564781
18
Zoom out
Zoom in
Previous page
1/33
Next page
18
Figure 13: Stainless steel ignition
9.5. Control unit
The microprocessor control unit ensures safe,
automatic operation of the pellet stove. The control unit
controls the interaction of the components e.g. induced
draught fan, screw conveyor motor, flame temperature
sensor, room temperature sensor etc..
The pellet stove’s electrical fuses are incorporated into
the control unit.
To change these fuses you must remove the left side
wall.
Figure 14:
1. Screw conveyor motor
2. Condenser, screw conveyor motor
3. Fuse T 0,315A
4. Fuses T 3,15A
5. Backup battery
9.6. Operator console
Figure 15: Operator console
9.6..1 Backlighting
The backlighting of the display is switched off 5
minutes after the operator console was last
operated.
9.6..2 Activating the backlighting
The backlighting is switched on by pressing any
key. It is only after the backlighting is activated that
the function keys are active.
The backlighting is also activated by any error
message generated.
9.7. Induced draught fan with rotation speed
feedback
The induced draught fan generates low pressure in
the combustion chamber and thereby supplies the
required volume of air for combustion to the
combustion chamber or through the combustion
pot.
The induced draught fan is equipped with rotation
speed feedback. This permits detection of any
difference between the target and actual operating
status and countermeasures to be taken or, in the
case of greater differences, permits the stove to be
shut down (safety shutdown).
9.8. Flame or combustion chamber temperature
sensor (combustion chamber thermosensor)
The flame temperature is measured in “Heating
mode” operating mode.
The flame temperature measured is an indicator of
the energy level in the grate and hence the basis of
2
1
4
5
4
3
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn PALLAZZA-II 534.08 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn PALLAZZA-II 534.08 in the language / languages: English as an attachment in your email.

The manual is 4.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn PALLAZZA-II 534.08

Haas-Sohn PALLAZZA-II 534.08 Usermanual and installation guide - German - 34 pages

Haas-Sohn PALLAZZA-II 534.08 User Manual - French - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info