The 4T mode allows the user to manage various steps with the trigger The behaviour varies depending on the activation / deactivation of the Hots-
tart and Crater Filler features.
Burnback
Start
Hotstart
(1)
WeldingCrater Filler
(2)
Voltage
Wire speed
Gas
Released
Held
Trigger
(1)
:
if the Hotstart feature is active, the Hotstart phase lasts until the trigger is released. If the Hotstart feature is deactivated, the pregas phase
lasts while the trigger is held (no graph).
(2)
:
if the Crater Filler feature is active, the Crater Filler phase lasts while the trigger is held. If the Crater Filler is deactivated, the postgas phase
lasts while the trigger is held (no graph).
Spot / Delay mode:
The Spot / Delay is a 2T mode to weld beads of a specic length (Spot settings expressed in seconds) with a specic spacing (Delay settings
expressed in seconds). If the Delay setting is set to 0.0 seconds then a single weld bead will be welded, you will have to release and press the
trigger again to weld another weld bead.
REMOTE CONTROL
A remote control (ref. 045675) can be connected to the EXAFEED wire feeder via the connector (FIG-1, 5). The remote control acts on the voltage
(1st potentiometer) and the wire speed (2nd potentiometer). Thus these settings cannot be accessed on the wire feeder’s interface.
LOCKING CONTROLS
That feature can lock the knobs and keypad to prevent accidental changes in the settings.
Operation :
Press the button for 3 seconds, the display shows and goes back to current display. The LED
(FIG-2, n°13)
switches on.
No button is enabled, the knobs can adjust the voltage and wire speed (value at +/- of the percentage, dened by the «tol» setting)
(see the welding machine’s instruction manual).
To unlock the commands, press the button for 3 seconds, the display shows then goes back to current display. The LED (FIG-2,
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Gys EXAFEED 4L at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Gys EXAFEED 4L in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.
The manual is 5,98 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
