665818

Gys MAGYS 400 GR Manual

17
Zoom out
Zoom in
Previous page
1/62
Next page
17
MAGYS 400-4 / 400 GR / 500 GR / 500 WS
EN
TROUBLESHOOTING
SYMPTOMS POSSIBLE CAUSES REMEDIES
The welding wire speed is not constant.
Debris is blocking up the opening.
Clean out the contact tip or change it and
replace the anti-adherence product.
Ref.041806
The wire skids in the rollers.
• Check the roller pressure or replace it.
• Wire diameter incompatible with roller
• Covering wire guide in the torch incom-
patible.
The rollers slide over the wire Check and tighten the roller’s screws.
The wire-feeder motor doesn’t operate.
Reel or roller brake too tight. Adjust the brake and rollers.
Electrical supply problem.
Check that the power switch is in the
"On" position.
Bad wire feed.
Covering wire guide dirty or damaged. Clean or replace
Reel brake too tight Adjust the brake
No welding current
Bad connection to the main supply.
Check the mains connection and ensure
the supply is 400 V (3PH).
Bad earth connection.
Check the earth cable (connection and
clamp condition).
Torch trigger inoperative. Check the torch trigger / replace torch
The wire jams (after the rollers)
Guide wire sheath crushed. Check the sheath and torch body.
Wire jammed in the torch Clean or replace.
No capillary tube. Check the presence of capillary tube.
Wire speed too fast Reduce the wire speed
The welding bead is porous
The gas ow rate is not sufcient.
Adjust ow range 15 to 25 L / min.
Clean the work-piece.
Gas bottle empty. Replace
Gas quality unsatisfactory. Replace
Air ow or wind inuence. Prevent drafts, protect welding area.
Gas nozzle dirty. Clean or replace the gas nozzle.
Poor quality wire. Use suitable WIRE for MIG-MAG welding.
Work-piece in bad condition. (rust, etc…) Clean the metal before welding.
The arc produces a lot of sparks
Arc voltage too low or too high. See welding settings.
Bad earth connection.
Check the earth cable (connection and
clamp condition)
Insufcient gas ow. Adjus the gas ow.
No gas ow at the end of the torch. Bad gas connection.
Check that the gas pipe is plugged pro-
perly.
Check the solenoid valve.
When powering on:
The display (9) shows « Err » and the dis-
play (10) shows « 002 ».
At least one of the 3 keys is pressed.
The 3 keys must be released.
When powering on:
The display (9) shows « Err » and the dis-
play (10) shows « 001 ».
The Torch’s trigger is pressed. The trigger must be released.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys MAGYS 400 GR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys MAGYS 400 GR in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info