Manual Gude HWW 1200 2 (page 32 of 43) (English, German, Dutch, French, Italian)

628568

Zoom out

Zoom in

1/43

responsibility for below mentioned cases of possible

damage caused by our devices:

Unproper repairs performed by unauthorized service repair

shops;

Using pump for a different purpose or failing to observe its

use according to the provisions;

Overloading of the pump by long-term operation;

Protection against Thermal Overloading

A sensor is built into the engine that automatically switches off

the pump if a certain temperature has been exceeded, and/or

it switches the pump on after it has been cooled. This

increases the service life of the pump quadruptly, and

prevents burning of the electric engine.

Protection against Overloading /Thermoswitch of the

Engine

The pump is furnished with an engine thermoswitch. If the

motor is overheated, the thermoswitch switches the pump

automatically off. The cooling period makes approx. 25

minutes, thenafter the pump will be automatically switched

on again. If the engine switch is on, it is necessary to find

and remove the cause (see also “Troubleshooting”). The

data here given cannot be considered as instructions for

“home made” repairs, because the repair works require

specific professional knowledge and skill.

Therefore you have to contact customer service if any

failure occurs.

It is unconditionally necessary to secure good air

supply in order to prevent overheating of the pump!

Do not install the pump in too tight shifts, do not cover

it with anything!

Operation

Air pressure

Pull out the network plug.

Open the consumption valve, e.g. water main tap, so that the

water may be pressed out of the system..

Turn the protection lid on the bleeding valve in the down

direction (F).

Check the air pressure in the vessel with compressor and

device for tyre pumping.

The specified air pressure is 1,5 ± 0,3 bar.

Bleeding

Release the bleeding screw and let the possible closed air

escape. (Fig. A; pos. 2)

Water Bubbles

Release the screw for draining water bubbles so that the

pump may be drained (Fig. A; pos.11)

Vessel pressure

Switch off pressure set by the manufacturer is 3-4 bar after

completion of filling.

Setting pressure of the vessel (air) makes 1,5 ± 0,3 bar

and it should be regularly checked and modified (G).

Safety Instruction for Operator

Use the device only after you have carefully read Operating

Manual.

Observe all safety instructions mentioned in the Manual.

Behave responsibly against other persons

Instruction Step-by-Step

• Connect the suction pipeline that complies with the

outlet connecting pipe to the check valve (D) (foot

valve). Tighten all threading connections by sealing

band (B)

• After filling up remove the bleeding screw on the

back side of the pump and on the connecting line of

pressure pipeline. (Fig. A; pos. 1 and 2) Fill the

device up until the water exits from the bleeding

hole (E)

• Make tight the bleeding screw and retight it again.

Then make tight the pressure pipeline and connect

it.

• Connect the pump to the electric network.

Caution: When installing suction and pressure

pipeline on corresponding connection lines, the

corresponding thread shall always be tightened

carefully so that no damage occurs due to cracking of

the pump shell (A) !

Caution: Careful sealing of thread connections

(A/B) and airless filling (E) of suction system – (suction

hose and pump shell) , will save you from trying to

perform suction that may often be unsuccessful!

Check the tightness of the foot valve (D) – Fill the

system according to the instruction (C) and pull the

suction hose out of the medium being repumped before

putting into operation for the purpose of checking (D) -

the liquid should not escape from the suction hose

now!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude HWW 1200 2 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude HWW 1200 2 Manual

Product: