564869

Haas-Sohn GENF II RUIVONA Manual

2
Zoom out
Zoom in
Previous page
1/10
Next page
10.6. HAAS+SOHN Rukov s.r.o Products and Manufacturing Programme.................................. 17
11. SUPPLEMENTS...............................................................................................................17-19
Congratulations! You have just bought the fireplace insert HAAS + SOHN, a top-quality product.
Thank you very much for your interest and purchase. Kindly read the Manual to find out about the
function, correct use and handling. We recommend you to read the instructions carefully in order to
avoid any risk related to likely damage. Proper operation and maintenance affects the service life of
the product as well. In addition, proper operation and fuel supply is connected with fuel savings and
environment protection. The technical specifications are shown in the Technical Card (included in
the booklet).
The manufacturer provides guarantee providing you adhere to the directions and recommendations
in the instructions for operation and maintenance. Keep the Operating Instructions and the Technical
Card safe to be able to refresh your knowledge at the beginning of the new heating season.
The General Instructions for Operation, Installation and Maintenance are valid for any type of
the fireplace inserts supplied by HAAS + SOHN. The Technical Card provides detailed
technical parameters for the particular type.
1. TECHNICAL SPECIFICATIONS
Fireplace inserts are designed for heating in habitable rooms, recreation buildings, work stations and
other places to provide thermal comfort. A fireplace insert is used as a closed fireplace while the
visual effect - the perception connected with flame - is similar to the sensation of live fire. In
comparison with conventional open fireplace, the insert is characteristic with higher thermic
efficiency. Another advantage of fireplace insert is the high safety level – no danger from flying
brands while flue gases spreading throughout the heated area is limited.
1.1. General requirements on fireplace insert installations
A fireplace insert is either integrated in the fireplace composition or –without casing – may be
installed in another way at the particular position. It is located in the particular interior on request and
specification by the customer or on architect’s design, viewing the concrete arrangements within the
room(s) to be heated. The installation and the connection to the vent must be approved by an
authorised chimney-sweep company ahead of time. It is recommended to give an order for the
installation and lining at a specialist stove-building company. For a basic layout of a single-shell
fireplace insert see Supplement 1.
Caution! Fireplace inserts may be installed only in rooms and positions risk-free in terms of
the position, building conditions and intended use. The walls and the ceiling at the
installation area must be free of electric lines. For the rooms with a fireplace insert installed,
sufficient air supply for the firing process must be provided. The base area – the place of the
installation – must be proper construction and size to allow standard operation of the hearth.
1.2. Heating concept
Fireplace inserts are designed for burning wood, eco-fuel cakes and coal cakes (specific types only)
in a burning-through way, characteristic with very good firing conditions.
The air within the room is heated thus the thermal comfort is provided by heat convection, in part by
heat radiation as well. This way, you can heat up even very cold, long-time unheated rooms very
quickly. The heat convection means that the cooler air sucked- in at the area of the bottom part of
the insert is heated inside the convective area (comprising of double shell of the heating device or its
casing, where the heating process takes place). From there, the heated air is led back in the room
via the holes in the upper part of the casing or the insert. The radiation heat is generated by means
of surface areas of the stove (metal, ceramics, glass). Due to the construction, the biggest radiation
heat source is the glass door.
1.3. Construction design
Fireplace inserts are welded of steel profiles, thickness 2-5 mm. In the middle of the insert, there is a
firing chamber that may be closed with the door (equipped with a self-acting element). The door is
provided with special large-area glass sheet, thermal resistance up to 800 °C.
3 4
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Haas-Sohn GENF II RUIVONA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Haas-Sohn GENF II RUIVONA in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info