665725
15
Zoom out
Zoom in
Previous page
1/56
Next page
15
GYSMI E200 FV
MADE IN FRANCE
EN
Recommended combinations / Electrode grinding
Current (A)
Ø Electrode (mm)
= Ø wire
(ller metal)
Ø Nozzle (mm)
Flow rate
(Argon L/mn)
0,5-5 10-130 1,6 9,8 6-7
4-8 130-200 2,4 11 7-8
To optimize the working, you have to use an electrode grinded as below:
L = 2,5 x d.
L
d
TROUBLESHOOTING
Anomalies Causes Remedies
MMA-TIG
The device does not deliver any
current and the yellow indicator
lamp of thermal defect (6) lights
up.
The welder thermal protection has
turned on.
Wait for the end of the cooling
time, around 2 minutes. The indi-
cator lamp (7) turns off.
The display is on but the device
does not deliver any current.
The cable of the earth clamp or
electrode holder is not connected
to the welder.
Check the connections.
If, when the unit is on and you put
your hand on the welding unit’s
body, you feel tingling sensation.
The welding unit is not correctly
connected to the earth.
Check the plug and the earth of
your electrical network.
The display is on but the device
does not deliver any current.
The cable of the earth clamp or
electrode holder is not connected
to the welder.
Check the connections.
When starting up,
the display indicates .
The voltage is not included in the
range 230V +/- 15%
Have the electrical installation
checked.
TIG
Instable arc
Default coming from the tungsten
electrode
Use a tungsten electrode with the
adequate size
Use a well prepared tungsten
electrode
Too important gas ow rate Reduce gas ow rate
The tungsten electrode gets
oxidised and tern at the end of
welding.
Welding zone
Protect welding zone against air
ows
Default coming from post-gas or
the gas has been stopped prema-
turely.
Check and tighten all gas connec-
tions. Wait until the electrode cools
down before stopping the gas.
The electrode melts Polarity error
Check that the earth clamp is
really connected to +
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys GYSMI E200 FV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys GYSMI E200 FV in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info