701768

H.Koening BOE50 Manual

7
Zoom out
Zoom in
Previous page
1/56
Next page
LCD show s '100', LCD will keep flashing, into boiling water. When Set the boiling water for 100 ℃, the water must be
100 ℃.
In the process of boiling water, press '+' or '-', you can reset the temperature. When set temperature is higher than the
actual water temperature, continue to boil water; When the actual water temperature is up to the set temperature, the
heating tube will not work, and electronic board start the time, about 2 minutes later, LED no display, which means the
kettle back to standby.
When water is finished boiling, the heat pipe stop working, electronic board start timing, about 2 minutes later, LCD no
display, the kettle back to standby. If in 2 minutes, press 'I/O' key, LCD no display, the kettle back to standby. If press
'+' or '-' key, and don’t press 'I/O' again, electronic board start timing, about10 seconds later, LCD without any display.
If press '+' or '-’, and press 'I/O' again, electronic board will reset the work.
2. Insulation functions
Open the lid and full water (not more than the maximum water level 1. 8 L and cannot be less than minimum water
level 0. 8 L), then put on the lid..
Connected the power, the pot body into the power base. Now nothing appear in LCD , which means the kettle is on
standby .When the kettle on standby, only can use the'I/O', you can use '+' and '-' buttons.
Highest heat preservation temperature can only be set at 90 ℃ : when the set temperature and actual water
temperature is higher than 90 ℃, then press ' 'button will not work; When ' ' button has been pressed, and set the
water temperature as 90 ℃, and then press '+' button will not work.
Method 1: firstly, press '+' or '-', LCD show 40℃, then press '+' or '-' button and set heat preservation temperature,
press ' ' keep warm Button, and then press 'I/O' again, LCD and the sign under the LCD on right keep flashing.
The kettle is into the preservation and began to boil water. At this time, if not press 'I/O', LCD and and the dot under
the LCD on right will not flash, after 10 seconds, the LCD no display, kettle back to standby.
Method 2: you can press ' ' , and then press the ' + 'or ' - ' button and set preservation temperature, and then push
the 'I/O' heat preservation, LCD and the sign under the LCD on right keep flashing, The kettle is into the
preservation and began to boil water.
In the process of boiling water, press '+' or '-', can reset the heat preservation temperature. When set temperature is
higher than the actual water temperature, continue to boil water; When the actual water temperature is up to the set
temperature, the heating tube will not work, and electronic board start the time, about 4 hour later, LCD no display,
which means the kettle back to standby. When, after LCD no display, the kettle back to standby mode.
When the boiling water temperature is up to the set temperature, then heat pipes stop working, and the kettle began to
heat preservation.
When the water temperature lower than the set temperature, heat pipes began to heat and up to setting temperature,
and LCD and the sign under the LCD on right keep flashing. When the water temperature is equal to or higher
than the set temperature, the heat pipe does not work, in the insulation state, LCD and the sign under the LCD on
right will not flash, and repeat.
In the process of heat preservation, if press key to exit heat preservation function, return to boil water.
When entered into the state of thermal insulation, electronic board start time, about 4 hour later, the LCD no display,
then the kettle back to standby Within an hour, press 'I/O', LCD no display, the kettle back to standby.
HOW TO CLEAN KETTLE
1. Please unplug the power plug and let the pot become
cool before cleaning.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for H.Koening BOE50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of H.Koening BOE50 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info