665718

Gys MASTER 350 Manual

4
Zoom out
Zoom in
Previous page
1/10
Next page
4
MASTER 250-350-450
EN
DESCRIPTION
Thank you for choosing our product! To get the best of your equipment, please read carefully the following.
MASTER welders are traditional stick welders for welding in direct current (DC). They can weld rutile, cast-iron, basic
and stainless steel electrodes. They work on a 380V tri-phase power supply.
Before any use, read carefully the user manual and follow the instructions of the manufacturer. If
the item is misused, it can be dangerous for people, animals and buildings in the working environment.
The user remains responsible for the environment and working safety.
POWER SUPPLY – START UP
• These welders have to be plugged on a 3ph 380V socket (50-60Hz) with EARTH. The absorbed effective current (I1)
is shown on the machine, for maximal using conditions. The machine is tted with a bare power cable. The user has
to connect the three phases and the earth. Check if the power supply and its protection (fuse and/or circuit breaker)
are compatibles with the current necessary. The unit must be located in a place where it is easy to access to the plug.
• Start the machine by turning ON the ON/OFF button.
• Connect the earth cable and the electrode holder in the quick plugs on the front of the machine. Respect the polarities
(+/-) indicated on the electrodes packaging.
• Do not use the machine in a wet environment and in an area containing metallic conducting dust and inammable
elements.
USE
1. Ensure the earth clamp is connected to the work piece (as close as possible to the welding area)
2. Select the welding current by adjusting the knob according to the diameter of the electrode to weld. Adjust the
welding current by turning the knob form 1 to 7.
3. Thermal protection : After a long period of welding or intensive use, it is neFssary to wait until the machine cools
down. These machines are protected by a thermostat which will automatically cut out the power to the unit to prevent
damage during an overload.
4. After using the welding unit, turn off the unit switch and unplug the machine.
MAINTENANCE
• Refer all servicing to qualied personnel.
• Disconnect the generator and wait until the ventilator stopped before working on the unit. Inside the device,
voltages and current are dangerous.
• Two or three times a year, remove the steel cover and blow off the dust with compressed air. Let check the electrical
connections (with an insulated tool) and the insulations by qualied personnel.
• Regularly control the state of the supply cable. If this supply cable is damaged, it must be replaced by the
manufacturer, the after sales service or a qualied technician to avoid any danger.
ADVICE
• Respect welding polarities and currents indicated on the electrode packaging
• Remove the electrode from the electrode holder when you do not use it.
• Keep the ventilated parts of the machine clean to allow in/out air circulation.
SECURITE
The arc welding can be dangerous and leads serious injury, may fatal. Protect yourself and protect the others.
Respect the following warnings:
Arc rays Protect yourself thanks to a welding helmet in compliance with EN175 equipped with
lters in compliance with EN 169 or EN 379. Inform and protect by the same means any
people in the welding environment.
Rain, steam, humidity The working environment must be clean (degree of pollution ≤ 3) and protected against
rain. Put the appliance on an even place and at least at one meter from the parts to be
welded. Do not use in rain or snow.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys MASTER 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys MASTER 350 in the language / languages: English, French, Italian as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info