Manual Gude GGHA 4 in 1 95138 (page 12 of 72) (English, German, Dutch, French, Italian)

626576

Zoom out

Zoom in

1/72

Fitting the collection box

• Connect the canvas box to the metal frame (pic. 6)

and fasten it firmly to the metal frame (pic. 7) using

the plastic box clips.

• Open the rear cover and use the two hooks to

hang the collection box to the holding rod on the

cover (pic. 8)

Lawn dethatcher height calibration

• Adjust the lawn dethatcher height using the height

adjustment equipment (pic. 9).

• Turn the height adjustment equipment to the

required position and set an operating height that

is suitable.

Changing the blade shaft

• By simultaneous pressing down on both closures

you will open the front cover (pic. 1/8). (pic.10)

• To remove and insert the blade shaft,

pull the release. (pic. 11)

• Put the required extension to the shaft guide to the

right side.

Sweeping unit

• When fitting the sweeping unit, make sure the

metal part fits in its place (pic. 13 and 14)

Cutting unit

• When fitting the cutting unit, make sure both metal

parts fit in their place (pic. 15)

Dethatching unit

• When fitting the dethatching unit, make sure the

metal part fits in its place (pic. 17)

Aerating unit

• When fitting the aerating unit, make sure the metal

part fits in its place (pic. 18)

Starting the universal machine

• Before using the machine, make sure the blade or

its connecting elements are not damaged. Replace

any damaged blade if necessary.

• Before inspecting the machine, switch the engine

off and unplug the machine. To prevent

unintentional starting of the universal machine, the

2-point safety switch has been fitted with a safety

button that must be pressed before the starting

lever is pulled (pic. 19).

• When releasing the starting lever, the button must

be put to the original position.

• Make sure the extension cable is not within steel

spring reach. Press the safety switch and pull the

starting lever (pic. 19).

• Before starting your work, you must repeat this

step several times to make sure everything works

properly.

WARNING!!! You must necessarily wait until

the steel springs stop rotating and are idle in case

of any adjustment, servicing or repairs of your

universal machine. The universal machine must

necessarily be unplugged before these works.

Servicing and treatment

Pull the plug out of socket before every maintenance

and treatment! Maintain the appliance at regular intervals

(depending on the use frequency). Maintenance needs to be

strictly recorded.

• Make sure all fastening elements (screws, nuts,

etc.) are always tightened to ensure safe work with

the verticutter.

• Check the collection container more frequently for

signs of wear.

• Check the appliance regularly and replace any

worn-out or damaged parts.

Use a damp cloth to clean the plastic parts. Do not use

cleaning agents, solvents and pointed items.

Remove any dust and dirt from the machine after using it.

Empty the dirt container.

Beside this, no servicing is needed to be performed on the

machine.

Cleaning

Keep the guards, ventilation slots and engine case with no

dust and dirt if possible. Wipe the appliance with a clean

cloth or blow it with compressed air under low pressure.

Cleaning the appliance immediately after each use is

recommended. Clean the appliance regularly with a wet cloth

and a bit of liquid soap. Do not use cleaning agents and

solvents as they could damage plastic parts of the appliance.

Make sure no water gets inside the appliance.

Adjusting the cutting mechanism (pic. 17)

The cutting mechanism of your universal machine has been

adjusted to optimum before leaving the factory. If the mower

is not cutting smoothly after it has been used for a long time,

please fix the bottom blade adjustment.

Test cutting

Put a slip of paper on the bottom knife so as it points to the

knife roller axis. Turn carefully the knife roller. If the bottom

knife is adjusted properly, the paper will be cut off as if

scissors are used. Repeat the test cutting for various knives.

Right cutting

To have a well-kept lawn, we recommend cutting grass at

regular weekly intervals if possible. Grass thickens by

frequent cutting. If the grass has not been cut for a long time,

cutting should first take place in one direction with the

highest cutting height and then across with the required

cutting height. The maximum length of blades is 12 cm to be

able to be cut by the reel mower. Cut only dry grass if

possible as wet grass does not provide fine cutting.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude GGHA 4 in 1 95138 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 6,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude GGHA 4 in 1 95138 Manual

Product: