665722

Gys GYSMI 160P Manual

10
Zoom out
Zoom in
Previous page
1/40
Next page
10
GYSMI 80P 130P 160P 200P
MADE IN FRANCE
EN
d. Electrical bonding : consideration shoud be given to bonding all metal objects in the surrounding area. However,
metal objects connected to the workpiece increase the riskof electric shock if the operator touches both these metal
elements and the electrode. It is necessary to insulate the operator from such metal objects.
e. Earthing of the welded part : When the part is not earthed because for electrical safety reasons or because of its
size and its location (which is the case with ship hulls or metallic building structures), the earthing of the part can, in
some cases but not systematically, reduce emissions. It is preferable to avoid the earthing of parts that could increase
the risk of injury to the users or damage other electrical equipments. If necessary, it is appropriate that the earthing
of the part is done directly, but in some countries that do not allow such a direct connection, it is appropriate that the
connection is made with a capacitor selected according to national regulations.
f. Protection and plating : The selective protection and plating of other cables and devices in the area can reduce
perturbation issues. The protection of the entire welding area can be considered for specic situations.
TRANSPORT AND TRANSIT OF THE MACHINE
The machine is equipped with a handle to facilitate transport. Be careful not to underestimate the
machine’s weight. The handle cannot be used to hang the machine from other equipment.
Do not use the cables or torch to lift or move the machine. The welding equipment must be moved in
an upright position.
. Transportation standards are different.
INSTALLATION
Rules to follow:
• Put the machine on the oor (maximum incline of 10°.)
• Ensure the work area has sufcient ventillation for welding, and that there is easy access to the control panel.
• The machine must be placed in a sheltered area away from rain or direct sunlight.
• The machine must not be used in an area with metallic dust.
• The machine benets from an IP21 protection index, which means:
- Protection against acess to dangerous parts from solid bodies of a ≥12.5mm diameter and,
- Protection against vertically falling water droplets
The manufacturer does not incur any responsibility regarding damage to both objects and persons that
result from an incorrect and/or dangerous use of the machine .
MAINTENANCE / RECOMMENDATIONS
• Maintenance should only be carried out by a qualied person.
• Ensure the machine is unplugged, and that the inside fan has stopped before carrying out maintenance work.
Caution - High Voltage and dangerous Current levels can be present inside the machine.
• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the electrical
connections checked by a qualied person, with an insulated tool.
• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be replaced
by the manufacturer, its after sales service or an equally qualied person to prevent danger.
• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.
• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.
• The power cables, extension cords and welding must be fully unwound in order to prevent overheating.
INSTALLATION – PRODUCT OPERATION
Only qualied personnel authorized by the manufacturer should perform the installation of the welding equipment.
During set up, the operator must ensure that the machine is unplugged. Connecting generators in a series or a parallel
circuit is forbidden.
HARDWARE DESCRIPTION
The 80P, 130P, 160P, 200P are Inverter technology based welding machines, portable, single phase, fan cooled, for
electrode welding (MMA) in direct current output(DC). These machines can weld all types of electrodes : rutile, basic/
low hydrogen (except 80P), stainless and cast iron. They’re protected to work with generators (230 V +- 15%).
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys GYSMI 160P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys GYSMI 160P in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info