625734

Gys GYSFLASH 4A Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
6/28
This manual contains important safety and operating instructions. Read this manual carefully before
using the charger for the first time and keep it in a safe place for future reference.
PRODUCT FEATURES
GYSFLASH is designed for charging a variety of SLA (Sealed Lead Acid) batteries, widely used in cars
and other vehicles. GYSFLASH 7A is suitable for WET/Flooded (Liquid Electrolyte), GEL (Gelatine type
Electrolyte, absorbed into the plates), AGM (Absorbed Glass Mat) and CA (Calcium) batteries.
GYSFLASH 7A charges 12V batteries (6 cells of 2V) from 1.2 Ah to 130 Ah, or provides a maintenance
charge for 12V batteries from 1.2 to 230 Ah.
GYSFLASH 4A charges 12V batteries (6 cells of 2V) from 1.2 Ah to 70 Ah, or provides a maintenance
charge for 12V batteries from 1.2 to 130 Ah.
SAFETY INFORMATION
Do not attempt to charge non rechargeable batteries.
If the power cable is damaged, stop using the machine. Any repair must be carried out by
GYS or an authorized repair agent in order to avoid danger.
Respect the fuse rating indicated on the charger.
Do not cover the charger while charging.
Always read the instructions carefully before charging. Unplug the charger from the mains
before connecting or disconnecting the clamps from the terminals of the battery.
Attention: Explosive gas, avoid sparks and flames. Ensure that the unit is in a sufficiently
ventilated area during charge.
Separate collection required. Do not dispose of in domestic refuse.
This device is not intended for use by persons (including children) with reduced physical or
mental capabilities, or lack of experience and knowledge, unless they have been given by a
person responsible for their safety, supervision or instructions concerning the use of the
device. Children should not play with the appliance. Cleaning and maintenance should not
be performed by unsupervised children.
During use the unit should be placed so that the mains socket is accessible.
CONNECTING
Charging of a permanently installed battery in a vehicle
a- Plug the charger into the mains
b- Check polarity of battery terminals. A positive (+) battery terminal usually has a larger diameter
than a negative one.
c- Identify the terminal of battery which is connected to the chassis (earth) - this is normally the
negative terminal.
d1- Charging a negative earthed battery:
Connect the red clamp to the positive (+) terminal of the battery and the black clamp to the
negative (-) terminal of the battery or to the vehicle chassis.
d2- Charging of positive earthed battery:
- Connect the black clamp to the negative (-) terminal of the battery and the red clamp to the
positive (+) terminal of the battery or to the vehicle chassis.
Charging a battery not connected to a vehicle
a- Plug the charger into the mains
b- Connect the red clamp to the positive (+) terminal of the battery and the black clamp to the
negative (-) terminal.
For permanent connection to the vehicle battery use the cable with eyelet terminals = accessory
n°15)
Warning: Do not connect the cables to the battery terminals during installation.
a- Connect the red cable to the positive (+) battery terminal
b- Connect the black cable to the negative (-) battery terminal
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys GYSFLASH 4A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys GYSFLASH 4A in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info