811873
26
Zoom out
Zoom in
Previous page
1/32
Next page
GB
22
H. Screw motor defective G. Flame temperature sensor defective -
contact service department
H. Screw motor defective - contact service
department
F0027 A. Burner dirty
B. Burner not lying flush
C. Door not sealed properly
A. Clean burner
B. Position burner correctly
C. Check seal on door
F0028 A. Burner / combustion chamber dirty
B. Flame temperature sensor at bottom
defective
A. Clean burner
B. Contact service department
F0033 A. No WLAN connection
B. WLAN code is incorrect
C. No IP address received
A. Check WLAN reception
B. Check WLAN code
C. Check DHCP settings on the router
F0034 A. No internet connection available A. Check internet connection
F0040 A. Combustion chamber not cleaned in
specified time interval
A. Clean burner and combustion chamber
the combustion chamber door must be opened
in "OFF" operating status. The burner and
combustion chamber are carefully cleaned
using an ash vacuum cleaner. The combustion
chamber door must be opened for longer than
60 seconds here so that the error message is
automatically cleared.
F0041 A. Maintenance interval exceeded A. Clean the flues
F0050 A. The spare battery empty A. Replace the battery of the control system
(CR 2032)
F1000 /
W1000
A. Restart of the hardware A. The device is without to power supply - error
message in the Record of defects
W0042 Information Service interval has been reset
15. General information / faults
Fault: Cause: Correction:
Pellet stove does not
start
1. The set Target room temperature is
lower than the current Actual room
temperature
2. The temperature of the fumes is too
high
3. An error has
4. An error has occurred there is no
allocated time zone in the week
program
1. Increase Target room temperature
2. Let the instrument cool down
3. See error correction, Section 15.1.
4. Adjust week programming, Section
10.1.1.
No display 1. Loose or defective connection cable
between operator console and control
unit
2. Contrast shifted
1. Contact service department
2. Reset contrast
Noise in the (induced)
draught fan
Ashes in the body of the draught fan Remove the ashes using an ash
exhauster
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn HSP 7 Diana Grande-Plus RLU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn HSP 7 Diana Grande-Plus RLU in the language / languages: English as an attachment in your email.

The manual is 1.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn HSP 7 Diana Grande-Plus RLU

Haas-Sohn HSP 7 Diana Grande-Plus RLU User Manual - German - 32 pages

Haas-Sohn HSP 7 Diana Grande-Plus RLU User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info