Manual Gude WS 125-1150 E 58108 (page 20 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Turkish)

624890

Zoom out

Zoom in

1/100

ENGLISH

DEGB

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments of

workpiece or of a broken accessory may y away and

cause injury beyond immediate area of operation.

j) Hold the power tool by insulated gripping sur-

faces only, when performing anoperation where

he cutting accessory may contact hidden wiring

or its own cord. Cutting accessory contacting a „live“

wire may make exposed metal parts of the power tool

„live“ and could give the operator an electric shock.

k) Position the cord clear of the spinning accesso-

ry. I

f you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

wheel.

l) Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

ccessory may grab the surface and pull the power

tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning acces-

sory could snag your clothing, pulling the accessory

nto your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

o) Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel. Pinching or snaggingcau

ses rapid stalling of the rotating wheel which in turn

auses the uncontrolled power tool tobe forced in

the direction opposite of the wheel’s rotation at the

point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of

the wheel’s movement at the point of pinching. Ab-

rasive wheels may also break under these conditions.

ickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a rm grip on the power tool and

position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback or

torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper

precautions are taken.

b) Never place your hand near the rotating ac

cessory. Accessory may kickback over your hand.

) Do not position your body in the area where

power tool will move if kickback occurs. Kickback

will propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have

a tendency to snag the rotating accessory and cause

loss of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create frequent

kickback and loss of control.toothed saw blade.

Safety Warnings Specic for Grinding and Abrasi

ve Cutting-O Operations:

Use only wheel types that are recommended

for your power tool and the specic guard desi-

gned for the selected wheel. Wheels for which the

ower tool was not designed cannot be adequately

guarded and are unsafe.

b) The grinding surface of the centre depressed

wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel that

projects through the plane of the guard lip cannot

be adequately protected.

c) The guard must be securely attached to the

power tool and positioned for maximum safety,

so the least amount of wheel is exposed towards

the operator. The guard helps to protect the opera

tor from broken wheel fragments, accidental contact

ith wheel and sparks that could ignite clothing.

d) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-o wheel. Abrasive cut-o wheels are

intended for peripheral grinding, side forces applied

to these wheels may cause them to shatter.

e) Always use undamaged wheel anges that

are of correct size and shape for your selected

wheel. Proper wheel anges support the wheel thus

reducing the possibility of wheel breakage. Flanges

for cut-o wheels may be dierent from grinding

wheel anges.

f) Do not use worn down wheels from larger

power tools.Wheel intended for larger power tool

is not suitable for the higher speed of a smaller tool

and may burst.

Additional Safety Warnings Specic for Abrasive

Cutting-O Operations:

a) Do not “jam” the cut-o wheel or apply excessi

ve pressure. Do not attempt to make an excessive

epth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or binding of

the wheel in the cut and the possibility of kickback or

wheel breakage.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude WS 125-1150 E 58108 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Turkish as an attachment in your email.

The manual is 2,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude WS 125-1150 E 58108 Manual

Product: