628589

Gude HPC 200 86001 Manual

10
Zoom out
Zoom in
Previous page
1/49
Next page
General guidelines
Ensure proper water supply before turning on the high-pressure
cleaner. Pump dry run causes major damage to the gasket system.
Do not unplug the power plug by pulling on the power cord.
In winter, the high pressure cleaner must be stored in a frost-free location.
The cross-section of the extension cords used must correspond to the cord length, e.g. a longer extension cord
must have a larger cross-section, and vice versa. In addition, protection class “IPX5” extension cords must be
used. See the following table for additional details.
Clean water intake filter regularly!
Voltage
Volt
Extension up to 25 m Extension up to 50 m
MOTOR
220 -230
240
Cross-section 3x1.5mm² Cross-section 3x2.5mm²
Set-up the high-pressure cleaner near the water source.
The packaging elements can be recycled, and consequently they must be disposed of according to the state-specific
guidelines.
The high-pressure cleaner may only be operated with the accessories and replacement parts recommended by the manu-
facturer. The use of original parts (accessories and replacement parts) assures safe and problem-free operation of the
high-pressure cleaner.
The high-pressure cleaner must be placed on a safe and stable substrate.
The high-pressure cleaner is designed exclusively for cleaning vehicles, machines, boats, buildings, etc., and for removing
stubborn grime with clean water and biodegradable cleaning agents.
The high-pressure cleaner is intended for private use only; it is not intended for professional use (industry, commercial).
Cleaning vehicles is only permitted in facilities with oil separation.
Installation
Connect the HP gun to the high-pressure hose.
Connect the high-pressure hose to the water discharge of the high-pressure cleaner.
Connect the water supply hose to the water input of the high-pressure cleaner. The hose diameter must be at least 13 mm;
the hose itself must be reinforced.
The temperature of the out-flowing water may not exceed 50 UNDER ANY CIRCUMSTANCES. The water pressure
may NOT exceed 10 bar.
ATTENTION: The high pressure cleaner should be operated with clean water.
Switch the motor switch to “ON”.
The power outlet intended for connecting the high-pressure cleaner must correspond to the voltage and frequency (V/Hz)
specified on the nameplate.
Observe the rules of your water supply company.
Eventuel you need to install a backflow preventer to prevent the backflow into the drinking water network (cleaning
agents).
Use
Open the water line cock COMPLETELY.
Unlock gun, open it and leave it in this condition for several seconds to vent as well as to blow off residual pressure
from the lines.
Start the motor with the switch when the gun is open.
The gun must be opened when switching the motor on again.
If the pistol is open, then the drop in pressure automatically starts the motor. The pressure is restored with a minimum delay.
USING CLEANING AGENTS: Connect the foam injector container with cleaning agent on the spray tube. Then apply the suc-
tioned-in cleaning agent mixed with water.
After concluding the work:
Switch-off the high-pressure cleaner.
Close water cock.
Discharge residual pressure from the gun, until all the water has escaped from the adjustable nozzle head.
Unplug the plug from the power outlet.
Maintenance
Attention: Always unplug the high pressure cleaner from the power source before performing any work on the unit.
For problem-free function of the high-pressure cleaner, check and clean the suction filter after every 20 hours of operation.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude HPC 200 86001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude HPC 200 86001 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info