812048
13
Zoom out
Zoom in
Previous page
1/36
Next page
13
between the relevant switch on and switch off
times.
After the completion of the day of the week
programming, the programming window for this
day of the week can be saved and quitted by
pressing the left key (Back).
The other days of the week must be
programmed in the same way.
7.3..3.4 Example of programming for “Monday”
Press the left key repeatedly until the Info
screen appears.
Then press the middle bottom key.
Now the screen in which the days of the week
can be selected appears.
Move the cursor with the two middle keys so
that the MO field (MO means Monday) is
highlighted with the cursor.
Then press the right key (Edit).
Now the programming window for “Monday”
appears
The first column contains position numbers 1, 2
and 3
In the second column, the switch on times
(marked by the letter E) are programmed in 15
minute jumps with the two middle keys.
o You can move from the left column to
the right with the right key (arrow).
In the third column, the switch off times (marked
by the letter A) are programmed in 15 minute
jumps with the two middle keys.
In the fourth column, the desired target room
temperature is assigned to the period that falls
between the relevant switch on and off times.
After completion of the programming of the day
of the week, the programming window for this
day of the week can be saved and quitted by
pressing the left key (Back).
8. Cleaning and maintenance work
The functioning of your device depends to a large
extent on regular expert maintenance. Because of the
ash accumulation resulting from the combustion of wood
pellets, constantly recurring cleaning and maintenance
work needs to be carried out. This will permit operation
to be as trouble-free as possible.
The frequency of maintenance in turn depends to a large
extent on the pellet quality (ash content). Quality pellets
have a low ash content of about 0.2-0.3%. However, if
the ash content is higher (0.5% and over), the interval
from maintenance to maintenance is reduced and the
accumulation of ash increases by 2 or 3 times. This
results in lower heat output and an increased fan
rotation speed.
We therefore recommend checking and/or
cleaning the flue gas passes after 1,000 kg of
pellets at the latest. (See Figure 8 a+d).
Attention!
Devices that are not maintained in accordance with
our specifications must not be operated. Failure to
observe this point will invalidate all guarantee
claims.
As soon as you detect ash and clinker deposits in the
cold combustion pot, it must be cleaned. (See Figures 5
+6). If this is not done, the clinker will continue to
accumulate. Then the device will no longer be able to
ignite properly. Pellets can pile up in the combustion pot.
In extreme cases, this can reach all the way back to the
pellet chute. Backfire in the pellet container and
smouldering in the pellet tank might possibly result.
This will destroy your device and is not covered in
your guarantee.
Attention!
Before cleaning work starts, the stove must be
cooled down, the On/Off toggle switch must be in
the “0” position and the mains cable must be
disconnected!
Once the cleaning work is completed, the correct
operating status of the device must be re-
established: Put the combustion pot in correctly,
close the combustion chamber door.
8.1. Cleaning the surface
Dirt on the upper surface of the stove may be cleaned
off with a damp cloth or if necessary with mild soapy
water. You are advised against using corrosive cleaning
agents and solvents since these might damage the
surfaces.
8.2. Cleaning the glass panel
To clean the viewing panel, you must first open the
stove door. Dirt on the glass panel can be removed with
a glass cleaner or with a damp sponge on which you
have sprinkled some of the wood ash present.
(Environmentally friendly).
Cleaning the glass panel may only be done with a
cooled down stove in the OFF operating mode.
8.3. Cleaning the combustion pot
During operation, deposits may form in the combustion
pot. How quickly the combustion pot becomes dirty
depends solely on fuel quality. The deposits or
encrustations must be removed from time to time.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn PALLAZZA 517.08 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn PALLAZZA 517.08 in the language / languages: English as an attachment in your email.

The manual is 4.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn PALLAZZA 517.08

Haas-Sohn PALLAZZA 517.08 User Manual - German - 36 pages

Haas-Sohn PALLAZZA 517.08 User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info