665818

Gys MAGYS 400 GR Manual

11
Zoom out
Zoom in
Previous page
1/62
Next page
11
MAGYS 400-4 / 400 GR / 500 GR / 500 WS
EN
This manual contains safety and operating instructions. Read it carefully before using the device for the rst time and
keep it in a safe place for future reference.
GENERAL DESCRIPTION
Thank you for choosing this GYS product; please read this instruction manual carefully before installing and using the
product, and keep in a safe place for future reference.
The MAGYS are ventilated semi-automatic welding units (MIG or MAG). Adjustment is quick and easy with their « syner-
gic wire speed » function. They work on a 400V three-phase power supply.
In order to function MAGYS:
• 400 GR requires separate wire feeder WS-4R (ref. 034723) or W5S-4L (ref 032835) and a connection cable.
• 500 GR requires separate wire feeder WS-4R (ref. 034723) or W5S-4L (ref 032835) and a connection cable.
• 500 WS requires separate wire feeder WS-4L (ref. 033573) or W5S-4L (ref 032835) and a connection cable.
ELECTRICITY SUPPLY
The absorbed current (I1eff) is indicated on the device, for use at maximum settings. Check that the power supply and
its protection (fuse and/or circuit breaker) are compatible with the current needed during use.
The device must be placed in such way that the power socket is always accessible.
Do not use an extension cord which has a wire section smaller than 4 mm².
These units are supplied with a 32A plug type EEC7/7. They should be plugged in to a 400 V (3PH) power socket WITH
earth and protected by a circuit breaker (32A and 1 differential 30Ma.)
DEVICE PRESENTATION
Put the rubber mat (only for the Magys 400-4) and the four ring eyes (with their lock washers). The gas bottle needs to
be fastened with 2 chains in the holes at the back of the machine. Attention: Fasten correctly the bottle. You have also
holes to pass a strap on (not included).
1 - On – Off switch 8 - Fastening chains for bottles
2 - Power settings – 2 switches with 9 positions to adjust
the welding voltage output
9 - Reel support Ø 200/300 mm.
3 - Control panel – Welding settings
10 - Gas connector (For the Magys 500 WS, the gas hose
needs to be connected to the owmeter of the bottle).
4 - European standard torch connection
11 - Rear panel for the connection of the separate wire
feeder (Magys 400 GR/500 GR/500 WS)
5 - Power cable (5m) 12 - 5.5 L tank (Magys 500 WS)
6 - Earth cable
13 - Chain xing slot
7 - Gas bottle support (max 1 bottle of 10m3)
SEMI-AUTOMATIC WELDING FOR STEEL / STAINLESS STEEL (MAG MODE) (FIG. 2-A)
The MAGYS units are equipped originally to work on 1mm steel wire (original drive rollers Ø 1/1.2 steel/stainless steel).
Make sure that drive rollers, liner and contact tube are adapted to your wire diameter.
For Steel or Stainless Steel, you will need to use specic gas - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary
depending on usage. The gas ow for steel is between 15 and 25L / min depending on the environment and experience
of the welder.
SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE) (FIG. 2-B)
This welding unit can weld aluminium wires from 1mm.
To weld aluminium, neutral gas “pure Argon” (AR) is required. When choosing gas, ask a gas distributor for advice.
The gas ow in aluminium should be between 20 and 25 L / min depending on the environment and experience of the
welder.
Things to note when welding with Aluminium
- Set the pressure of the rollers to a minimum so as not to crush the wire
- Remove the capillary tube before connecting the aluminium torch
- When welding aluminium use a special aluminium torch with Teon sheath to reduce friction.
Do not cut the sheath near the connector! It is used to guide the wire from the rollers.
(See diagram (16))
- Contact Tip: Use the specic Aluminium contact tip corresponding to the diameter of the wire.
- Drive rollers: Use specic drive rollers to weld with aluminium wire.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys MAGYS 400 GR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys MAGYS 400 GR in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info