628771

Gude GESF 400 94569 Manual

15
Zoom out
Zoom in
Previous page
1/116
Next page
Being careful prevents slipping or falling, especially when
reversing.
Safety operation instructions
Do not put your hands and legs near the rotating parts.
Keep a safe distance from the eject hole.
Be extremely careful when running over or removing snow
off brash entrances, footpaths and paths. Be prepared for
unexpected risks or moving vehicles.
When you hit a foreign item, switch the engine off,
disconnect the cable from the spark plug and check
thoroughly the snow blower for any damage and remove it
if necessary – the snow blower can be put into operation
again and worked with now.
If the appliance starts abnormally vibrating, switch the
engine off and search for the cause immediately.
Generally, vibrations are a warning against operating
failure.
Switch the engine off every time you stop operating the
appliance, clean the working screw/rotor can/eject tube
and when executing repairs, adjusting and inspecting the
appliance.
When cleaning, repairing and checking the appliance,
make sure that the working screw/rotor and all moving
parts are stopped. Disconnect the spark plug cable and
secure it in a way to ensure it cannot touch the connector
and cause unwanted engine starting.
Pull the cable out of electric motors.
Do not remove snow across slopes. Be extremely careful
when changing movement direction on slopes. Never try to
remove snow on steep slopes.
Never use the snow blower when guards, sheets and other
protection components are not installed properly.
Never use the snow blower near glass surfaces, cars,
windows, pits, etc.; set the eject tube angle properly.
Children and pets must be in a sufficient distance from the
appliance.
Do not overload the appliance; do not try to remove snow
too quickly.
Never use the appliance at a high travelling speed on a
slippery surface. Be careful when reversing.
Never aim the eject tube at bystanders. Do not allow
anyone to stand before the appliance.
Disconnect the working screw/rotor drive when the snow
blower is to be transported or when not being used.
Use only extensions and accessories approved by the
snow blower manufacturer (e.g. wheel weights,
counterweight, cabins, etc.).
The snow blower must only be used when appropriate
visibility or good lighting is provided. Stand fast on the
ground and hold the handle tight by hands at all times.
Walk, never run.
Do not allow anybody to stand on the appliance.
Use the snow blower only when appropriate visibility or
good lighting is provided.
Take all safety measures when leaving the appliance
unattended.
Stop the output shaft drive, lower the extensions, shift into
neutral, apply the parking brake, switch off the engine and
pull out the key.
Caution!
At less powerful networks there might be short voltage
fluctuations when the appliance is switched on. This may
influence the function of other appliances, e.g. there might
be light intensity fluctuations. Where there is network
impendance of Zmax < 0.997 Ω, these negative influences
need not be expected (more information can be obtained
from your local energy supplier if necessary).
Use as designated
The product you have bought (electric snow blower) has
exclusively been designed for the following range of use:
Proper removal of snow from private footpaths, entrances
and parking places unless they fall within the general road
traffic regulation (e.g. public footpaths or entrances; for
that, permit specific for the given country needs to be
requested from appropriate authorities if necessary).
Only fresh snow is used as the processed material.
Any other use is in conflict with the designation. The
manufacturer is not liable for any indirect damages and
injuries. Please be sure to know that our appliances have
not been designed for industrial use.
Installation
Caution! The appliance needs to be switched off and
unplugged before maintenance, cleaning and installation.
The same must be done if the feeder cable is damaged,
incised or entangled.
Respect the system voltage: current source voltage must
correspond to the details on the appliance type label.
An extension cable with a too small wire cross section
significantly reduces the appliance performance. For
cables within a length of 25 m at least 3 x 1.5mm²; for
cables of more than 25 m of length at least 2.5mm².
Caution! Extension cables not approved must not be used.
The extension cable, plug and clutch must be watertight
and approved for outdoor use.
Cable communications must be dry and must not lie on the
ground.
If a cable drum is used, it needs to be unwound.
Some parts of the snow blower are not installed when
being transported to the buyer.
Screws, manual wheels, cable clips and screwdriver can
be found in a separate plastic bag. Installation is simple if
instructions below are followed.
Eject tube
Take the appliance and all components out of the box.
Remove all the 4 screws on the front cover and the front
part (pic. 2). Now insert the eject tube to the front hole of
the cover. Then, using the 4 screws, mount the front part
to the cover and tighten the screws in a way to make sure
the eject tube is in a safe position that can be freely turned
by 180°. Finally, using the 2 supplied wing screws, mount
the upper return flap to the eject tube.
Lower upper of the sliding post
Pull the other end of the adjusting rodding (coming from
the eject tube) on the lower part of the sliding post and
then push the lower part of the sliding post down to both
cover holes (pic. 3). Make sure that both supporting
clamps clicked into the bottom end of the lower part of the
sliding post on the cover.
Upper part of the sliding post
Bring the cable pull strain relief equipment for the
extension cable to the upper part of the sliding post (pic.
4). Make sure the cable pull strain relief equipment does
not later get in contact with the 2-point safety switch to
prevent undesirable blocking (pic. 11). Now connect both
post halves and screw them to each other using the
supplied screws with manual wheels. The adjusting
rodding is used to change the eject tube direction.
Mount the 2-point safety switch to the upper part of the
sliding post, using two screws, to the appropriate hole
unless the switch is already assembled to the upper part of
the sliding post (pic. 6).
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GESF 400 94569 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GESF 400 94569 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 6,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info