665725
28
Zoom out
Zoom in
Previous page
1/56
Next page
28
GYSMI E200 FV
MADE IN FRANCE
ES
Consejos:
Un Hot Start débil para chapas nas, un Hot Start elevado para metales más difíciles de soldar (piezas sucias u oxida-
das).
Para ajustar el Hot Start, siga las etapas siguientes:
Presione la tecla de selección (5).
La inscripción HS (Hot Start) parpadea y luego aparece una cifra.
Ajuste el porcentaje deseado (indicador (1)) mediante los botones (4).
Conrme el valor deseado presionando la tecla de selección (5).
SOLDADURA AL ELECTRODO DE TUNGSTENO BAJO GAS INERTE (MODO TIG)
La soldadura TIG DC requiere una protección gaseosa (Argón).
Para soldar en TIG, siga las etapas siguientes:
1. Conecte la pinza de masa sobre la polaridad positiva (+).
2. Conecte una antorcha con válvula sobre la polaridad negativa (-).
3. Conecte el tubo de gas al manómetro de la botella de gas.
A veces puede ser necesario cortarlo a la altura de la tuerca si este último no se
adapta al manorreductor
4. Seleccione la posición TIG (3) con el seleccionador (5).
(Presione 3 segundos para cambiar del modo TIG al modo MMA)
5. Ajuste la intensidad deseada (indicador (1)) mediante los botones (4), según el
grosor que se va a soldar (30A/mm).
6. Ajuste el caudal de gas con el manómetro de la bombona de gas, y abra la válvula
de la antorcha.
7. Para cebar: tocas el electrodo sobre la pieza a soldar.
8. Al nal de la soldadura: eleve el arco dos veces (arriba-abajo-arriba-abajo) para activar el desvanecimiento automá-
tico (véase la sección de abajo). Este movimiento debe efectuarse en menos de 4 segundos, sobre una altura de 5 a
10mm. Tras ello, cierre la válvula de la antorcha para detener el gas una vez se haya enfriado el electrodo.
Desvanecimiento automático del arco con duración ajustable
Activación de la función:
Esto corresponde, al nal de la soldadura, al tiempo necesario para bajar progresivamente la corriente de soldadura
hasta la parada del arco. Esta función permite evitar suras y cráteres al nal de la soldadura.
Por defecto esta función no está activada (OFF). Para activarla, siga las etapas siguientes:
‘’
Presione sobre el seleccionador (5)
Regule el tiempo de desvanecimiento deseado de 0 a 10 segundos (indicador (1)) mediante las
teclas (4)
Conrme el valor deseado presionando la tecla de selección (5).
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys GYSMI E200 FV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys GYSMI E200 FV in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info