564839
12
Zoom out
Zoom in
Previous page
1/13
Next page
General scheme: heating system 1
Protection against overheat in case of electric power failure
with use of a cooling exchanger (loop).
supplement 4
supplement 3
Inlet and reverse piping (Warm water)
Cooling exchanger piping
Cable CYKY 3Cx1,5
Flow direction
Legend:
1. Warm water exchanger
2. .Circulating pump
3. .Expansion tank
4. Heating body
5. .Discharge valve
6. .Safety valve
7. Thermostatic valve ESBE, warm water 25 –
60 °C
8. Ball cock
9. .Closing filter
10. .Pressure gauge
11. Deaerating valve
12. Waste
13. .Cooling exchanger (look)
14. Safety warm water valve
General scheme: heating system 2
Combined heating system : Electric boiler + fireplace
stove , branches A and B, backup UPS 300.
Separating valves – heat circuits I- II:
Designed for separation of the heat circuits A
and B.
Heat circuit B: A part of the heat circuit.
Only for the fireplace stove.
Heat circuit A: General heat circuit. Both
devices in operation at a time.
Instal a thermoregulating valve , e.g .ESBE
TV25, opening temperature 60oC. When this
temperature is reached, the valve opens , and
the liquid from the heat system B (or A+B) is
let in the fireplace stove circuit (3-1).
The
inlets 1 and 3 of the valve are open – to
provide minimum temperature required for the
reverse water.
The recommended temperature gradient is 75-
60 °C. To provide this, the following
conditions must be met:
B – Connection to the parts of the system
A – connection to the general heating system
12
Backup UPS 300
11. Thermostat
10. Deaerating valve
9
Electric boiler
8. Pressure gauge
7. Ball cock
6. Closing valve
5. Safety valve
4. Thermoregulation valve , e.g. ESBE TV25
3
Expansion vessel
2. Circulating pump
1. Fireplace stove and exchanger
LEGEND:
Warm water inlet piping
Warm water reverse piping
A – A)Warm water output
B
B)
Reverse water input
C – Input of cooling water in the cooling exchanger (loop)
D – Cooling water output (into the sewage system)
The cooling exchanger (look) , the protection against
overheat (13), must not be used for other purposes than as
designed!
Connection to cold water system
24
25
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn KALMAR II 11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn KALMAR II 11 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info