776223

Guide EasIR-4 Manual

4
Zoom out
Zoom in
Previous page
1/28
Next page
User Manual
1
Introduction
This publication provides the necessary information required to safely operate the EASIRTM-4 Thermal Camera.
It is important to fully check all equipment with which you have been supplied.
The equipment should be used, maintained and serviced by suitably trained personnel, capable of carefully following
the procedures and guidelines given in this User Manual.
All User Manuals and leaflets should be read thoroughly before proceeding with operation of the equipment.
It is also advisable that all User Manuals and Instruction Leaflets supplied are kept readily available, for reference when
the equipment is in general use.
Precautions
The following precautions must be adhered to at all times and must be considered in addition to any advised
precautions issued at the relevant worksite or work area.
• Keep the EASIRTM-4 Thermal Camera steady during operation.
• Do not use the EASIRTM-4 Thermal Camera in temperature exceeding its working and storage temperature
ranges.
• Do not direct the EASIRTM-4 Thermal Camera at very high intensity radiation sources such as the sun,
carbon dioxide lasers or arc welders etc.
• Do not expose the EASIRTM-4 Thermal Camera to dust and moisture. When operating the unit near water,
ensure that the unit is adequately guarded against splashes.
• When the EASIRTM-4 Thermal Camera is not in use or is to be transported, ensure that the unit and its
accessories are stored in the protective carry case.
• Do not jam the holes or loudspeaker on the camera body.
• Do not re-switch on the camera until 15 seconds later after switching it off.
• Do not throw, knock or vibrate intensely the camera and its components in order to keep them from damage.
• Do not attempt to open the camera body, as this action will void the warranty.
• Keep the SD memory card for the exclusive use of the camera.
• During using, if move the IR camera from hot/cold place to cold/hot place, e.g. from inside/outside to
outside/inside of a air-conditioned car in winter, should power off the camera firstly and leave it in the
operation site for 20 minutes, then power on the camera for normal operation and accurate temperature
measurement. Sharp and instant ambient temperature change may cause fault temperature measurement
and even damage camera’s IR detector.
• FPA setting: to ensure accurate temperature measurement, the FPA detector was calibrated in different
temperature points--7degree, 17degree, 27degree, 37degree. When power on the camera in 0 degree for
example, after period of working the temperature of the camera (the detector) will increase gradually. And
when the internal temperature of the camera beyond 7 degree, FPA setting will take place and will last for
about 30sec, and during the FPA setting the camera will not response for any operations. If power on the
camera in a temperature about 8 degree, only when the temperature of the camera beyond 17degree, this
phenomenon will happen again. Camera will adjust FPA setting itself automatically to ensure its stable
performance.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Guide EasIR-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Guide EasIR-4 in the language / languages: English as an attachment in your email.

The manual is 1.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Guide EasIR-4

Guide EasIR-4 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info