665823
37
Zoom out
Zoom in
Previous page
1/50
Next page
37
NEOPULSE 270-T1 / 270-T2 / 300
DE
NUR AUF DIE NEOPULSE 270-T2 / 300
Der Brenner Push Pull (OPTIONAL)
Der Brenner Push Pull wird an den Anschluss (3) angeschlossen. Der Bren-
ners Push Pull ermöglicht die Benutzung von AlSi-Draht , mit Ø 0,8 mm mit
einem 4 m-Brenner (Art.-Nr. 044111).
Der Brenner kann bei allen Modi benutzt werden.
Die Erkennung des Push-Pull Brenners erfolgt durch einfachen Druck auf
die Brennerstaste. Falls Sie eine Push-Pull Brenner mit Potentiometer
benutzen, können Sie auf das Farbdisplay die maximale Schweißwert
einstellen.
Das Potentiometer kann sich zwischen 50 % bis 100 % dieser Schweißwert
ändern.
Schaltplan für Push-Pull Brenner
mit Potentiometer (10 KΩ).
1
3
4
7
8
10
+4
-5
+Pot 10
-Pot 3
R
2
+
-
1 8
M
1
3
2
5
4
Der digitale Brenner wird wie folgend
bedient:
1 - grüne Led (Geschwindigkeit:
)
2 - Drucktaste: Auswahl der Regelung
3 - orange Led (Lichtbogenlänge:
)
4 - Erhöhung (Geschwindigkeit oder Lichtbogen
mit Taste 2)
5 - Verringerung (Geschwindigkeit oder Licht-
bogen mit Taste 2)
NUR AUF DIE NEOPULSE 270-T2
Der Spool Gun Brenner wird an den Anschluss (7) angeschlossen. Er ist nur im
«manuell» oder «synergic»-EASY Modus benutzbar.
- Im «manuell» Modus (s. Seite 32): nur die Drahtgeschwindigkeit ist am Bren-
ner einstellbar (keine Einstellung am Gerät möglich).
Im «synergic» Modus (s. Seite 33): die Taste am Brenner ermöglicht die
Einstellung zwischen 50% und 100% des Wertes auf HIM.
Die Erkennung des Push-Pull Brenners erfolgt durch einfachen Druck auf die
Brennertaste. Achtung, stellen Sie die gewünschte maximale Geschwindigkeit
mit dem Drehregler auf dem Bedienfeld des Brenners ein.
Der Spool Gun Brenner
(OPTIONAL)
Montage der Drahtrolle im
Spool Gun Brenner
4
5
1 2
3
1 - Taste Öffnen/ Schließen der Abdeckung
2 - Schraube für Drahtrolle
3 - Fixierung für Drahtrolle (nicht festziehen)
4 - Stellschraube für Spannung an Drahtvorschubrolle
5 - Potentiometer für Einstellung der Drahtvorschubgeschwindigkeit
- Abdeckung entfernen (1), Schraube entfernen (2).
- Fixierung lösen (3).
- Drahtrolle einlegen.
- Um den Draht in den Antrieb zu führen, drücken Sie den Spannhebel zur Öffnung der
Andruckeinstellung (4)
- Entfernen Sie den Draht aus Brenner.
- Schliessen Sie den Spool Gun-Brenner und den Steuerungsstecker an (s. Seite 2).
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys NEOPULSE 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys NEOPULSE 300 in the language / languages: English, German, French as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info