628565

Gude HWW CAB 200-100-400 V 94193 Manual

12
Zoom out
Zoom in
Previous page
1/67
Next page
We have to draw your attention to the fact that
according to the valid standards we cannot take
responsibility for below mentioned cases of possible
damage caused by our devices:
Unproper repairs performed by unauthorized service repair
shops;
Using pump for a different purpose or failing to observe its
use according to the provisions;
Overloading of the pump by long-term operation;
Protection against Thermal Overloading
A sensor is built into the engine that automatically switches off
the pump if a certain temperature has been exceeded, and/or
it switches the pump on after it has been cooled. This
increases the service life of the pump quadruptly, and
prevents burning of the electric engine.
Protection against Overloading /Thermoswitch of the
Engine
The pump is furnished with an engine thermoswitch. If the
motor is overheated, the thermoswitch switches the pump
automatically off. The cooling period makes approx. 25
minutes, thenafter the pump will be automatically switched
on again. If the engine switch is on, it is necessary to find
and remove the cause (see also “Troubleshooting”). The
data here given cannot be considered as instructions for
“home made” repairs, because the repair works require
specific professional knowledge and skill.
Therefore you have to contact customer service if any
failure occurs.
It is unconditionally necessary to secure good air
supply in order to prevent overheating of the pump!
Do not install the pump in too tight shifts, do not cover
it with anything!
Operation
Air pressure
Pull out the network plug.
Open the consumption valve, e.g. water main tap, so that the
water may be pressed out of the system..
Turn the protection lid on the bleeding valve in the down
direction (F).
Check the air pressure in the vessel with compressor and
device for tyre pumping.
The specified air pressure is 1,5 ± 0,3 bar.
Bleeding
Release the bleeding screw and let the possible closed air
escape. (Fig. A; pos. 2)
Water Bubbles
Release the screw for draining water bubbles so that the
pump may be drained (Fig. A; pos.11)
Vessel pressure
Switch off pressure set by the manufacturer is 3-4 bar after
completion of filling.
Setting pressure of the vessel (air) makes 1,5 ± 0,3 bar
and it should be regularly checked and modified (G).
Safety Instruction for Operator
Use the device only after you have carefully read Operating
Manual.
Observe all safety instructions mentioned in the Manual.
Behave responsibly against other persons
Instruction Step-by-Step
• Connect the suction pipeline that complies with the
outlet connecting pipe to the check valve (D) (foot
valve). Tighten all threading connections by sealing
band (B)
• After filling up remove the bleeding screw on the
back side of the pump and on the connecting line of
pressure pipeline. (Fig. A; pos. 1 and 2) Fill the
device up until the water exits from the bleeding
hole (Fig. A; pos. 2). (E)
• Make tight the bleeding screw and retight it again.
Then make tight the pressure pipeline and connect
it.
• Connect the pump to the electric network.
Caution: When installing suction and pressure
pipeline on corresponding connection lines, the
corresponding thread shall always be tightened
carefully so that no damage occurs due to cracking of
the pump shell (A) !
Caution: Careful sealing of thread connections
(A/B) and airless filling (E) of suction system – (suction
hose and pump shell) , will save you from trying to
perform suction that may often be unsuccessful!
Check the tightness of the foot valve (D) – Fill the
system according to the instruction (C) and pull the
suction hose out of the medium being repumped before
putting into operation for the purpose of checking (D) -
the liquid should not escape from the suction hose
now!
Important: Should the pump be out of operation for a longer period of time, the pipeline and the pump shell must be
unconditionally emptied.
Troubleshooting
CAUTION: FIRST OF ALL CHECK ALWAYS THE FUSES AGAINST OVERLOADING!
Failure Cause How to remove the failure
Engine cannot be
started.
No nework voltage.
Pump wheeel is blocked.
Check the voltage.
Turn the engine shaft with screwdriver through the fan
cover (to release friction circles sealing that may be
stuck together)
The pump does not
suck
Missing, untight or blocked foot valve
Foot valve is not in water.
No water in the pump shell.
Too high suction height.
Air bubbles in suction pipeline.
Connections not sealed, the pump sucks the air,
the pump is not bleeded.
Assembly or clean the foot valve.
Immerse the foot valve into water.
Fill the pump shell with water.
Check the suction height.
Check the tighting of suction pipeline.
Carefully repeat connection according to chapter
„Putting into Operation“!
Insufficient quantity of
water to be repumped.
Too high suction height.
Foot valve suction basked dirty
Check the suction height.
Clean tne suction basket.
12
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude HWW CAB 200-100-400 V 94193 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude HWW CAB 200-100-400 V 94193 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info