Manual Gymrex GR-HG12 (page 7 of 23) (English, German, French, Italian, Polish, Spanish)

779081

Zoom out

Zoom in

1/23

• Standby mode – the device enters into standby

mode after 10 minutes of inactivity, press any button

to turn device on.

• To stop the device, press the „STOP“ button. Pressing

and holding the „STOP“ button for 2 seconds will

restart the device.

3.4. CLEANING AND MAINTENANCE

a) Unplug the mains plug and allow the device to cool

completely before each cleaning, adjustment or

replacement of accessories, or if the device is not

being used.

b) Store the unit in a dry, cool place, free from moisture

and direct exposure to sunlight.

c) Do not spray the device with a water jet or submerge

it in water.

d) The device must be regularly inspected to check its

technical eciency and spot any damage.

e) Use a soft cloth for cleaning.

f) For proper operation of the device, every 30 hours of

work, apply silicone oil under the treadmill belt, then

turn the device on for 3 minutes without load.

2. Remove the screws and washers from the panel. One

person has to hold the panel and the other person

connects the wire which is located on the panel and

right side of the frame (make sure that the wire is

properly connected, do not connect at a push). Then

x the panel to the frame with screws and washers.

Tighten all bolts, including those that have not been

attached previously. Then put the security key in the

yellow area of the panel.

3. Attach the frame to the treadmill with the M12 knob.

4. You can adjust the tilt before use.

3.3. DEVICE USE

Caution: Before starting training, place the safety key on

the panel and place the clip on your clothing. Pulling rmly

on the safety key cord will stop the treadmill belt.

GR-HG12 MODEL

• Press the button and the device will start after 3

seconds (at a speed of 1 km/h).

• It is possible to change: distance, time and calories

with the „MODE” button.

• The values can be adjusted using the „-“ and „+“

buttons.

• The device has 12 programs, press the „PROGRAM“

button, select the appropriate program and conrm

with the button (speed and time cannot

be changed; the default program duration is 30

minutes).

• To stop the device, press the button .

MODEL GR-MG30

• Press the „START“ button, the countdown on the

screen will begin and the device will start at a speed

of 1 km/h.

• You can adjust the speed with the „-“ and „+“

buttons. Speed control is also possible with the quick

dial buttons „3“, „6“, „9“, „12“.

• It is possible to change: distance, time, calories,

program with the „MODE“ button.

• Heart rate program – press the „PROGRAM“ button

to select the HR mode (HR 1 / HR2), use the „MODE“

button or the „+“ / „-“ buttons to set the age, then

press the „MODE“ button, the device will calculate

the heart rate data . Press the „+“ or „-“ button to

change the settings.

• BMI program – press the „BMI“ button and enter

the FAT mode, press the „MODE“ button to set the

parameters (F-1 sex, F-2 age, F-3 height, F-4 weight),

changing parameters is possible using the „+“ and

„-“ buttons. After setting all parameters, press the

„MODE“ button, the display will show „---“, then

touch the heart rate sensor, the device will calculate

the body mass index.

Parameters selection

Parameter Default

settings Range Description

Sex F-1 2 1/2 1 - Male

2 - female

Age F-2 35 10~99

Height F-3 170 50~250 Unit: CM

Weight F-4 60 20~200 Unit: KG

Body mass index

Body mass index (BMI) Weight disorders

<19 Underweight

19~26 Proper

26~30 Overweight

>30 Obesity

ADJUSTING THE TREADMILL BELT

1. After unpacking the device, place it on a at surface.

Raise the device’s frame vertically. Lock the frame

with the two knobs.

2. Position the handrail horizontally and secure it with

the bolt.

3. Position the handle as shown in the gure. If the

handle is to be placed lower, remove the screw.

4. Place the safety key on the yellow background of the

control panel.

MODEL GR-MG30

1. Attach the left and right sides of the frame to the

base with provided screws and washers, do not

tighten the screws. Then fasten the handrail with the

bolts without tightening the bolts.

2 3 4 5

6 7 8 9

422

1 2

3 4

1. If the treadmill belt tilts to the left – Start the device,

set the speed at 2–3 km/h without load on the belt,

use the Allen key to rotate the screw by 1/4 of a turn.

Then let the machine run for 1–2 minutes without

load. Repeat the process until the belt returns to the

correct position (picture ).

2. If the treadmill belt tilts to the right – Start the device,

set the speed at 2–3 km/h without load on the belt,

use the Allen key to rotate the screw by 1/4 of a turn.

Then let the machine run for 1–2 minutes without

load. Repeat the process until the belt returns to the

correct position (picture 2).

3. If a jam of the treadmill belt occurs - use the Allen

key to turn the bolts on both sides by 1/2 of a turn

counterclockwise until the lock is removed (gure 3).

STORAGE

MODEL GR-HG12

1. Disconnect the device from the power supply.

Remove the bolt to fold the handrail of the device.

2. Pull out the knobs on both sides of the frame.

Reassemble the device, then use the knob to secure

the treadmill.

3. Remove the handle and place the device in a secure

position.

MODEL GR-MG30

Disconnect the device from the power supply. Unscrew the

M12 knob and then raise the platform with the treadmill.

Then secure with the M12 knob.

DISPOSING OF USED DEVICES

Do not dispose of this device in municipal waste systems.

Hand it over to an electric and electrical device recycling

and collection point. Check the symbol on the product,

instruction manual and packaging. The plastics used

to construct the device can be recycled in accordance

with their markings. By choosing to recycle you are

making a signicant contribution to the protection of our

environment. Contact local authorities for information on

your local recycling facility.

14.12.2020

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gymrex GR-HG12 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 4.64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gymrex GR-HG12 Manual

Product: