665732
18
Zoom out
Zoom in
Previous page
1/82
Next page
18
EXAGON 400 CC/CV
EN
• The device turns into protection mode if the power supply tension below 340V RMS or over 460V RMS. To signal this fault, the screen displays an
error code.
• The start is done via an on / off switch (7) set to I, and the stop is done by switiching it to O. Attention ! Never disconnect the power supply
when the machine is on.
CONNECTION ON A GENERATOR
The machine can work with generators as long as the auxiliary power matches these requirements :
- The voltage must be AC, always superior to 400Vac ±15%, and the peak voltage below 700V,
- The frequency must be between 50 and 60 Hz.
It is imperative to check these requirements as several generators generate high voltage peaks that can damage these machines.
USE WITH EXTENSION CABLES
All extension cables must have an adequate size and section, relative to the machine’s voltage .
Use an extension that complies with national safety regulations.
Current input Extension selection (<45m)
400V 2.5 mm²
ELECTRODE WELDING (MMA AND MMA VERTICAL UP )
CONNECTIONS AND RECOMMENDATIONS
• Connect the cables, electrode holder and earth clamp in the connectors,
• Respect the welding polarities and intensities indicated on the electrodes boxes,
• Remove the electrode from the electrode holder when the machine is not in use.
Rutile
0
+9-9
Basic
ARC FORCE
INDUCTANCE
Cellulosic
6013
7018
6010
MMA
press 3 s
MIG TIG
setup
memory
Gouging
CV
MODE
MADE IN FRANCE
AV
VRD
press 3spress 3s
MMA
The grey areas are not useful for this mode.
Rutile
0
+9-9
Basic
ARC FORCE
INDUCTANCE
Cellulosic
6013
7018
6010
MMA
press 3 s
MIG TIG
setup
memory
Gouging
CV
MODE
MADE IN FRANCE
AV
VRD
press 3spress 3s
MMA Vertical up
The grey areas are not useful for this mode.
MODE SELECTION
Press the button several times until the LED light switches on below the symbol or .
The MMA vertical up mode adds a current pulse which makes vertical up welding easier.
MAIN SETTINGS
1. Selection of the electrode’s coating type :
Selection of the electrode’s coating type by maintaining the button for more than 3 seconds until the LED switches on below the corresponding
symbol.
2. Welding intensity settings :
Adjust the welding current using the main knob according to the electrode diameter and the type of assembly to be carried out. The current
setpoint is indicated on the right side display.
3. Arcforce settings :
Adjust the arcforce level with the right side knob , a relative value from -9 to +9. The lower the arcforce, the softer the arc.
The higher the arcforce, the higher the extra welding current . The default value is 0.
WELDING PARAMETERS
WELDING INTENSITY SETTINGS
The following settings concern the intensity range that may be used depending on the electrode’s type and diameter . These ranges are quite large
as they depend on the application and the welding position.
Ø electrode
(mm)
Rutile E6013
(A)
Basic E7018
(A)
Cellulosic E6010
(A)
1.6 30-60 30-55 -
2.0 50-70 50-80 -
2.5 60-100 80-110 60-75
3.15 80-150 90-140 85-90
4.0 100-200 125-210 120-160
5 150-290 200-260 110-170
6.3 200-385 220-340 -
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys EXAGON 400 CC-CV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys EXAGON 400 CC-CV in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info