665732
20
Zoom out
Zoom in
Previous page
1/82
Next page
20
EXAGON 400 CC/CV
EN
SEMI-AUTOMATIC MIG / MAG WELDING WITH WIRE FEEDER (EXAFEED )
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type
(in general on the -)
,
• Connect the connection cable on the remaining power connector,
• Plug the connection cable’s command connector on the 10 points base situated between the two power connectors (FIG-1, n°5),
• Refer to the wire feeder’s user manual for the remaining connections.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
Both display show - - - and the knobs are inactive, all controls are now opera-
ted from the wire feeder’s interface (Refer to the wire feeders user manual for
the control settings).
Rutile
0
+9-9
Basic
ARC FORCE
INDUCTANCE
Cellulosic
6013
7018
6010
MMA
press 3 s
MIG TIG
setup
memory
Gouging
CV
MODE
MADE IN FRANCE
AV
VRD
press 3spress 3s
The grey areas are not useful for this mode.
SEMI-AUTOMATIC MIG / MAG WELDING WITH VOLTAGE DETECTING WIRE FEEDER ( )
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type
(in general on the -)
,
• Connect the wire feeder on the connector using a male-female cable (NOMAD CABLE),
• Refer to the wire feeder’s user manual for the remaining connections.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
1. Setting the welding voltage :
Adjust the welding voltage using the main knob depending on the work
to be carried out. The voltage setpoint is indicated on the left side display.
2. Inductance settings :
Adjust the inductance level using the second knob , a relative value from
-9 to +9. The lower the inductance level, the harder and more guiding the arc.
The higher the inductance and the softer the arc with little splatter.
Rutile
0
+9-9
Basic
ARC FORCE
INDUCTANCE
Cellulosic
6013
7018
6010
MMA
press 3 s
MIG TIG
setup
memory
Gouging
CV
MODE
MADE IN FRANCE
AV
VRD
press 3spress 3s
The grey areas are not useful for this mode.
CARBON ARC GOUGING
CONNECTIONS AND RECOMMENDATIONS
• Connect the earth clamp on the negative (-) terminal
• Connect the gouging torch on the positive (+) terminal
• Orient the clamp depending on the working position, make sure that the compressed air ows in the arc’s direction and not the other way around.
• Place a carbon electrode,
• Connect the compressed air to the gouging torch,
The arc strike is easier : just make contact with the piece, and advance while pushing the electrodes towards the metal to be removed.
MODE SELECTION AND SETTINGS
Press the button several times until the LED light switches on below the
symbol .
Adjust the arc voltage using the main knob , the voltage setpoint is is indi-
cated on the left side display.
• 36V to 45V for a 6.35 mm electrode.
• 39V to 45V for a 8 mm electrode.
Rutile
0
+9-9
Basic
ARC FORCE
INDUCTANCE
Cellulosic
6013
7018
6010
MMA
press 3 s
MIG TIG
setup
memory
Gouging
CV
MODE
MADE IN FRANCE
AV
VRD
press 3spress 3s
The grey areas are not useful for this mode.
DISPLAY CURRENT/VOLTAGE DURING WELDING
During welding, the machine measures and displays the welding current and voltage. After the weld, the average current and voltage values are
displayed during 30 seconds, as soon as a knob or a button is pressed, the welding parameters are displayed.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys EXAGON 400 CC-CV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys EXAGON 400 CC-CV in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info