Manual Gude GS4000 94621 (page 11 of 64) (English, German, Dutch, French, Italian, Polish)

628258

Zoom out

Zoom in

1/64

rubber, H07RNF type, according to DIN 57282 or DIN

57245 standards.

Never touch, lift or carry with a cable a pump

connected to network (pic. E)

It is necessary to make sure the connecting socket was not

near water and humidity and the plug was protected against

humidity.

Before putting the pump into operation, check whether the

electric cable and/or socket are not damaged.

Before any work on the pump, pull the plug out of the

socket.

Instructions step by step

• Connect the water hose to appropriate pump outlet (see

the Assembly and first putting into operation).

• Fix the rope, chain, etc. to the pump handle and place it

to the right place.

• Put the pump “sideways“ (pic. D) to the pumped

medium. Make sure the floating switch is in the operating

position.

• Plug in the pump.

• Rinse the pump with clean water after work finishing.

Floating switch positions (pic. B + C)

The operating or shutdown point of the pump can be set

with various floating switch positions. In pic. B you can see

the float cable without any fixation change with full switch

radius. The figure 1 is the working position and figure 0 the

shutdown position.

Due to appropriate fixation of the float cable, possible on the

pump handle, the switch radius can be reduced when there

is no sufficient space or at a corresponding level control.

The figure 1 in pic. C is the working position and figure 0

the shutdown position.

Failures – causes - removal

(problem): Engine does not start

(cause):

1. No system voltage

2. Blocked pump wheel

3. Floating switch in shutdown position

(measures):

1. Check the voltage

2. Inspect the pump wheel for foreign

objects

3. Check the water level (pic. B/C)

(problem): Pump does not suck

(cause):

1. Pump without water

2. Water level too low

3. Blocked pump wheel

(measures):

1. Let the air bubbles release (pic. D)

2. Switch the pump off, water level

must go up.

3. Remove the obstruction

(problem): Insufficient amount of water pumped

(cause):

1. Dirty tube filter

2. Water level quickly going down

3. Maximum head of delivery exceeded

4. Transport guide broken

(measures):

1. Clean the tube filter

2. Ensure sufficient inflow

3. Check the transport path length

4. Check the transport guide

(problem): Thermal detector switching the pump

off

(cause):

1. Dirty tube filter

2. Water temperature too high

3. Pump running continuously at

maximum pressure.

(measures):

1. Clean the tube filter and let the

pump cool down

2. Reduce the water temperature

3. Make more breaks

Inspections and maintenance

Except for the below-described cases, the pump must be

delivered to the customer service department for any repairs.

Sand and other abrasive solids cause premature wear and

pump power reduction. Works on the pump electric

equipment can explicitly be executed by the customer service

department only (that also applies for the electric cable and

float). The drowned sludge pumps are virtually maintenance-

free. Oilless bearings. Occasional filter support cleaning is

enough, no other maintenance is necessary. Original spare

parts must only be used in any case.

To ensure long service life of the pump seal, we

recommend rinsing the pump with clean water in regular

intervals.

Safety instructions for inspections and maintenance

It is always necessary to interrupt feeding (plug pulled out of

socket) and make sure the pump is not going to start before

any pump maintenance. Only a regularly maintained and

treated appliance can serve as a satisfactory aid. Insufficient

maintenance and care can lead to unforeseen accidents and

injuries.

Inspection and maintenance plan

Time interval Description Any other

details

As needed

Cleaning and rinsing

out

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude GS4000 94621 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude GS4000 94621 Manual

Product: