Manual Haas-Sohn HSP2.PREMIUM.17 (page 13 of 31) (English)

564777

Zoom out

Zoom in

1/31

8.1. Cleaning the surface

Dirt on the upper surface of the stove may be cleaned

off with a damp cloth or if necessary with mild soapy

water. You are advised against using corrosive cleaning

agents and solvents since these might damage the

surfaces.

8.2. Cleaning the glass panel

To clean the viewing panel, you must first open the

stove door. Dirt on the glass panel can be removed with

a glass cleaner or with a damp sponge on which you

have sprinkled some of the wood ash present.

(Environmentally friendly).

Cleaning the glass panel may only be done with a

cooled down stove in the OFF operating mode.

8.3. Clean combustion chamber” function

instruction

Die The display on the operator console starts flashing.

(The backlighting switches on and off and the “Clean

combustion chamber” instruction appears).

The instruction to clean the combustion chamber refers

not just to the cleaning of the burner but also to the

cleaning of the entire combustion chamber with an ash

vacuum cleaner.

The process of the “Clean combustion chamber”

function looks like this:

The entire combustion chamber is to be cleaned with an

ash vacuum cleaner at intervals of no longer than 30

operating hours.

The process of the “Clean combustion chamber”

function looks like this:

The entire combustion chamber is to be cleaned with an

ash vacuum cleaner at intervals of no longer than 30

operating hours.

However, this instruction to clean the combustion

chamber (display flashing) does not trigger an error

message during Heating mode. But after the display has

started flashing, if the stove switches

back to “Standby” mode, the stove can no longer be

automatically ignited before the combustion chamber

has been cleaned.

To clean the combustion chamber, the stove has to be

switched to “Off” operating status.

If the combustion chamber is now cleaned, then the

“Clean combustion chamber” error message will

thereafter be cleared automatically. A precondition for

the automatic clearance of this error message is that the

combustion chamber door is open for longer than 60

seconds in “Off” operating status. This time is required

for cleaning the combustion chamber including the

burner thoroughly with an ash vacuum cleaner.

If the door is open longer than 60 seconds in “Off”

operating status, then the operating hours counter,

which is responsible for the “Clean combustion

chamber” instruction, is automatically reset to zero.

This reset of the operating hours counter occurs even if

the cleaning of the combustion chamber is performed

before the 30 operating hours have run provided that the

stove is in “Off” operating status and the door is open for

longer than 60 seconds during cleaning.

8.4. Cleaning the combustion pot -weekly

During operation, deposits may form in the combustion

pot. How quickly the combustion pot becomes dirty

depends solely on fuel quality. The deposits or

encrustations must be removed from time to time.

Cleaning the combustion pot may only be done with a

cooled down stove in “OFF” operating mode. Otherwise

there is a risk of burns!

To this end the combustion pot must be removed from

the stove. Once the combustion pot has been removed,

any residual ash that is in the stove underneath the

combustion pot must also be removed.

After cleaning, the combustion pot is to be put back into

the right position in the burner seat. Check the correct

seating of the combustion pot again so as to avoid poor

seals.

Figure 5: Burner dirty

Figure 6: Burner clean

The cleaning intervals for the combustion pot and the

glass panel depend directly on the quality of the wood

pellets (high ash content) and may vary between a few

hours of combustion and several days.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn HSP2.PREMIUM.17 in the language / languages: English as an attachment in your email.

The manual is 7.23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn HSP2.PREMIUM.17

Haas-Sohn HSP2.PREMIUM.17 Usermanual and installation guide - German - 32 pages

Haas-Sohn HSP2.PREMIUM.17 User Manual - French - 33 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Haas-Sohn HSP2.PREMIUM.17 Manual

Product: