622092

Gude PROFI- S - 40140 Manual

9
Zoom out
Zoom in
Previous page
1/58
Next page
Storage
Always disconnect all pneumatic appliances if not used.
Always store the appliance at a dry place.
Assembly and first putting into operation (pic. III)
After unpacking, the appliance needs to be carefully
inspected for possible damage at transport. It is also
necessary to unconditionally ensure that all screws,
connections, etc. were tightened.
Mix and dilute the colour according to producer's
instructions. Most of the colours can be processed better
when correspondingly diluted.
Before processing, it is recommended to re-filter the
colour.
Fill the container to ¾.
Do not exceed in any case the maximum pressure
of the gun or other system components for compression!
Ensure that the vacuum container was correctly closed
and the air hose firmly connected to the gun.
Prepare a piece of cardboard that you can use during
adjustment.
Never aim the gun at other persons or yourself,
failing which there can be serious injuries.
Connect the gun now (see pic. III) to the compressed air
source.
Upon compressor switching on, check the substance
density, aim the gun at the cardboard and trigger the
starter several times. If the material is too dense, add
some solvent and proceed very carefully and do not
deviate from the substance density recommended by the
producer.
Setting (pic. I) + (pic. II)
The spraying shape, outlet volume and general appearance
of the colour layer can be set as follows.
A round or elliptical spraying shape can be reached by
turning on the air volume controller (2).
The outlet colour volume reduces on the colour volume
controller (3) by turning rightwards. Turning leftwards
increases the squirted liquid volume.
The air volume reduces on the air pressure controller (6) by
turning rightwards and increases by turning leftwards.
(pic. II)
• K spray is wrong.
The layer thickness does not differ much at
swinging.
• L spray is correct.
Always apply evenly “wet spraying to wet“
• Optimum spray can be reached at a distance
of app. 15-20 cm. A too small distance and too
fast or too slow motions result in wrong spray.
Tip: Take a piece of cardboard and make test spraying
before each work.
Maintenance and treatment
Disconnect the appliance from compressed air
source at maintenance and treatment.
Clean and treat the gun immediately
after varnishing with a
maximum care. A cleaned gun guarantees trouble-free
handling at another use. If the nozzle is removed at cleaning,
the thread and seal must be treated with light fat. That will
prevent nozzle “biting in“.
Attention: Do not put
the entire gun to a bath with solvent.
The nozzle and nozzle needle are quickly-worn parts,
therefore you should always have a set of spare nozzles with
you.
Store the pneumatic tools/appliances in dry rooms only.
Only a regularly maintained and treated appliance can serve
as a satisfactory aid. Insufficient maintenance and care can
lead to unforeseen accidents and injuries.
Failure removal
Failure Cause Removal
Gun does not
spray
1. Blocked/stic
ky
nozzle/nozzl
e needle.
2. Faulty
nozzle/nozzl
e needle.
3. Blocked/
sticky colour
container.
1. Clean the
nozzle/nozzle needle.
2. Replace the
nozzle/nozzle needle.
3. Clean or replace the
container.
Appliance
not supplied
with
compressed
air
1. Jammed,
broken or
faulty
pneumatic
hose.
1. Check the pneumatic
hose and replace it
when faulty.
Piston does
not return to
full, stroke
with no load
1. Appliance
applied too
weakly or
too shortly.
2. Piston drags
as it is not
lubricated.
3. O-ring faulty
1. Apply the appliance
more strongly.
2. Lubricate the cylinder
guide surface.
3. Replace the O-ring.
9
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude PROFI- S - 40140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude PROFI- S - 40140 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info