811864
54
Zoom out
Zoom in
Previous page
1/59
Next page
GB
27
D. Change flue tube pipeline- contact service
department
E. Flue gas temperature sensor defective -
contact service engineer
F0023 A. Flame temperature sensor defective or not
connected
A. Contact service department
F0025 A. Burner dirty (at burner test during start
zone)
B. Leakage
C. Flue draught too low
A. Clean burner tray
B. Check doors, ashtray doors, seals
C. Check the chimney
F0026 A. Pellet tank empty
B. Burner not lying flush
C. Burner dirty
D. Pellet fuel has too low a calorific value
E. Downpipe / screw conveyor blocked
F. Room too airtight required combustion air
cannot flow into the room
G. Flame temperature sensor defective
H. Screw motor defective
A. Fill pellet tank
B. Position burner correctly
C. Check burner/ clean burner
D. Switch to high quality pellet type
E. Clean the intake on the screw conveyor
housing with a vacuum cleaner.
F. Ensure adequate combustion air - Connect
stove with outside air
G. Flame temperature sensor defective -
contact service department
H. Screw motor defective - contact service
department
F0028 A. Burner / combustion chamber dirty
B. Flame temperature sensor at bottom
defective
A. Clean burner
B. Contact service department
F0033 A. No WLAN connection
B. WLAN code is incorrect
C. No IP address received
A. Check WLAN reception
B. Check WLAN code
C. Check DHCP settings on the router
F0034 A. No internet connection available A. Check internet connection
F0040 A. Combustion chamber not cleaned in
specified time interval
A. Clean burner and combustion chamber
the combustion chamber door must be opened
in "OFF" operating status. The burner and
combustion chamber are carefully cleaned
using an ash vacuum cleaner. The combustion
chamber door must be opened for longer than
60 seconds here so that the error message is
automatically cleared.
F0041 A. Maintenance interval exceeded A. Clean the flues
F0043 A. Flame temperature sensor circuit open A. Contact service department
F0050 A. The spare battery empty A. Replace the battery of the control system
(CR 2032)
F0053 A. Open tank door A. Close pellet tank cap
F0060 A. The parameters of factory settings have
been incorrectly loaded
A. Contact service department
F1000 /
W1000
A. Restart of the hardware A. The device is without to power supply - error
message in the Record of defects
W0042 Information Service interval has been reset
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn HSP 4.0-F3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn HSP 4.0-F3 in the language / languages: English as an attachment in your email.

The manual is 5.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Haas-Sohn HSP 4.0-F3

Haas-Sohn HSP 4.0-F3 User Manual - German - 36 pages

Haas-Sohn HSP 4.0-F3 User Manual - French - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info