Only qualied personnel authorized by the manufacturer should perform the installation of the welding equipment. During set up,
the operator must ensure that the machine is unplugged.
Risk of injury due to moving parts!
The wire feeders contain moving parts that may catch hand, hair, clothes or tools which can lead to injuries! Take extra care.
• Do not place your hand on mobile/pivoting/wire feeding parts of the machine!
• Make sure that all panels remain closed when in use !
DESCRIPTION
The WS4L is a wire feeder suitable for a water cooled torch and designed for use with MIG WS 500. THE WS4R wire feeder is suitable for MIG 400
GR / 500 GR. They work with 200mm reels and 300mm reels.
The unit comes with a swivel support to be mounted on the generator.
DEVICE PRESENTATION (I)
1- Reel support (200 or 300mm)
2- Wire feeder
3- Handle
4- Wire speed potentiometer
5- Euro torch connector
6- Upper section of the swivel support
7- Gas connector of the connecting harness
8- Control cable connector
9- Power cable connector
10- Eye rings (Don’t lift by the handles (3))
ASSEMBLY & CONNECTION (I & II)
Installing the swivel support on the generator
Use the 3 screws (included with the generator) supplied to x the bottom part of the swivel support onto the generator
The upper part of the support is already xed under the wire feeder.
Gas Coupling
Fit the gas pipe to the connector (7) of the wire feeder (collar included)
Contact Cable Connection
Connect the wire feeder to the generator, making sure that the power connectors (9) & (11), the command connectors (8) & (12), and the water
connectors (13) & (14) are securely tightened.
Fix the power cable on the support (15).
WIRE REEL INSTALLATION (III)
• Open the door of the machine.
• Position the reel on to the support (1) taking care of the pin.
• Adjust the break (2), to avoid reel movement tangling the wire when the welding stops.
• Tighten the plastic screw rmly (3).
• For the rst use :
- Release the xing screw of the wire guide (4)
- Put the rollers in place (5). The visible diameter on the roller should be equal to the wire diameter used.
- Place the wire guide (6) as close as possible to the roller but without touching it, then tighten the xing screw.
• To select the adjustment of the drive rollers: loosen the drive roller knob as far as possible (7), insert the wire until it exits the other side by about
2cm. Start the motor by pressing the torch trigger, tighten the knob whilst pressing the trigger. Bend the wire where it comes out of the nozzle and
hold it in place to stop its progress - the setting is correct when the guide roller slides over the wire, even when it is blocked at the end of the torch.
USE
WS-4R / WS-4L allows the user welding using the parameters set on the MIG generator. To adjust the settings to the type and diameter of wire
used, please refer to the 400 GR, 500 GR and 500 WS user manual.
It is possible to change the wire speed, in synergic or manual mode using the potentiometer on the front panel
TROUBLESHOOTING
SymptomsReasonsSolutions
There are sparks between the electrode and the
ller wire.
Metal llings have accumulated on the drive
roller.
Clean the drive roller and the reels with an air-
gun.
Failure to start weldingNo gasGas valve closed or bottle empty
The gas is continuousSolenoid valve blocked or dirtyRemove, check and clean the solenoid valve.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Gys WS-4R at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Gys WS-4R in the language / languages: English, German, French, Spanish as an attachment in your email.
The manual is 2,02 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
