic) when charging.
4.4.6 Connecting the rechargeable battery to the charger
1. Insert the charging plug on the charger into the charging port on the rechargeable
battery or the battery holder.
2. Ensure that you line up the charging plug so that the contacts on the charging plug
match those on the charging port.
3. Monitor the charging process.
Pedelec/S-pedelec Cleaning and maintenance
29
4.4.7 Stopping the charging process
Charging can be stopped before the battery is fully charged, e.g. for storage
(see the “Storage / Storing the rechargeable battery” chapter).
4.4.8 Charging times
When the rechargeable battery is empty, a full charging process generally takes between
3 and 6 hours. The duration of the battery charging process is dependent on the
following factors:
Battery charge level
Battery temperature and ambient temperature
Battery capacity
Battery model
Charger
5 Cleaning and maintenance
WARNING
Injury from electric current during cleaning, maintenance and
repair work.
Risk of electric shock and short circuit!
x Pull the charger plug out of the socket.
x Pull on the plug and not the cable when disconnecting the
charger from the mains.
x Remove the rechargeable battery from the pedelec/
S-pedelec before cleaning and maintenance.
x Do not clean the components with running water or other
liquids.
x Do not use high-pressure equipment for cleaning.
Pedelec/S-pedelecCleaning and maintenance
30
WARNING
Touching hot components.
Risk of burning!
x Let the drive and rechargeable battery cool down before
touching the components.
x Refer to the “Cycle” user manual for information about cleaning and maintenance.
x Check safety-related components before every ride (see the “Basic adjustments /
Before every ride” chapter).
x Check your pedelec/S-pedelec after a fall.
x Have maintenance work carried out by a dealer.
5.1 Checking the electric drive system
x Refer to the enclosed system manuals.
x Check all electrical cables for damage.
x Examine the display for cracks and damage, and check that it is firmly in place.
x Check the control unit for cracks and damage, and check that it is firmly in place.
x Check the rechargeable battery for damage.
x Check that all plug contacts are properly in place and reconnect them if necessary.
x Check the cable harness for damage. Check that the outer casing is undamaged.
x Carry out a visual inspection of the auxiliary motor.
5.2 Troubleshooting
WARNING
Working on the pedelec/S-pedelec with the rechargeable battery
inserted or the charger connected.
Risk of electric shock!
x Remove the rechargeable battery from the holder.
x Disconnect the charger from the voltage supply.
Pedelec/S-pedelec Cleaning and maintenance
31
CAUTION
Fingers caught in moving parts.
Risk of injury!
x Remove the rechargeable battery from the holder before
carrying out maintenance work.
CAUTION
The drive and rechargeable battery may become hot in the event
of a malfunction.
Risk of burning!
x Let the drive and rechargeable battery cool down before
touching them.
The components of the pedelec/S-pedelec are automatically checked on an ongoing
basis. If a fault is found, an appropriate error message will appear on the display.
x Refer to the enclosed system manuals.
x If the actions listed do not solve the problem, contact a dealer.
Depending on the fault type, the drive may be switched off automatically.
You can continue to ride without assistance from the drive.
x Contact a dealer to have the drive checked before your next ride.
Pedelec/S-pedelecStorage
32
6 Storage
6.1 Storing the rechargeable battery
WARNING
Respiratory tract, eye or skin irritation from leaking fumes or fluid
in the event of damage to or improper use of the rechargeable
battery.
Risk of injury!
x If you experience symptoms, seek medical advice straight away.
x Make sure there is an ample supply of fresh air if the
rechargeable battery is defective.
x Remove contaminated clothing immediately.
x Avoid contact with the battery fluid.
x If battery fluid gets into your eyes, rinse them out with plenty
of water. Seek advice from a doctor immediately.
x Wash your skin thoroughly with soap and water.
If the rechargeable battery will not be used for a prolonged period, the following points
must be noted with regard to storage:
x Charge the battery to around 60 % of its capacity.
x If necessary, remove the rechargeable battery from the holder to store it.
x Store the rechargeable battery out of reach of children and animals, and in such a
way that it cannot fall down.
x Store the rechargeable battery ideally at around +10 °C to +15 °C /around 50 °F to
59 °F, in a dry and well-ventilated place such as an appropriate basement room.
x Protect the rechargeable battery against moisture.
x Ensure that the temperature remains between the upper and lower limits during
storage.
x If storing for more than 3 months, recharge the battery every three to six months,
depending on storage conditions. Charge the battery to around 60 % of its
capacity again at these times.
Pedelec/S-pedelec Disposal
33
x Always disconnect the rechargeable battery from the charger and the charger
from the voltage supply after charging.
x When storing the rechargeable battery, ensure that the poles do not short-circuit.
Cover the poles with masking tape if necessary.
6.2 Storing the pedelec/S-pedelec
If the pedelec/S-pedelec will not be used for a prolonged period, the following points
must be noted with regard to storage:
x Clean the pedelec/S-pedelec (see the “Cleaning and maintenance” chapter).
x Protect the pedelec/S-pedelec against moisture, dust and dirt during storage.
x Store the pedelec/S-pedelec in a dry, frost-free place where it is protected against
major fluctuations in temperature.
x To prevent tyre deformation, store the pedelec/S-pedelec hanging by its frame.
7 Disposal
This chapter contains notes on environmentally friendly disposal, by way of example.
Acquaint yourself with the national and regional regulations in your country.
7.1 Cycle
Do not dispose of your cycle in household waste. Take it to a municipal collection point
or a recycling centre.
Alternatively, there are also collections organised by local councils and private
organisations. Contact your local council about this or refer to postal information.
7.2 Electrical elements, single-use batteries and
rechargeable batteries
Pedelecs, S-pedelecs and bikes with electric shifting
systems or electric damper systems must have all single-use
and rechargeable batteries removed first, along with any
detachable controls containing batteries. This means drive
system batteries, displays with a fixed rechargeable battery,
rechargeable batteries installed in or on the frame for shifting
or damper systems, etc. Displays with a fixed rechargeable
battery, displays which allow the screen to remain active after removal from the holder
and which do not have a visible battery compartment on the back are intended for
disposal as a whole.
Pedelec/S-pedelecDisposal
34
Only externally accessible battery compartments (generally for button cell batteries) may
be opened. The display housing must not be opened to remove a fixed rechargeable
battery.
Fixed rechargeable batteries in displays are generally lithium-ion batteries and therefore
hazardous waste. They must not be disposed of in household waste, and must be taken
to a municipal collection point or a recycling centre instead.
This also applies to replaced batteries which can no longer be used due to wear or a
defect. Please also refer to the “Safety notes / Rechargeable battery safety notes” chapter.
Commercially available single-use batteries can be taken to a municipal collection point
or a recycling centre, and can also placed in battery collection boxes which are available
in various shops or stores.
After removing any single-use or rechargeable batteries, the remainder of the cycle is classed
as waste electrical and electronic equipment and must be sent for recycling separately.
Your dealer, the municipal collection point or a recycling centre can assist you here.
7.3 Electronic components and accessories
Replaced or defective LED headlamps, LED rear lamps or hub dynamos, as well as
accessories such as bike computers or navigation devices, must also be disposed of
separately.
Take parts and devices of this kind to a municipal collection point or a recycling centre.
7.4 Packaging
The packaging used to protect your cycle during shipping, called transport packaging,
can generally be left with your dealer. All other types of packaging must be sorted and
disposed of separately. Dispose of cardboard along with waste paper and film in your
recycling collection, or ask your dealer about disposal.
7.5 Tyres and inner tubes
Tyres and inner tubes must not be disposed of in household waste.
Ask your dealer whether they take care of collection and disposal, or take these items to
a recycling centre or municipal collection point.
7.6 Lubricants and care products
Do not dispose of lubricants and care products in household waste, into the sewer system
or into the environment. They must be taken to a hazardous waste collection point.
Also follow the notes included on the lubricant and care product packaging.
Winora Group
Supplementary
User manual
Children’s bike
Children’s bike
1 Handlebar grips and handlebars 11 Chain case
2 Brake lever 12 Seat tube
3 Front brake 13 Chain stays
4 Tyre 14 Seat stays
5 Rim 15 Stabiliser (training wheel)
6 Spoke 16 Rear wheel hub
7 Front wheel hub 17 Seat post clamp
8 Valve 18 Saddle
9 Down tube 19 Top tube
10 Pedal
Example illustration
1
2
3
4
5
6
9
8
7
10
13
12
14
15
16
19
17
18
11
Children’s bike
Contents
1 General notes � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
2 Safety notes� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
3 Residual risks � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
4 Proper use � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
5 Basics � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
5�1 Notes on road use � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
5�2 Notes on the brakes � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
5�3 Before every ride � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
5�4 Inspection instructions� � � � � � � � � � � � � � � � � � � � � � � � � � 8
5�5 Before the first ride� � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
6 Stabilisers � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
6�1 Fitting stabilisers � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
6�2 Removing stabilisers� � � � � � � � � � � � � � � � � � � � � � � � � � � 11
Children’s bike General notes
1
1 General notes
This user manual is a supplement and aimed at the child’s parent or guardian.
It assumes that you have read the “Cycle” user manual. Read the entire “Cycle”
user manual carefully, paying particular attention to the safety notes and notes
on adjustment and operation, before your child uses the children’s bike.
WARNING
Lack of road knowledge.
Risk of accident!
x Explain to your child the regulations on road behaviour.
x Explain to your child how to be defensive and careful on the
road.
x Only allow your child to use the children’s bike on the road
once they have understood the regulations on road behaviour.
x Only allow your child to ride on the road when accompanied
by a parent or guardian.
WARNING
Lack of knowledge about how to operate the children’s bike.
Risk of accident!
x Explain to your child how to operate the children’s bike.
x Only allow your child to use the children’s bike on the road
once they can operate it safely.
Children’s bikeGeneral notes
2
WARNING
Component breakage due to overloading.
Risk of accident and injury!
x Explain to your child that the children’s bike may only be used
by one person, and that other people must not be transported
on the luggage carrier, crossbar or handlebars.
x Ensure that the maximum gross weight limit for the children’s
bike is not exceeded.
WARNING
Insufficient knowledge or ability.
Risk of accident and injury!
x Do not allow the children’s bike to be used by children with
reduced physical, sensory or mental capabilities or with a lack
of experience and expertise.
x Do not allow children to carry out care and maintenance.
x Do not allow young children to play with the packaging
materials, particularly the packaging film. Children may
become entangled in it and suffocate or cut themselves.
x Read the entire user manual and explain all the contents to your child.
x Practice with your child how to ride on the road, and only allow them to ride alone
once you feel it is responsible to do so.
x Regularly check your child’s seating position and have adjustments made by a
dealer if necessary.
x Refer to the notes on minimum insertion depths for the saddle and handlebars
(see the “Basic adjustments / Saddle / Minimum insertion depth” and
“Basic adjustments / Handlebars and handlebar stems / Minimum insertion depth”
chapters in the cycle user manual).
Children’s bike Safety notes
3
2 Safety notes
WARNING
Longer braking distance and reduced traction due to slippery or
dirty roads.
Risk of accident and injury!
x Ensure that your child adapts their speed to suit the weather
and road conditions.
WARNING
High risk of accident following incorrect or improper use of the
children’s bike.
Risk of accident!
x Only allow your child to use the children’s bike on the road if
its equipment meets national road regulations.
x Only allow your child to use the children’s bike in compliance
with national and regional road regulations.
x Explain to your child the national and regional regulations on
using footpaths, bike paths and roads.
WARNING
Poor visibility due to incorrect clothing.
Risk of accident and injury!
x Only allow your child to ride on the road while wearing bright
and conspicuous clothing, e.g. with reflective elements.
Children’s bikeSafety notes
4
WARNING
Lack of protective headgear.
Risk of injury!
x Only allow your child to use the children’s bike if they are
wearing a suitable fitted helmet.
x Have your dealer explain what helmets are suitable for your
child.
x Have your dealer show you how to use your child’s helmet.
WARNING
Inattentiveness on the road.
Risk of accident and injury!
x Explain to your child that they must not get distracted by other
activities while riding, e.g. switching on retrofitted lighting.
x Forbid your child from using mobile devices such as
smartphones or MP3 players while riding.
WARNING
Malfunctions in the children’s bike due to additions and
alterations using incorrect accessories.
Risk of accident and injury!
x Have alterations to the children’s bike carried out by your
dealer only.
x Only have accessories fitted that meet national road
regulations.
x Ask your dealer about suitable accessories.
Children’s bike Residual risks
5
WARNING
Frame or front fork breakage due to improper use of the
children’s bike.
Risk of accident and injury!
x Explain to your child that they must not jump over ramps or
mounds of earth with the children’s bike.
x Explain to your child that they must not ride the children’s bike
down slopes.
x Explain to your child that they must not ride the children’s bike
through deep puddles or near water.
x Explain to your child that they must not ride the children’s bike
through terrain that will make it excessively dirty.
x Explain to your child that they must not ride the children’s bike
over stairs, kerbs or other steps.
3 Residual risks
Even if all safety notes and warnings are observed, using the children’s bike still entails
unforeseeable risks such as:
Distraction from the road due to childish curiosity
Misjudgements by the child, for example with regard to traction, speed or their own
riding ability
Incorrect behaviour by other road users
Unforeseeable road conditions e.g. slipperiness due to black ice
Component breakage or failure due to unforeseeable material defects or material
fatigue.
Children’s bikeProper use
6
4 Proper use
Neither the manufacturer nor the dealer accept any liability for damage caused due to
improper or incorrect use.
Improper use of the children’s bike will invalidate the guarantee
(see the “Warranty” chapter in the cycle user manual).
The children’s bike is designed for use by one person, with the seating position correctly
adjusted to suit their height (see the “Basics / Seating position” chapter in the cycle user
manual). Carrying additional people, e.g. on the luggage carrier, is not permitted.
The maximum gross weight limit, if applicable, is marked on the frame of the children’s bike
as well as recorded on the data sheet provided by the dealer, and must not be exceeded.
Children’s bikes that are not equipped for use on the road are designed solely for
home use. For use on the road, the children’s bike must have or be retrofitted with the
equipment necessary to meet national and regional regulations.
The children’s bike is not designed for above-average stress; for example, use at races
and competitive events is deemed improper (see the “Warranty” chapter in the cycle
user manual).
The children’s bike is not designed for use with a child seat.
Proper use of the children’s bike on the road requires the person using the bike to know,
understand and apply national and regional regulations.
Proper use of the children’s bike on the road requires the bike to meet national and
regional regulations (see the “Safety / Notes on road use” chapter in the cycle user
manual).
Use the children’s bike only as described in this user manual. Any other use is deemed
improper and may result in accidents, injury or property damage.
5 Basics
This chapter contains notes on road use and information allowing the children’s bike to
be put into use.
5.1 Notes on road use
If a children’s
bike is to be used on the road but was not sold with equipment approved
for
road use, have the children’s bike retrofitted with approved components.
x Acquaint yourself with national and regional regulations on equipment for children’s
bikes before the first ride. For example:
Compulsory helmet use
Compulsory use of reflective safety vests
Brakes
Children’s bike Basics
7
Lighting and reflectors
Bell
x Only allow your child to ride on the road if the equipment meets national and
regional road regulations.
x If necessary, have the children’s bike retrofitted with any necessary equipment
prior to use on the road.
x Explain to your child the national and regional regulations on equipment for
children’s bikes.
x If in doubt, consult your dealer.
x Acquaint yourself with national and regional road regulations. Children and young
people are generally subject to different regulations than adults.
x Explain the traffic code to your child, along with how they should behave on
the road.
x Explain to your child the national and regional regulations on using:
Footpaths
Bike paths
Roads
x Only allow your child to ride on the road alone if:
This is permitted by national and regional regulations.
You are confident about your child using the road.
x Explain to your child how to be defensive and careful on the road.
x Teach your child to ride so as not to harm, endanger, impede or inconvenience anyone.
x Only allow your child to ride the children’s bike if they are wearing a suitable fitted
helmet. Consult a dealer about choosing a suitable helmet.
Many regions offer children’s courses where your child can have fun
learning how to ride and behave on the road.
Laws and regulations can change at any time, so acquaint yourself with
national and regional regulations on a regular basis and explain them to
your child.
Children’s bikeBasics
8
5.2 Notes on the brakes
The children’s bike is equipped with at least two independent brakes, one for the front
wheel and one for the rear wheel. One of these brakes or an additional brake may be a
coaster brake.
WARNING
The braking behaviour of a rim brake changes in the wet.
Risk of accident and injury!
x Have your child keep off the road while they practice braking
in the wet.
x Explain to your child that they must ride slowly in the wet.
5.3 Before every ride
The following points must be noted before every ride:
x Check the children’s bike thoroughly for damage and excessive wear before your
child uses it (see the “Basics / Inspection instructions” chapter).
x Explain to your child that they must not use the children’s bike if it is damaged.
5.4 Inspection instructions
The following points must be noted before every ride:
x Check the condition of the frame and components.
x Check all components for deformation, cracks and discolouration.
x Check whether the handlebars, pedals and saddle are correctly fastened and
adjusted (see the “Basic adjustments” in the cycle user manual).
x If your children’s bike is equipped with a luggage carrier, check whether the
carrier is correctly fastened.
x If your children’s bike is suitable for a luggage carrier and is retrofitted with one,
check whether the carrier is correctly fastened.
x Test the functionality of the brakes.
x Operate the brake levers and coaster brake, and listen for unusual noises.
x Check that the children’s bike is difficult or impossible to push with the brake
applied so that the bike can safely be brought to a standstill while riding.
x Check whether there is any brake pad grinding when the brake levers are released.
Children’s bike Basics
9
x Test the functionality of the lighting and bell.
x Switch on the lighting. Check whether the headlamp and rear lamp are lit.
To do so, turn the wheel where the dynamo is fitted, or check the battery
charge level if battery-powered lighting has been retrofitted.
x Check whether you hear a clear sound when you operate the bell.
5.5 Before the first ride
WARNING
Distraction of the child due to unexpected behaviour from the
children’s bike, e.g. when braking.
Risk of accident and injury!
x Only allow your child to use the children’s bike on the road once
they know how the bike behaves and are familiar with its operation.
The dealer will fully assemble the children’s bike and customise the handlebars, saddle
and brake levers for your child.
x When you receive the children’s bike, check whether your child can ride it
comfortably and safely, and that all the adjustments fit your child.
x Have adjustments carried out by a dealer only.
x If you make adjustments yourself, ask a dealer about the applicable torques
and use a torque wrench.
x If you make adjustments yourself, check them properly and thoroughly before
your child uses the children’s bike.
x Familiarise yourself with the children’s bike before your child rides it for the first
time, and explain all the controls to your child.
x Keeping off the road, practice with your child so that they get accustomed to the
handling characteristics of the children’s bike.
x Practice with your child how to mount, dismount and stop safely.
x Have your child practice braking, particularly using a coaster brake (if available), at
low speed.
x Have your child practice emergency braking.
x Practice with your child how to indicate direction when making turns, and how to
look over their shoulder.
x Only allow your child to ride the children’s bike once you feel it is responsible to do so.
Children’s bikeStabilisers
10
6 Stabilisers
Stabilisers (or training wheels) are auxiliary wheels that support a child while they are
learning to ride a bike. They prevent the children’s bike from tipping over.
x Assess whether your child needs stabilisers while learning to ride.
x If your child needs stabilisers while learning to ride, use the stabilisers supplied
(if applicable).
x If no stabilisers are supplied, contact your dealer about selecting and fitting suitable
stabilisers.
6.1 Fitting stabilisers
WARNING
Incorrectly or poorly fitted stabilisers can cause malfunctions
such as the rear wheel falling off.
Risk of accident and injury!
x If you lack the necessary expertise and the tools required to fit
the stabilisers, contact your dealer.
Depending on the model, suitable stabilisers may be supplied with the children’s bike.
The enclosed stabilisers should be used if stabilisers are required.
Care is required when fitting the stabilisers so that they serve their purpose correctly and
safely.
x If stabilisers are not supplied, ensure that they are purchased to fit the children’s
bike. The bolts on the rear wheel of the children’s bike must be long enough that
the stabilisers can be securely fastened on both sides.
x Consult your dealer about suitable stabilisers if necessary.
x Refer to information from the manufacturer about fitting stabilisers.
1. Completely unscrew the cap nuts from both sides of the axle by turning them
anticlockwise.
2. Remove the attached hub axle washer from the axle.
Stabilisers often consist of several parts.
Children’s bike Stabilisers
11
3. Assemble them as described in the
manufacturer’s instructions.
4. Attach the first assembled stabiliser to
the axle of the children’s bike, push the
hub axle washer onto the axle and
tighten the cap nut again, observing the
applicable torque (see “Illustr.: Fitting a
stabiliser”).
5. Attach the second assembled stabiliser
to the axle of the children’s bike, push
the hub axle washer onto the axle and
tighten the cap nut again, observing the
applicable torque (see “Illustr.: Fitting a
stabiliser”).
x When tightening the cap nut, ensure
that the rear wheel forms a straight
line with the frame and front wheel.
x When tightening the cap nut, ensure
that the chain is still tensioned.
The stabilisers are height-adjustable.
x Check where the slotted holes for this purpose are positioned on the stabilisers
that you installed. Refer to the fitting information enclosed by the manufacturer.
Both stabilisers should be the same distance from the ground. When holding the
children’s bike straight, the stabilisers should not touch the ground.
6.2 Removing stabilisers
1. Turn both cap nuts until you can remove them from the axle.
2. One by one, remove the hub axle washers and the stabilisers from the axle.
3. Push the hub axle washers onto the axle and tighten the cap nuts, observing the
applicable torque.
4. When tightening the cap nut, ensure that the rear wheel forms a straight line with
the frame and front wheel.
5. When tightening the cap nut, ensure that the chain is still tensioned.
2
3
4
Illustr.: Fitting a stabiliser (example)
1 Rear wheel axle
2 Hub axle washer
3 Cap nut
4 Stabiliser (training wheel)
1
Winora Group
User manual
Balance bike
Balance bike
1 Handlebar grips and handlebars 6 Seat tube
2 Tyre 7 Wheel hub with cap nut
3 Rim 8 Seat post clamp
4 Spoke 9 Saddle
5 Valve
Example illustration
1
2
3
4
5
6
7
8
9
Balance bike
Contents
1 Basics � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
1�1 Applicability � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1
1�2 Reading and storing the user manual � � � � � � � � � � � � � � � � � � 1
1�3 Notes on screw turning directions � � � � � � � � � � � � � � � � � � � 1
1�4 Notes on torques� � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
2 Safety notes� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
3 Residual risks � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
4 Proper use � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
5 Age rating � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
6 Use � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
6�1 A note on braking � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
6�2 Helmet � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
6�3 Before every ride � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
6�4 Inspection instructions� � � � � � � � � � � � � � � � � � � � � � � � � � 9
6�5 Before the first ride� � � � � � � � � � � � � � � � � � � � � � � � � � � � 9
6�6 After a fall� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
7 Basic adjustments� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
7�1 Adjusting the saddle � � � � � � � � � � � � � � � � � � � � � � � � � � � 11
7�2 Checking and adjusting the tyre pressure � � � � � � � � � � � � � � � 12
7�3 Reducing the tyre pressure � � � � � � � � � � � � � � � � � � � � � � � 13
8 Cleaning� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14
8�1 Cleaning products required � � � � � � � � � � � � � � � � � � � � � � � 14
8�2 Cleaning the balance bike � � � � � � � � � � � � � � � � � � � � � � � � 14
Balance bike
9 Maintenance � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 15*
9�1 Inspection intervals � � � � � � � � � � � � � � � � � � � � � � � � � � � 17
9�2 Checking the screw joints � � � � � � � � � � � � � � � � � � � � � � � � 17
9�3 Checking the frame and front fork� � � � � � � � � � � � � � � � � � � � 17
9�4 Checking the saddle � � � � � � � � � � � � � � � � � � � � � � � � � � � 18
9�5 Checking the handlebars � � � � � � � � � � � � � � � � � � � � � � � � 18
9�6 Checking the front wheel and rear wheel � � � � � � � � � � � � � � � � 19
9�7 Checking the rims and spokes � � � � � � � � � � � � � � � � � � � � � 19
9�8 Checking the tyres � � � � � � � � � � � � � � � � � � � � � � � � � � � � 19
9�9 Checking the safety elements � � � � � � � � � � � � � � � � � � � � � � 20
10 Storage � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20
11 Warranty� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20
12 Guarantee � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21
13 Disposal � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21
13�1 Balance bike � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21
13�2 Packaging� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21
13�3 Tyres and inner tubes� � � � � � � � � � � � � � � � � � � � � � � � � � 22
13�4 Lubricants and care products � � � � � � � � � � � � � � � � � � � � � 22
14 Declaration of conformity � � � � � � � � � � � � � � � � � � � � � � � � � � � � 22
*Chapters where additional information is available to you in the
online operating manual can be identified by the blue underlined text:
9Maintenance.
Balance bike Basics
1
1 Basics
1.1 Applicability
This user manual applies to balance bikes which are not approved for use on the road.
The balance bike is marked with the following cycle category symbol.
Symbol Cycle category Use
12" balance bike Only for use under adult supervision.
Not suitable for use on the road. Maximum
gross weight limit: 30 kg/66 lbs.
1.2 Reading and storing the user manual
This user manual contains important information about using the balance bike,
and is aimed at parents and guardians. Read all the warnings and notes in this
user manual carefully before allowing your child to use the balance bike, and
explain all the contents to your child.
Only allow your child to use the balance bike once you have read and
understood this user manual.
Keep the user manual to hand so that it is available at all times. If passing the
balance bike on to a third party, include the user manual along with it.
1.3 Notes on screw turning directions
NOTE
Material damage due to handling screw joints incorrectly.
Risk of damage!
x Observe the turning direction of screws, thru-axles and nuts.
x Tighten screws, thru-axles and nuts by turning them clockwise.
x Loosen screws, thru-axles and nuts by turning them anticlockwise.
In the event of any deviation from this rule, the change in turning direction
will be indicated in the respective chapter. Refer to the relevant notes.
Balance bikeBasics
2
1.4 Notes on torques
WARNING
Material fatigue due to tightening screw joints incorrectly.
Risk of accident and injury!
x Do not allow your child to use the balance bike if you find any
loose screw joints.
x Screw joints must be properly tightened with a torque wrench.
x Screw joints must be tightened using the correct torques.
To correctly tighten the screw joints, the applicable torques must be observed.
This requires a torque wrench with an appropriate adjustment range.
x If you have no experience with using torque wrenches or do not own a suitable
torque wrench, have the screw joints checked by your dealer.
The correct torque for a screw joint is dependent on the material and diameter of the
screw, as well as the material and design of the component.
x If tightening screw joints, check whether the balance bike is equipped with
aluminium components (see the specifications data sheet provided by the dealer).
x Observe the specific torques for aluminium components.
Individual components on the balance bike are labelled with torque specifications or
insertion depth markings.
x Follow these specifications and markings.
Balance bike Safety notes
3
2 Safety notes
WARNING
Entanglement and suffocation or injury due to playing with
packaging material.
Risk of suffocation and injury!
x Do not allow young children to play with the packaging
materials, particularly the packaging film. Children may
become entangled in it and suffocate or cut themselves.
WARNING
Swallowing small parts.
Risk of suffocation!
x Do not allow your child to play with small parts that could be
swallowed.
WARNING
Danger for the child due to using the balance bike without
supervision.
Risk of accident and injury!
x Supervise your child when they are playing with the balance
bike.
x Only allow your child to ride while wearing bright and
conspicuous clothing, e.g. with reflective elements.
x Do not allow your child to ride near stairs, kerbs, slopes or
water.
x Do not allow your child to ride in areas with traffic
(e.g. parking facilities or private courtyards).
Balance bikeSafety notes
4
WARNING
Danger for the child due to operating the balance bike incorrectly.
Risk of accident and injury!
x Explain to your child how to operate the balance bike.
x Teach your child about the dangers, e.g. falls and collisions,
which could arise through using the balance bike.
x Practice with your child how to use the balance bike so as to
prevent falls or collisions.
WARNING
Longer braking distance and reduced traction due to slippery or
dirty roads.
Risk of accident and injury!
x Explain to your child that they must adapt their riding style and
speed
to suit the weather and road conditions.
x Ensure that your child adapts
their riding style and speed
to
suit the weather and road conditions.
WARNING
Injury due to lack of or incorrect footwear.
Risk of accident and injury!
x Only allow your child to use the balance bike when they are
wearing closed toe, non-slip shoes with hard soles.
Balance bike Safety notes
5
WARNING
Risk of injury due to falling without a helmet or protective gear.
Risk of injury!
x Only allow your child to use the balance bike when
they are
wearing a suitable fitted helmet
.
x Only allow your child to use the balance bike when they are
wearing protectors such as elbow and knee pads.
x Only allow your child to use the balance bike when they are
wearing long and, if necessary, padded clothing.
CAUTION
Danger for the child due to using the balance bike on unsuitable
ground.
Risk of accident and injury!
x Only allow your child to ride on clean, dry and even
ground.
x Do not allow your child to play on cross-country terrain or on
steep paths.
CAUTION
Pinch points on the balance bike.
Risk of accident and injury!
x Only allow your child to use the balance bike when they are
wearing close-fitting clothing on their legs.
x Ensure that items of clothing, such as laces or belts, cannot
become entangled in moving parts.
Balance bikeResidual risks
6
CAUTION
Missing safety elements.
Risk of injury!
x Before every ride, check that all safety elements such as
protective caps on nuts, the bumpers on the handlebar stem
and the ends of the handlebar grips are properly fitted and
undamaged.
CAUTION
Malfunction of the balance bike due to improper additions or
alterations to the bike or incorrect accessories.
Risk of accident and injury!
x Have your dealer carry out alterations to the balance bike.
x Only have original accessories fitted.
x Do not have any accessories with sharp edges fitted.
3 Residual risks
Even if all safety notes and warnings are observed, using the balance bike still entails
unforeseeable risks such as:
The child being distracted due to childish curiosity and interest in their surroundings
Overestimation of the child’s riding ability
Incorrect behaviour by other road users
Unforeseeable road conditions e.g. slipperiness due to black ice
Component breakage or failure due to unforeseeable material defects or material
fatigue.
x Check the balance bike for material defects or fatigue before every ride.
x Have the balance bike checked by your dealer for damage and breakage after a fall
or accident.
Balance bike Proper use
7
4 Proper use
Neither the manufacturer nor the dealer accept any liability for damage caused due to
improper or incorrect use.
Improper use of the balance bike will invalidate the guarantee (see the “Warranty” chapter).
The balance bike is designed for private use in a suitable play area.
The balance bike is designed for private use by children aged 3 years and up on private
property. The maximum gross weight limit is marked on the frame of the balance bike as
well as recorded on the specifications data sheet provided by the dealer, and must not
be exceeded. The balance bike is not considered a cycle for traffic code purposes.
The balance bike is designed for use by a single child on surfaced ground.
The balance bike is not designed for the following accessories to be fitted or used:
Luggage carrier
Child seat
Child trailer
The child may only use the balance bike as described in this user manual. Any other use
is deemed improper and may result in serious injury or property damage.
5 Age rating
Please note: the balance bike is not designed for children under 3 years
of age.
6 Use
This chapter contains information about basic adjustments to the balance bike, and
information about how to put the balance bike into use.
6.1 A note on braking
The balance bike does not have a brake.
x Explain to your child how they can brake and stop safely using their feet.
Balance bikeUse
8
6.2 Helmet
A helmet protects the head in the event of a fall or accident.
x Only allow your child to use the balance bike when they are wearing a suitable
fitted helmet.
x Consult your dealer when choosing a suitable helmet.
x Have your dealer explain how to correctly adjust the helmet.
6.3 Before every ride
WARNING
Excessive wear or loosened screw joints due to movement and
vibration.
Risk of accident and injury!
x Have your dealer show you how to check for excessive wear
or loosened screw joints.
x Check the balance bike according to the inspection
instructions before every ride.
x Only allow your child to use the balance bike if you do not find
any damage.
x Only allow your child to use the balance bike if there is no
excessive wear and all screw joints are tight.
x Check the balance bike for damage and excessive wear before every ride
(see the “Use / Inspection instructions” chapter).
x Regularly check your child’s seating position and have adjustments made by your
dealer if necessary.
Balance bike Use
9
6.4 Inspection instructions
The inspection instructions assume that all the contents of the user manual have been
read, understood and observed.
x Check the condition of the frame and all components.
x Check all components for deformation, cracks and discolouration.
x Check whether all components are correctly fastened and aligned.
x Check safety elements such as protective caps for damage.
x Your child may only use the balance bike once you have identified all the
components as being functional.
x If you find a non-functional component, have it repaired by your dealer.
6.5 Before the first ride
WARNING
Component or balance bike failure due to changes in the spokes
or screw joints after the first few kilometres.
Risk of accident and injury!
x Have the balance bike serviced regularly by your dealer
.
Observe the specified inspection intervals.
The balance bike has been fully assembled and adjusted by the dealer, and is ready to
ride. Notes on inspection intervals can be found in the “Maintenance” chapter.
Adjustment by the dealer is part of the warranty (see the “Warranty” chapter).
x Familiarise yourself with the balance bike before your child uses it.
x Explain to your child how to use the balance bike.
x Practice with your child how to mount and dismount.
x Have your child practice braking with their feet at low speed (see the “Use / A note
on braking” chapter).
Balance bikeBasic adjustments
10
6.6 After a fall
WARNING
Damage to components due to a fall.
Risk of accident and injury!
x Do not straighten deformed components.
x Have deformed or damaged components replaced by your
dealer immediately.
x If you find or suspect that the balance bike is damaged, do
not use it.
x Check all components after minor falls, e.g. when the balance bike has fallen over
(see the “Maintenance” chapter).
x Have damage repaired by your dealer.
7 Basic adjustments
WARNING
Material breakage or component damage due to a lack of
knowledge when making adjustments.
Risk of accident and injury!
x Have balance bike components adjusted by your dealer.
x Do not make any adjustments to balance bike components if
you lack the necessary expertise and the tools required.
Balance bike Basic adjustments
11
WARNING
Material fatigue and material breakage due to tightening screw
joints incorrectly.
Risk of accident and injury!
x Have your dealer tighten loose screw joints.
x Loose screw joints must be properly tightened to the correct
torque using a torque wrench.
The dealer will fully assemble the balance bike and adjust the saddle to your child’s height.
x When you receive the balance bike, check whether your child can ride it
comfortably and safely, and that the adjustments fit your child.
x If you lack the necessary expertise and the tools required, have adjustments
carried out by your dealer.
x If you make adjustments yourself, ask your dealer about the applicable torques
and use a torque wrench.
x If you make adjustments yourself, check them properly and thoroughly before
you allow your child to use the balance bike.
7.1 Adjusting the saddle
WARNING
Material breakage or damage to the seat post due to a lack of
knowledge when making adjustments.
Risk of accident and injury!
x Have the seat post adjusted by your dealer.
x Do not adjust the seat post yourself if you lack the necessary
expertise and the tools required.
x If you adjust the seat post yourself, ensure that the marking
on the post is not visible.
The saddle height must be adjusted so that the balance bike is adapted to suit the size
of the child.
Balance bikeBasic adjustments
12
1. Loosen the bolt in the seat post clamp
until the seat post can be moved.
2. Adjust the saddle height so that your
child can put both feet flat on the
ground when sitting on the saddle.
3. Make sure that the marking on the seat
post is not visible (see “Illustr.: Seat post
marking”).
4. Twist the saddle so that the frame and
saddle form a straight line.
5. Tighten the bolt, observing applicable
torques (see the “Basics / Notes on
torques” chapter).
7.2 Checking and adjusting the tyre pressure
WARNING
Tyre blow-out or damage due to incorrect tyre pressure.
Risk of damage!
x Use a pump with a pressure display to inflate the tyres.
x Only inflate the tyres to the permitted tyre pressure.
x Do not allow your child to ride with damaged, cracked or
excessively worn tyres.
x Have your dealer explain how to check and adjust the tyre
pressure if necessary.
The tyre pressure is crucial to the rolling resistance and suspension of the balance bike.
Tyre pressure figures may be given in psi (pounds per square inch), kPa
(kilopascals) or bar, depending on the manufacturer.
Illustr.: Seat post marking (example)
Balance bike Basic adjustments
13
1. Read the maximum permitted tyre pressure on the sidewall of the balance bike tyre
(see “Illustr.: Tyre with tyre size specification”).
Illustr.: Tyre with tyre size specification (example)
1
2
X
2
¼
4
0
p
s
i
2
8
0
k
P
a
2
,
8
B
a
r
2. To adjust the tyre pressure or inflate the tyre, unscrew the protective cap from the
valve.
3. Place an air pressure gauge or a pump with a pressure display onto the valve and
read off the tyre pressure.
x If the tyre pressure is too low, inflate the tyre with a pump.
x If the tyre pressure is too high, let air out of the tyre
(see the “Basic adjustments / Reducing the tyre pressure” chapter).
4. Choose a tyre pressure that is suitable for your child’s weight, up to the upper limit
specified on the tyre.
5. Screw the protective cap hand-tight onto the valve after adjusting the tyre
pressure.
6. After adjusting the tyre pressure, check whether the lower knurled nut is firmly in
place and hand-tighten if necessary.
7.3 Reducing the tyre pressure
The tyre pressure can be reduced by letting air out of the inner tube via the valve.
x To reduce the tyre pressure, remove the protective cap and open the valve until air
escapes.
x Close the valve after reducing the tyre pressure and hand-tighten the protective
cap.
Balance bikeCleaning
14
8 Cleaning
8.1 Cleaning products required
The following can be used for cleaning the balance bike:
Clean cloths
Mild, lukewarm soapy water
A soft cleaning sponge or a cleaning cloth
A soft brush
Care products and preservers
x Consult your dealer about suitable care products and preservers.
8.2 Cleaning the balance bike
WARNING
Insufficient knowledge or ability.
Risk of accident and injury!
x Do not allow the children’s bike to be used by children with
reduced physical, sensory or mental capabilities or with a lack
of experience and expertise.
x Do not allow children to carry out cleaning, care and
maintenance alone.
CAUTION
Pinching and crushing of body parts due to lack of knowledge or
incorrect behaviour during cleaning.
Risk of injury!
x Ensure that you keep your fingers and hands away from
moving components.
x Ensure that your fingers and hands do not get caught.
Balance bike Maintenance
15
NOTE
Cleaning the balance bike incorrectly.
Risk of damage!
x Do not use abrasive cleaning products.
x Do not use running water.
x Do not use sharp or metallic cleaning tools.
x Do not use a high-pressure washer or electrical cleaning
devices.
The following points must be noted with regard to cleaning the balance bike:
x Clean the balance bike regularly, even if it is only slightly dirty.
x Wipe all surfaces and components with a damp cloth.
x Use mild soapy water to moisten the cloth.
x Wipe all surfaces and components dry after cleaning.
x Preserve all paintwork and metallic surfaces on the frame at least every six months.
x Contact your dealer if you have any questions about suitable cleaning products.
9 Maintenance
WARNING
Malfunctioning components due to incorrect or inadequate
maintenance.
Risk of injury!
x Only carry out maintenance yourself if you have the necessary
expertise and the tools required.
x Have the balance bike maintained by your dealer at least once
a year.
Balance bikeMaintenance
16
WARNING
Material fatigue and material breakage due to tightening screw
joints incorrectly.
Risk of accident and injury!
x Have your dealer tighten loose screw joints.
x Loose screw joints must be properly tightened to the correct
torque using a torque wrench.
CAUTION
Pinching and crushing of body parts due to lack of knowledge or
incorrect behaviour during maintenance.
Risk of injury!
x Ensure that you keep your fingers away from moving
components.
x Ensure that your fingers do not get caught.
x Wear protective gloves.
The balance bike must be serviced regularly.
x Carry out the following maintenance once a month or after a fall.
x If you find any damage during maintenance, do not allow your child to continue
using the balance bike and have the bike checked or repaired by your dealer.
x Have your dealer document all maintenance and repairs that they carry out.
x If you carry out maintenance work yourself, ask your dealer about the applicable
torques and use a torque wrench.
x If you carry out maintenance work yourself, check the balance bike thoroughly after
the maintenance before you allow your child to use the bike.
Balance bike Maintenance
17
9�1 Inspection intervals
x Have your dealer inspect the balance bike at the following intervals:
Inspection intervals
Inspection Hours of operation Duration of use
1st inspection after 15 hours of operation* or after 3 months*
2nd inspection after 100 hours of operation* or after one year*
Each subsequent
inspection
after a further 100 hours of
operation* or
after a further year*
* whichever is the earliest
Please note that in the event of guarantee claims, Winora-Staiger GmbH reserves the
right to check whether the fault which occurred could have been avoided through proper
maintenance. Depending on the result, we reserve the right to reject the guarantee claim
if necessary.
Your balance bike has a variety of parts that require particular attention, especially with
regard to their exposure to dirt, dust or moisture, or simply because of their relevance to
safety. It is therefore in your own interest to observe the inspection intervals.
9�2 Checking the screw joints
x Lift the balance bike around 5 cm and carefully let it bounce on the ground. Listen
for unusual noises.
x If you hear unusual noises, tighten the relevant screw joints
(see the “Basics / Notes on torques” chapter).
x Have loose screw joints tightened by your dealer if you lack the necessary
expertise or the tools required.
9�3 Checking the frame and front fork
x Check the frame and front fork for deformation, cracks or discolouration
(visual inspection).
x If the frame or the front fork is deformed, cracked or discoloured, have it
checked by your dealer immediately and do not allow your child to ride the
balance bike.
Balance bikeMaintenance
18
9�4 Checking the saddle
x Check whether the saddle can be twisted.
x If you can twist the saddle, adjust the seat post clamp
(see the “Basic adjustments / Adjusting the saddle” chapter).
9�5 Checking the handlebars
x Check whether the handlebars are aligned perpendicularly to the front wheel
(see “Illustr.: Correct handlebar alignment”).
x Have the handlebars adjusted by your dealer if they are not perpendicular to
the front wheel.
Illustr.: Correct handlebar alignment (example)
x Fix the front wheel in place to prevent it twisting sideways, by placing it in a bike rack
for example, and check whether the handlebars can be turned relative to the
front
wheel
.
x If you can twist the handlebars, have them or the handlebar stem adjusted by
your dealer.
x Check whether the handlebars can be moved up and down.
x If you detect play in the head tube or handlebars when pulling the handlebars
up and down, have the head tube or handlebars adjusted by your dealer.
x Check the handlebars and handlebar stem for cracks, deformation or
discolouration (visual inspection).
x If the handlebars or handlebar stem are cracked, deformed or discoloured,
have them checked by your dealer immediately and do not allow your child to
ride the balance bike.
Balance bike Maintenance
19
9�6 Checking the front wheel and rear wheel
1. Hold the balance bike firmly by the front fork or frame.
2. Try to move the front or rear wheel sideways. Check whether the wheel nuts move
as you do so.
x If the wheel nuts move, tighten them (see the “Basics / Notes on torques” chapter).
3. Lift the balance bike and turn the front or rear wheel. Check whether the front or
rear wheel swings sideways or outwards.
x If the front or rear wheel swings sideways or outwards,
do not use the balance
bike and have the wheel checked by your dealer.
9�7 Checking the rims and spokes
1. Check the front and rear rims for cracks, deformation or discolouration (visual
inspection).
x If a rim is cracked, deformed or discoloured, do not allow your child to ride the
balance bike.
2. Squeeze the spokes together gently with your thumb and fingers, checking
whether the tension is the same for all spokes.
x If the tension varies or spokes are loose, have the spokes tensioned by your
dealer.
Alternatively, you can run a wooden or plastic rod across the spokes and
listen for differences in sound.
9�8 Checking the tyres
1. Check whether the tyre pressure is correct (see the “Basic adjustments / Checking
and adjusting the tyre pressure” chapter).
2. Check the tyres for cracks and damage from foreign bodies.
3. Check whether you can clearly feel the tyre tread.
x If a tyre is cracked or damaged, or the tread depth is too low, have the tyre
replaced by your dealer and do not let your child ride the balance bike.
4. Check whether the valves are firmly in place and hand-tighten the lower knurled
nut if necessary by turning it clockwise.
5. Check whether the valves have a protective cap.
x If the protective cap is missing, replace it.
Balance bikeStorage
20
9�9 Checking the safety elements
x Check that the safety elements, such as protective caps over nuts or on the
handlebars, are in place and undamaged.
x If safety elements are missing or damaged, have them replaced by your dealer.
10 Storage
If the balance bike will not be used for a prolonged period, the following points must be
noted with regard to storage:
x Clean the balance bike (see the “Cleaning” chapter).
x Store the
balance bike
in a dry, frost-free place where it is protected against major
fluctuations in temperature.
x To prevent tyre deformation, store the balance bike hanging by its frame.
11 Warranty
Over and above the statutory guarantee, Winora-Staiger GmbH/Haibike USA also
provides a warranty for the cycle frame. The warranty periods are as follows for models
from 2017 onwards, starting on the date of purchase by the original buyer
for aluminium frames: 5 years
for carbon frames: 5 years
for full-suspension frames (excluding bearings and dampers): 5 years
The warranty only applies to the original purchase of the cycle. Proof of purchase,
together with the completed cycle passport and handover certificate, must be submitted
when making a warranty claim.
The warranty only covers frame damage relating to quality, durability and freedom
from defects. Shipping and return costs for the defective frame, labour costs involved
in replacing a defective frame for a new one, and consequential costs resulting from a
defective frame are not covered by the warranty.
The warranty likewise excludes all damage resulting from insufficient care and
maintenance, excessive wear, accidents, cycle overloading, components fitted
incorrectly, and cycle alterations through the attachment and modification of additional
components. The warranty also does not apply if the cycle is used for improper sports
activities, such as performing jumps for which the cycle category was not intended, in
the event of any other type of overuse, and in cases where recommendations contained
in our original operating manual or made by our dealer are disregarded. Please refer to
the original operating manual for full details regarding proper handling of the frame.
Balance bike Guarantee
21
This warranty does not affect any further claims which you may be entitled to make
against the dealer under the statutory guarantee, such as your right to a discount, return
or compensation. The warranty and guarantee rights coexist. This warranty will expire
and not restart in the event that a frame is replaced under warranty.
When purchasing your cycle, you entered into a contract with your dealer. Claims under
this warranty or any other problems must be addressed exclusively to the dealer from
whom you purchased your cycle. To ensure these are handled smoothly, full proof of
purchase and cycle documents must always be submitted. The dealer will then contact
us for further action if necessary.
Should you authorise another dealer to submit a claim, further costs may be incurred as
a result. These costs are your own responsibility and will not be covered by us.
Winora-Staiger GmbH/Haibike USA reserves the right to charge a handling fee for
unjustified complaints.
12 Guarantee
Acquaint yourself with the national and regional guarantee regulations in your country.
The signed handover certificate and proof of purchase must be submitted in the event of
any guarantee claim. Keep hold of these documents.
The guarantee does not apply to damage caused by improper use, force majeure,
operational wear (tyres, wheels, paintwork or lamps, for example) or accidents.
13 Disposal
This chapter contains notes on environmentally friendly disposal, by way of example.
Acquaint yourself with the national and regional regulations in your country.
13.1 Balance bike
Do not dispose of your balance bike in household waste. Take it to a municipal collection
point or a recycling centre.
Alternatively, there are also collections organised by local councils and private
organisations. Contact your local council about this or refer to postal information.
13.2 Packaging
The packaging used to protect your cycle during shipping, called transport packaging,
can generally be left with your dealer. All other types of packaging must be sorted and
disposed of separately. Dispose of cardboard along with waste paper and film in your
recycling collection, or ask your dealer about disposal.
Balance bikeDeclaration of conformity
22
13.3 Tyres and inner tubes
Tyres and inner tubes must not be disposed of in household waste.
Ask your dealer whether they take care of collection and disposal, or take these items to
a recycling centre or municipal collection point.
13.4 Lubricants and care products
Do not dispose of lubricants and care products in household waste, into the sewer
system or into the environment. They must be taken to a hazardous waste collection
point.
Also follow the notes included on the packaging of such products.
14 Declaration of conformity
The declaration of conformity is enclosed with a separate user manual for the balance
bike. With the declaration of conformity, the manufacturer of your balance bike confirms
that the product meets all requirements and other relevant provisions in standard EN 71
and directive 2009/48/EC.
Glossary
Glossary
Term in this original
operating manual
Replaces the following
term (based on official
standards)*
Explanatory/alternative
name
Aero handlebars Aerodynamic extension
(DIN EN ISO 4210-1)
Triathlon handlebars, time
trial handlebars
Fork ends Front fork ends
(DIN EN 15532)
Schrader valve (SV) Schrader valve
(DIN EN 15532)
American valve
Brake pad Brake block (DIN EN 15532)
Brake force modulator Brake force modulator (DIN
EN ISO 4210-2)
Power modulator
Brake cable Inner cable (DIN EN 15532
and DIN EN ISO 4210-2)
Cycle Bikes, racing bikes,
pedelecs, S-pedelecs,
children’s bikes and
balance bikes are referred
to collectively as cycles.
Cycle passport (see cycle) Bike passport
Pinch point Place where body parts or
items of clothing can get
caught
Reaction arm Brake arm (DIN EN 15532)
Guarantee Liability for material defects
Helmet Bike helmet
(DIN EN ISO 4210-2),
suitable helmet (S-pedelec)
Bike helmets and helmets
that are suitable for riding a
pedelec/S-pedelec.
Glossary
Term in this original
operating manual
Replaces the following
term (based on official
standards)*
Explanatory/alternative
name
Chainring Chainwheel
(DIN EN 15532)
Balance bike Toy bike (EN 71)
MTB MTB all-terrain bike
(mountain bike)
Pedelec EPAC (DIN EN 15194) EPAC, e-bike, pedelec 25,
electric bike
Belt Drive belt
(DIN EN ISO 4210-1)
Seat post Seat pillar
Shift cable Cable (DIN EN 15532)
Pulley Drive pulley
(DIN EN ISO 4210-1)
Rear lamp Rear light
Screw joint Bolted joint
(DIN EN ISO 4210-1)
S-pedelec L1e directive 2002/24/EC or
L1e-B regulation 168/2013
S-EPAC, speed e-bike,
pedelec 45
Dunlop valve (DV) Woods valve
(DIN EN 15532)
English or Dutch valve
Luggage system carrier Luggage carrier
(DIN EN 15532)
*Basis: European standards
Individual cycle characteristics
Frame number: Key number:
VIN if applicable (S-pedelec vehicle identification number, EU):
Other
Fitting child seats: () permitted () not permitted
Fitting bike trailers: () permitted () not permitted
Cycle meets national road regulations: () Yes () No
Other remarks (deviations from standard equipment, accessories, defects, etc.):
Cycle condition
() new
() used,
distance travelled in km/mi:
Age:
Handover certificate
The cycle has been delivered complete, together with the following:
(cross or enter number as appropriate)
() Rechargeable battery key (pedelec) () Bike lock key (if different)
()
Winora Group / Haibike USA standard manual with reference to the complete online manual
() If applicable, pedelec drive system quick-start guide with reference to the complete
online manual
() If applicable, S-pedelec drive system manual
() All features of the cycle have been explained
() The cycle has been delivered ready to ride
() The cycle has been delivered pre-assembled, with instructions given on making it
ready to ride
() The data sheet containing the technical specifications for the cycle has been supplied
Purchase or delivery date: Purchase price:
Buyer
First and last name:
Address:
Email: Tel.:
Cycle passport and handover certificate
Location, date (dealer) Location, date (buyer)
1st inspection
300 km / 190 mi / 15 hours of operation /
3 months
Job no.:
Remark:
Date, dealer stamp and signature
2nd inspection
2,000 km / 1,250 mi / 100 hours of
operation / 1 year
Job no.:
Remark:
Date, dealer stamp and signature
3rd inspection
4,000 km / 2,500 mi / 200 hours of
operation / 2years
Job no.:
Remark:
Date, dealer stamp and signature
4th inspection
6,000 km / 3,750 mi / 300 hours of
operation / 3years
Job no.:
Remark:
Date, dealer stamp and signature
5th inspection
8,000 km / 5,000 mi / 400 hours of
operation / 4years
Job no.:
Remark:
Date, dealer stamp and signature
6th inspection
10,000 km / 6,250 mi / 500 hours of
operation / 5years
Job no.:
Remark:
Date, dealer stamp and signature
Inspection intervals
Winora Group original operating manual/Haibike USA original operating manual
LANGUAGE: ENGLISH
EDITION: 1 | 07/2016
Copyright
The text, images and information in these documents are protected under the
copyright of Winora-Staiger GmbH/Haibike USA.
No translation, reprinting, reproduction or other commercial use such as on
electronic media, even in part, is permitted without prior written consent from
Winora-Staiger GmbH.
WINORA GROUP | Winora-Staiger GmbH
Max-Planck-Straße 6
97526 Sennfeld (Germany)
Tel. +49 (0) 9721 6501-0
Fax +49 (0) 9721 6501-45
info@winora-group.de
www.winora-group.de
USA | Haibike USA
2685 Park Center Dr, Unit C
Simi Valley, CA 93065 – USA
EBCC Technical and Customer Center
Tel. +1 800-377-4532
ACCELL North America
info@haibikeusa.com
www.haibike.com
Europe
USA
224


Need help? Post your question in this forum.

Forumrules
1

Forum

haibike-trekking
  • How do you switch the lights of on the trekking 10. Trevor@woldsweather.co.uk Submitted on 21-8-2023 at 22:51

    Reply Report abuse
  • How do I switch the lights off on the Trekking 10? Submitted on 21-8-2023 at 22:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for HAIBIKE Trekking at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of HAIBIKE Trekking in the language / languages: English as an attachment in your email.

The manual is 31,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of HAIBIKE Trekking

HAIBIKE Trekking User Manual - German - 272 pages

HAIBIKE Trekking User Manual - Dutch - 266 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info