625804

Gys BT280 Manual

3
Zoom out
Zoom in
Previous page
1/32
Next page
- GB.3-V1 -
BATTERY TEST- 12V
1. Before you test a battery in a vehicle, turn off the ignition, all
accessories and loads. Close all the vehicle doors and the trunk lid.
NOTE:
If vehicle has been running before testing, the battery
holds a surface charge. Turn on headlights for 30 seconds to
remove surface charge. Let battery rest for one minute
before starting to test.
2. Make sure the battery terminals are clean. Wires brush them if
necessary. Clamp the black load lead to the vehicle negative battery
terminal. Clamp the red load lead to the vehicle positive battery
terminal.
3. LCD lights on and shows the voltage of the battery XX.XXv on the
screen. Please press ϧ\ϰ key to select BAT. for battery tester.
Press "ENTER" to the next step.
NOTE :
If you see HI / LO / blank / RIPPLE appeared on the
screen or flickers, please refer to TROUBLESHOOITING.
4. Please press ϧ\ϰ key to select the battery type of
SLI / AGM / VRLA/GEL:
SLI : Standard SLI flooded batteries.
AGM : AGM sealed batteries.
VRLA/GEL : VRLA/GEL sealed batteries.
5. Press "ENTER" to the next step.
6. Please press ϧ\ϰ key to select the battery rating of
SAE/CCA , DIN , EN , CA/MCA or IEC.
- GB.2-V1 -
come to your aid when you work near a lead acid battery.
2. Have plenty of fresh water and soap nearby in case battery acid
contacts skin, clothing or eyes.
3. Wear safety glasses and protective clothing.
4. If battery acid contacts skin or clothing, wash immediately with
soap and water. If acid enters eye, immediately flood eye with
running cold water for at least ten minutes and get medical
attention immediately.
5. NEVER smoke or allow a spark or flame in vicinity of battery or
engine.
6. Be extra cautious to reduce risk of dropping a metal tool onto the
battery. It could spark or short-circuit the battery or other electrical
parts and could cause an explosion.
7. Remove personal metal items such as rings, bracelets, necklaces
and watches when working with a lead acid battery. It can produce
a short circuit current high enough to weld a ring or the like to
metal causing a severe burn.
PREPARING TO TEST :
1. Be sure area around battery is well ventilated while battery is being
tested.
2. Clean battery terminals. Be careful to keep corrosion from coming
in contact with eyes.
3. Inspect the battery for cracked or broken case or cover. If the
battery is damaged, do not use tester.
4. If the battery is not sealed maintenance free, add distilled water in
each cell until battery acid reaches level specified by the
manufacturer. This helps purge excessive gas from cells. Do not
overfill.
5. If necessary to remove battery from vehicle to test, always remove
ground terminal from battery first. Make sure all accessories in the
vehicle are off to ensure you do not cause any arcing.
OPERATION & USE :
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys BT280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys BT280 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info