665757

Gys T3 GYS AUTO Manual

10
Zoom out
Zoom in
Previous page
1/52
Next page
10
M1 - T1 & M3 - T3 GYS AUTO
EN
SEMI-AUTOMATIC WELDING FOR STEEL/STAINLESS STEEL (MAG MODE)(FIG 3)
These welding can weld 0.6/0.8 and 1.0mm steel and stainless steel wires (g 3A). The device is capable of working
with Ø 0.8 mm steel wire (contact tube Ø 0.8, roller Ø 0.6/0.8 and Ø 0.8/1.0). If you need to use Ø 0.6mm wire, you will
have to change the contact tube, and ensure that the reversible rollers in the wire feeder are posititioned correctly (so
that the writing that states “0.6mm” is visible when in place). For Steel or Stainless Steel, you will need to use specic
gas - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary depending on usage. The gas ow in steel is between 8
and 12L / min depending on the environment and experience of the welder. For the specic requirements, seek advice
from your gas distributor.
SEMI-AUTOMATIC WELDING FOR ALUMINIUM (FIG 3)
These welding can weld 0.8 and 1mm aluminium wires (g 3B).
To weld aluminium, neutral gas “pure argon” (AR) is required. When choosing gas, ask a gas distributor for advice.
The gas ow in aluminium should be between 15 and 25 L / min depending on the environment and experience of the
welder.
Things to note when welding with Aluminium:
-Set the pressure rollers of the wire feeder on the wire at the minimum pressure so as not to pinch the wire
- Remove the capillary tube before connecting the aluminium torch
- When welding aluminium use a special aluminium torch with Teon sheath to reduce friction. Do not cut the sheath
near the connector! It is used to guide the wire from the rollers. (diagram 3-B )
- Contact Tip: Use a contact tip SPECIAL aluminium corresponding to the diameter of the wire.
- Contact Tip: Use the specic Aluminium contact tip corresponding to the diameter of the wire.
SEMI-AUTOMATIC BRAZING WELDING FOR HIGH-TENSILE STRENGTH STEELS
These welding are recommended by car manufacturers to braze-weld high-tensile strength plates with a cuprosilicium
CusI3 wire or cuproaluminium CuAl8 wire (Ø 0.8 mm and Ø 1 mm). The welder must use a neutral gas: pure argon (Ar).
For specic gas requirements, seek advice from your gas distributor. The gas ow required s between 15 and 25 L / min.
GAS CONNECTION (FIG 2)
Connect the manometer (owmeter) to the gas bottle (manometer not supplied with the product).For use with one
or two bottles of gas.
To connect two bottles of gas to three torches, split the pipe into 3 pieces and attach a 3-way “Y” connector. (g 2-C )
To link a single bottle of gas with 3 torches, cut the pipe into 4 pieces and attach two 3-way “Y” connectors.
Connect each bottle to the solenoid valves in the following order:
-T1 solenoid valve to the top left (g 2B:13)
-Spool gun solenoid to the top right (g 2B:17)
-T3 solenoid valve to the bottom (g 2B:16)
To avoid any gas leaks, always use the collars supplied with the product.
PROCESS OF REELS AND TORCHES ASSEMBLY (FIG 4)
Open the device trapdoor.
- Place the reel on the driving pin (g 4:2) of the reel support.
- Adjust the reel brake (g 4:3) to avoid the reel inertia tangling the wire when welding stops. In general, do not tighten
too much!
- The electrical roller (g 4:4) is a double groove roller (0,6/ 0,8 and 0,8/1). The indication on the visible side of the
roller is the diameter in use. For a 0,8 wire, use the 0,8 groove.
- For the rst use:
- Release the xing screw of the wire guide.
To set the adjusting knob of the pressing rollers (g 4:5), proceed as follow: loosen the knob fully, start the motor by
pressing the torch trigger, tighten the adjustment knob whilst pressing the trigger. Bend the wire where it comes out of
the nozzle and hold it in place to stop its progress. The setting is correct when the guide roller slides over the wire even
when it is blocked at the end of the torch. A common adjustment is the rollers command (g 4:5) on the scale 3 for steel
and 2 for aluminium.Nb: for the aluminium wire put a minimum pressure in order not to crush the wire.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys T3 GYS AUTO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys T3 GYS AUTO in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info