812049
14
Zoom out
Zoom in
Previous page
1/36
Next page
14
Cleaning the combustion pot may only be done
with a cooled down stove in “OFFoperating mode.
Otherwise there is a risk of burns!
To this end the combustion pot must be removed from
the stove. Once the combustion pot has been removed,
any residual ash that is in the stove underneath the
combustion pot must also be removed.
After cleaning, the combustion pot is to be put back into
the right position in the burner seat. Check the correct
seating of the combustion pot again so as to avoid poor
seals.
A visual check of the dirt on the burner and the
combustion chamber for combustion residues must
be carried out by the operator at regular intervals!!!
Figure 5: Burner dirty
Figure 6: Burner clean
The cleaning intervals for the combustion pot and the
glass panel depend directly on the quality of the wood
pellets (high ash content) and may vary between a few
hours of combustion and several days.
8.4. Removing the ash from the combustion
chamber
To thoroughly clean the ash out of the combustion pot
and the combustion chamber, the pellet stove must be in
a cooled down condition and in the OFF operating
mode.
Procedure:
Press the left key on the operator console repeatedly
until the Info screen appears then press the right key
(Menu) with the two middle keys move the cursor to
Operating Modes press the right key (Select) with
the two middle keys move the cursor to OFF press the
right key (Save) - the stove begins to cool down.
Once the stove has completely cooled down, cleaning
work can begin.
Attention!!
The stove’s Cooling down programme is ended after
about 15 minutes. The stove may still be hot after
the end of the cooling down phase.
Do not start cleaning until the stove is completely
cooled down! “Risk of burns!
The frequency of ash removal depends directly on the
quality of the wood pellets used. We recommend
removing the ash from the combustion chamber with an
ash vacuum cleaner.
8.5. Cleaning the pellet container
Heat the pellet stove until the storage tank is completely
empty. Then the protective grille (2) in the pellet tank
may be removed. Then clean the tank and the intake of
the screw conveyor housing with a vacuum cleaner.
After cleaning, it is essential to put back the protective
grille. When doing this, make sure that no screws fall
into the pellet tank so as to avoid consequential damage
to the screw conveyor.
Figure 7: Pellet tank
with protective grille (1)
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn PALLAZZA 532.08 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn PALLAZZA 532.08 in the language / languages: English as an attachment in your email.

The manual is 4.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn PALLAZZA 532.08

Haas-Sohn PALLAZZA 532.08 User Manual - German - 36 pages

Haas-Sohn PALLAZZA 532.08 User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info