Manual Gys MONOGYS 200-2CS (page 7 of 44) (English, German, Dutch, French, Italian, Spanish)

665747

Zoom out

Zoom in

1/44

7 / 44

DESCRIPTION

Thank you for choosing our product ! To get the best of your equipment, please read carefully the following.

The 80P, 130P, 160P, 200P are portable, single-phase, air cooled Inverter welding units, for MMA electrode welding

with direct current (DC). They can weld all kind of electrodes : rutile, cast-iron, basic (except for 80P), stainless

steel. (They are over-voltage protected when used on power generators (230 V +- 15%)

POWER SUPPLY – START UP

• This machine is delivered with a 16A plug type EEC7/7. The machine must be plugged on a 230 V (50-60Hz)

socket with earth. The absorbed effective current (I1eff) is shown on the machine, for maximal using

conditions. Check that the power supply and its protection (fuse and/or circuit-breaker) is compatible with the

necessary current during use. In some countries, the change of plug can be necessary to allow a use at

maximal conditions. For the 130P in intensive use, preferably select a 25 A plug. For the 160P in intensive use,

preferably select a 25 A plug. For the 200P in intensive use, preferably select a 32 A plug. The charger must be

installed so that the mains plug is accessible.

• To start the equipment, turn on the potentiometer to the desired current position, the power indicator lights

then. Put the potentiometer on "O" for standby mode.

• Connect the earth clamp and electrode-holder cables in the quick-plugs. Respect the polarities indicated on the

electrode packaging.

•

This Class A equipment is not intended for use in residential locations where the electrical power is provided by

the public low-voltage supply system

There may be potential difficulties in ensuring electromagnetic

compatibility in those locations, due to conducted as well as radiated disturbances.

• These machines are in accordance with the standard EN61000-3-11 if

the maximum permissible system

impedance Zmax at the interface point of the user’s supply

Model 80P 130P 160P 200P

Zmax acceptable 0.34 Ohms 0.34 Ohms 0.34 Ohms 0.25 Ohms

This equipment does not comply with IEC 61000-3-12. If it is connected to a public low voltage

system, it is the responsibility of the installer or user of the equipment to ensure, by

consultation with the distribution network operator if necessary, that the equipment may be

connected.

• Do not use the machine in an area containing metallic conducting dust.

ELECTRODE WELDING (MMA MODE)

• Apply the usual welding rules.

• Leave the machine connected to the supply after welding in order to let it cool down.

• Thermal protection : thermal protection indicator turns on and the cooling time is about 2 to 5 min according

to external temperature.

• Your machine is equipped with 3 specific functions to Inverters :

The Hot Start increases the current at the beginning of the welding.

The Arc Force increases the current in order to avoid the sticking when electrode enters in melted

metal.

The Anti Sticking allows you to easily withdraw your electrode without damaging it in case of sticking.

The machines described have an output characteristic of 'constant current' type. The duty cycle are indicated in

the table below according to EN60974-1 Norm.

X / 60974-1 @ 40°C

(cycle T = 10 min)

80P 130P 160P 200P

I max 6% @ 80 A 5% @ 130 A

14% @ 160 A

20% @ 200 A

60% (cycle T = 10 min) 31 A 45 A 85 A 120 A

100% (cycle T= 10 min) 29 A 40 A 70 A 85 A

Note: the running hot tests have been carried out at atmosphere temperature and duty cycle has been

determined at 40°C by simulation.

TIG WELDING

This machine can be used in TIG mode with a scratch ignition

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gys MONOGYS 200-2CS in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gys MONOGYS 200-2CS Manual

Product: