Manual Gude MP 120-5A-GJ 9418 8 (page 15 of 80) (English, German, Dutch, French, Italian)

628420

Zoom out

Zoom in

1/80

5.2 Safety Instructions for the First Putting in Operation

Caution: Never let the pump dry-run

 The user shall be held liable before third parties for operating the pump (basins, reservoirs etc.).

 The pump should be used on connections with a stray current protection switch (FI switch)!

 Before putting in use, a competent electrician should check that extension cables are available.

 Connection to the mains via plugging.

 The user shall be held liable before third parties for operating the pump (basins, reservoirs etc.).

 The pump should be used on connections with a stray current protection switch (FI switch)!

 Before putting in use, a competent electrician should check that extension cables are available.

 Connection to the mains via plugging.

 No people or animals should be/ be diving in the water to be pumped (pools, cellars etc.).

 Temperature of the fluid to be pumped should not exceed +35° C. If extension cables are use they should be only of

rubber type H07RNF + H05RNF, according to standards DIN 57282 or DIN 57245. Never pull or hold the pump connected

to the mains by the cable. Be particular about keeping the plug away from water and moisture so that the plug is protected

against moisture.

 Before putting the pump in operation check the electric cable and/or the plug for damage. .

 Unplug the pump before doing any work on it.

 If the pump is built in a gully hole, the hole should be covered up after completion of the job in order to ensure the safety

of pedestrians.

 The owner (user) should take appropriate safety measures (alarm installation, stand-by pump etc.) in order to prevent

damages (flooded space etc.) resulting from aggravated operations of the pump (faults or defects).

 If the pump is found defective, the repair shall be done by an authorised servicing facility only. Only genuine spare parts

should be used.

 Please note that according to effective standards, we shall not be held liable for any damage caused by our units if

anything indicated below applies:

 Inappropriate repairs done by other than authorised servicing facilities

 Non-observation of determination or use other than in compliance with the determination ;

 Pump overloading in result of continuous operation ;

 Damages caused by frost and other weather effects ;

Never expose the pump motor to weather effects or have it immersed in water (if outdoors, cover up the

unit or keep it at a protected place)

Same regulations apply to the accessories.

5.2.1 Connecting Cable

The pump has not got any fee cable. This may be connected by a professional electrician only.

5.2.2 Overheating Thermal Fuse

Inside the motor, there is a probe fitted that will switch the pump off on exceeding certain temperature automatically and will

switch it on again after the unit cooled down. That will multiply the service life of the unit and the motor burning is prevented.

5.2.3 Overheating Fuse/ Thermal Protection Motor Circuit Breaker

A motor thermal breaker is fitted on the pump. If the motor gets overheated, the breaker will switch the pump off automatically.

Cooling time is 25 minutes, afterwards, the pump will go on automatically. If the breaker switches, it is essential to find and

remove the cause (see also Faults seeking) The data indicated in this context should not be regarded instructions for home-

made repairs as the repairs require specific expert knowledge. Always consult a customer servicing centre at any faults.

6 Operation

6.1 De-aeration

Fig. 14

 Remove the bleed screw so that any trapped air may escape.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude MP 120-5A-GJ 9418 8 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude MP 120-5A-GJ 9418 8 Manual

Product: