564790
15
Zoom out
Zoom in
Previous page
1/34
Next page
15
8.6. Cleaning the flue gas passes and the flue
tubes
Normally it is sufficient to clean the flue gas passes and
the flue tubes once a year. First pull the stove away from
the wall so as to create enough room to work at the
back.
To clean the flue gas passes, proceed as follows:
Disconnect the
flue baffle (1)
from the guide
by lifting it. Draw
the right
cladding (2)
down out of the
guide and place
it down in the
ash space. Then
the flue baffle
can be removed
and the upper
part of the
combustion
chamber can be
cleaned. (See
Figure 8a).
Figure 8a: Removing the flue baffle
Then remove the right side wall. This is fixed with
screws (1) at the back and at the front with 3 connectors.
Remove the
screws from
the back and
pull the side
wall off
sideways.
(See Figure
8b).
Figure 8b: Removing the side wall
Undo the screws and remove both the covers of the
openings. Now you can clean the exposed insides of the
flue gas passes. (See Figure 8 c+d).
After completion of the cleaning make sure that
when putting back the covers, the seals are seated
in the right positions. It is essential to replace
defective seals.
Figure 8c: Cleaning covers
Figure 8d: Cleaning covers open
8.7. Cleaning the induced draught housing and fan
This housing is made accessible for cleaning by undoing
the 4 nuts shown in Figure 9. (See arrows).
Remove the induced draught motor by pulling it out.
Now clean the flue gas passes, the induced draught fan
and the flue tubes with a brush and an ash vacuum
cleaner.
Then reassemble the components in reverse order.
Make sure that the seal is seated in the right position
again. It is essential to replace defective seals.
Make sure of the electrical connections on the fan motor
and their correct positions.
Figure 9: Induced draught fan
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn PELLETTO 432.08 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn PELLETTO 432.08 in the language / languages: English as an attachment in your email.

The manual is 3.08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn PELLETTO 432.08

Haas-Sohn PELLETTO 432.08 Usermanual and installation guide - German - 34 pages

Haas-Sohn PELLETTO 432.08 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info