Manual Haas-Sohn KOMFORT-IV (page 6 of 12) (English)

811882

Zoom out

Zoom in

1/12

7.4 Chimney connection:

If the existing chimney does not have a suitable

shaped connection piece for the fireplace insert a

subsequent connection has to be established. The

chimney connection height is obtained from the

correctly placed fireplace insert plus fitted smoke

gas bend and connecting piece, measured from

the upper edge of the support plate to the centre of

the connecting pipe in the inlet area of the

connection point. Please take into account the

necessary distances for primary walling, heat

insulation, expansion joint etc.

7.5 Primary walling and heat insulation of the

back and side walls:

Once a suitable chimney connection piece has

been installed the required primary walling and

heat insulation can be carried out.

7.6 Necessary primary walling and heat insulation:

The required minimum heat insulation in front of components to be protected was established during the

testing of the fireplace inserts Haas + Sohn according to DIN 18895 and EN 13229. The following protective

measures were determined:

Fireplace insert

ESPRIT 185.16 Fireplace

insert Opus

186.18

Fireplace inserts

KOMFORT 180.18,

PRESTIGE 181.18,

EXQUISIT 182.18,

TREND 184.18

Thickness in mm

Back wall 100 100 100

Primary walling Side wall 100 100 100

(Primary walling replacement,

insulating material according

to AGI Q 132)

Room ceiling within

covering 60 60 60

Floor 40 40

Side wall 120 40

Termax

SN 400 120

Back wall 120 40

Termax

SN 400 130

Convection air ceiling

/intermediate ceiling 110 120 120

Heat insulation layer

Flue gas pipe outside the

convection jacket 60 60 60

1. Primary walling: 10 cm thick mineral primary

walling must be erected directly on the building

wall (back wall and if applicable side wall) to

be protected. The primary walling must be

erected up to the insulation layer and the

building wall to be protected, however protrude

at least 20cm over the connecting piece (flue

gas pipe). Primary walling can be omitted if the

building wall is at least 10cm thick and

consists of non-combustible components and

is not a carrying reinforced concrete wall.

2. Room ceiling above the heating insert (primary

walling replacement): If the cavity or the

covering above the fireplace insert reaches up

to the room ceiling this must be protected if it

consists of combustible materials or serves as

a carrying element. The protection consists of

an at least 6 cm (better 10 cm) thick heat

insulation layer (insulating material code

number: 12.07.21.75.11 according to AGI Q

132). This protective measure is

recommended as load-bearing intermediate

ceiling (e.g. of plate) with heat insulation layer

arranged on top.

3. Heat insulation: Convection jacket and

convection hood (external equipment shape)

must be covered with a heat insulation layer

on all sides. The heat insulation must be butt

joined without any gap and installed in an

overlapping arrangement on the sides. If these

insulation panels are not held by walls,

coverings or adjoining panels, these shall be

attached at a distance of approximately 30 cm.

The room-side covering (apron) need not be

heat-insulated if the heating insert design is

such that the free surfaces of the covering and

the surfaces of the recesses for fuel storage

can heat to a maximum of 85°C. In the case

of surfaces of mineral building materials,

except surfaces on which items can be placed,

the value of 85°C is replaced with the value of

120°C. The heat insulation layers of mineral

wool or comparable must be tightly covered

towards the installation room and convection

air room to prevent flying fibres.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn KOMFORT-IV in the language / languages: English as an attachment in your email.

The manual is 0.23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn KOMFORT-IV

Haas-Sohn KOMFORT-IV Installation Guide - German - 12 pages

Haas-Sohn KOMFORT-IV Installation Guide - French - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Haas-Sohn KOMFORT-IV Manual

Product: