Only qualied personnel authorized by the manufacturer should perform the installation of the welding equipment. During set up,
the operator must ensure that the machine is unplugged.
Risk of injury due to moving parts!
The wire feeders contain moving parts that may catch hand, hair, clothes or tools which can lead to injuries! Take extra care.
• Do not place your hand on mobile/pivoting/wire feeding parts of the machine!
• Make sure that all panels remain closed when in use !
DESCRIPTION
TF 4R is an air-cooled separate wire feeder for the 3-phase MIG/MAG generators MIG 400G/400 DUO. It accepts 200 and 300 mm wire reels.
The TF 4R is equipped with a swivel support to be xed on the generator.
DEVICE PRESENTATION (I)
1- Reel support (200 or 300mm)
2- Wire feeder
3- Handle
4- Wire speed potentiometer
5- Euro torch connector
6- Lateral torch holder
7- Wheels
8- Upper section of the swivel support
9- Gas connector
10- Control cable connector
11- Power cable connector
12- Black plastic support for the wire feeder
ASSEMBLY & CONNECTION (II)
Installing the swivel support on the generator
The black plastic support for the wire feeder is packed within the wire feeder. Remove the retaining screw then the black plastic support. Use the 3
screws supplied to x the bottom part of the swivel support onto the generator. The upper part of the support is already xed under the wire feeder.
Gas Coupling
Fit the gas pipe to the connectors (12) and (13) located at the back of the generator (pipes and collars not included).
Connection to the generator
Make sure the generator is switched off before performing this operation.
Connect the wire feeder to the generator, making sure that the power and water connectors are securely tightened (11).
WIRE REEL INSTALLATION (III)
• Open the door of the machine et remove the retaining screw (3)
• Position the reel on to the support (1).
• Adjust the reel brake (2) to avoid reel movement tangling the wire when the welding stops. Be careful not to tighten too much - the reel must rotate
without straining the motor.
• Tighten the plastic screw rmly (3).
• For the rst use :
- Release the xing screw of the wire guide (4)
- Put the rollers in place (5). The visible diameter on the roller should be equal to the wire diameter used.
- Place the wire guide (6) as close as possible to the roller but without touching it, then tighten the xing screw.
• To select the adjustment of the drive rollers: loosen the drive roller knob as far as possible (7), insert the wire until it exits the other side by about
2cm. Start the motor by pressing the torch trigger, tighten the knob whilst pressing the trigger. Bend the wire where it comes out of the nozzle and
hold it in place to stop its progress - the setting is correct when the guide roller slides over the wire, even when it is blocked at the end of the torch.
USE
TF 4R allows the user welding using the parameters set on the MIG generator. To adjust the settings to the type and diameter of wire used, please
refer to the generator’s manual.
It is possible to change the wire speed, in synergic or manual mode using the potentiometer on the front panel.
In order to use the separate wire feeder’s torch, press the trigger - the LEDs on the generator’s control panel will start to ash, indicating the
change of torch.
The Speed of the wire feeder is between 1m/min to 20m/min. The maximum gas pressure must not exceed 10 bars (1MPa).
WARNING: The torch connected to the generator (DUO version) must be put on its support before
using the torch connected to the wire feeder. If this advice is not followed, a powerful electrical arc
can occur causing serious injury and damage.
COMPATIBILITY
The wire feeder TF-4R is only compatible with the PROMIG / POWERMIG range. Please refer to the electrical drawing for technical features of the
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Gys TF 4R at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Gys TF 4R in the language / languages: English, German, French, Spanish as an attachment in your email.
The manual is 1,84 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
