665708
20
Zoom out
Zoom in
Previous page
1/80
Next page
20
TIG 168 / TIG 200 DC
MADE IN FRANCE
EN
Trigger command connector
The trigger command socket is laid out in the following way:
1
4
5
1 2
3
4
5
TIG 200
1- Switch GND + Potentiometer
2- Cold current button
3- Welding torch button
4- Cursor / potentiometer
5- +5V potentiometer 10 KΩ
TIG 168
1- Switch GND
2- Cold current button
3- Welding torch button
REMOTE CONTROL (TIG 200 ONLY)
The remote control operates in TIG and MMA mode.
Connector technology
The TIG 200 is equipped with a female socket for a remote control. The specic 7 point male plug (GYS product
ref.045699) enables connection to a manual remote control (RC) or foot pedal (PEd).
For the cabling lay out, see the diagram below.
D : Switch contact
C : Earth
B : Cursor
A : + 5V
Nb : The Potentiometer value must be 10 KΩ
ref. 045699
Connecting remote/pedal
1- Power up the machine
2- Plug the pedal/remote control to the connecting socket on the machine.
3- The screen will ash and display « No » (Nothing),
4- Select the type of control by turning the intensity adjustment knob:
« No » (Nothing) / « RC » (Remote Control) / « PEd » (Pedal)
5- Turn the knob until the desired selecton is reached, and after 2 seconds the display will freeze on the chosen selec-
tion.
Nb. : In case of error, unplug the remote control, ( « No » will be displayed) and re-start the connection
process.
Remark: You will be asked to specify the remote connected each time the machine is powered up.
Functions
Manual remote control: (GYS product ref.045675)
The remote control enables the variation of current from minimum intensity (DC : 10A / MMA : 10A) to an intensity
dened by the user.
In this conguration, all modes and functions of the machine are accessible and can be set.
Pedal (GYS product ref.045682):
In all modes excluding « Spot » mode, the pedal control enables variation of the current from the minimum intensity
(DC : 10A / MMA : 10) to an intensity denied by the user.
In TIG mode, the machine will only operate in two-stage welding (2T mode). The upslope and downslope are not auto-
matic, and are controlled by the User with the foot pedal.
In « Spot » mode, the pedal control replaces the torch trigger (the pedal position has no effect on the current).
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys TIG 168 DC HF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys TIG 168 DC HF in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info