Manual Gude Pro 1.5 PRO 75130 (page 22 of 29) (English, German, Dutch, French, Italian)

629039

Zoom out

Zoom in

1/29

Store the cleaning cloths and other combustible

material in sealed metal containers. These containers

must be disposed according to local, national and

regional provisions.

When the appliance is operated the air pressure MUST

NOT exceed 6.3 bar. Use a pressure regulator that will

reduce the air pressure to 6.3 bar.

ALWAYS use the appliance in a safe distance from

people and animals.

Make sure the speed of rotating of accessories parts

corresponded to the speed of rotating of the impact

tightener or was higher.

Before starting

Air supply

Important information on the appliance can be found in

model specifications.

Lubricate the appliance before putting it into

operation (see the Maintenance part).

Assembly

Always disconnect the air supply hose when you want

to assembly socket nuts or extensions on the

appliance or disassemble them from the appliance.

Operation

Safety notice!

Wear protective glasses! Wear ear

protectors!

Always empty water from the compressor tank and

blow condensation out of the air hose before everyday

operation.

Now start your compressor. The maximum service

pressure of air is 6.3 bar.

The power (torque) of impact tighteners under primary

working conditions is especially determined by three

factors:

a) service pressure used

b) time of working step on the threaded joint. A normal

work time for a threaded joint is 3-5 seconds on

average.

c) setting of the switching lever, in relation to the

threaded joint in proportion to the impact time.

Due to the use of threads and materials of various

hardness there is an increased friction, which causes

higher torque without the thread being tightened more

firmly. At rust-stained threaded joints, use appropriate

agents dissolving rust before using the impact

tightener. If the threaded joints still fail to unloose after

3 to 5 seconds of impact time it is necessary to use a

one lever bigger impact tightener. Do not overload the

impact tightener above the specified power limit as it

dramatically shortens the service life of the appliance.

NOTE: The tightening torque on the threaded joint is

directly connected with the thread firmness, appliance

revolutions, condition of the power socket nuts used

and time of use of the impact tightener at the given

screwing. Use as direct and simple connection

between the appliance and power socket nut as

possible. Any extra connection and extension absorb

and reduce the power.

Picture 2 shows setting of enabling torques

Pic. 2 A: Full enabling torque 1,500 Nm

Pic. 2 B: Tightening torque, partial load 300 Nm

Pic. 2 C: Tightening torque, half load 800 Nm

Pic. 2 D: Tightening torque, full load 1,000 Nm

Maintenance and treatment

Lubrication

1. Disconnect the impact tightener from air

supply.

2. Add 4-6 drops of GUDE pneumatic oil, Order

No. 40060 (we recommend the GÜDE mist

lubricator, Order No. 41354) or corresponding

oil to air inlet with the starter being pressed.

3. Now reconnect the appliance with air supply

and leave it run for app. 30 seconds so that

the surplus oil flowed out.

This lubricating process corresponds to the reduction

of humidity, dust and impurities that are in course of

time deposited, when the appliance is used, in each

compressor and thus reduce its power. This is best

prevented by integrated oil tanks.

Safety notice! Leaked oil can cause

serious injuries. Cover the top of oil outlet

after cloth greasing and leave the

appliance run for several seconds so that

surplus oil could safely flow out. Keep the

cloth in a safe distance from the rotary

parts!

The air hose must be disassembled and larger volume

of pneumatic oil poured to the air inlet each three

months or if the impact tightener is used only

sometimes. Reconnect the air hose and leave the

impact tightener run for app. 30 seconds so that the

compressor engine was cleaned. Follow the lubrication

instructions after cleaning.

Failure removal

Problem Possible cause Solving the problem

Insufficient air pressure Check the air pressure on the air

inlet. It must be 6.3 bar.

Air pressure set low Increase the pressure to 6.3 bar

Impact tightener must be oil-

lubricated

See the Lubrication

Impact tightener must be cleaned See the Maintenance

Impact tightener is not working or is

running slowly

Air hose not tight Tighten all hose screwed joints

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude Pro 1.5 PRO 75130 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude Pro 1.5 PRO 75130 Manual

Product: